Question about Cars & Trucks

1 Answer

Not grouded correctly

Dtc po123- po222 tp app siginal high

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Cars & Trucks Master
  • 2,620 Answers

Faulty throttle position sensor.Replace sensor then reset the computer.

Posted on Oct 25, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error codes 2101 and 1516 on my 2004 chevy trailblazer


DTC P2101-
The commanded throttle position (TP), based on accelerator pedal position (APP) and possibly other limiting factors, is compared to the actual TP. The 2 values should be within a calibrated range of each other. Both the powertrain control module (PCM) and the throttle actuator control (TAC) module redundantly monitor the commanded and actual TP. This DTC sets if the PCM detects an out-of-range condition between commanded and actual throttle position.
DTC P1516
The predicted throttle position (TP) is compared to the actual throttle position. The two values should be within a calibrated range of each other. Both the powertrain control module (PCM) and the throttle actuator control (TAC) module redundantly monitor the predicted and actual throttle position. This DTC sets if the PCM detects an out of range condition between the predicted and actual throttle position.

Do you know what electronic throttle control is ?

Pt 1 2007 Chevy 2500HD Reduced Engine Power Warning Fault Code P1516...

Jul 31, 2017 | Cars & Trucks

1 Answer

Dodge caravan 2003 code p1598 and p0123


code p 1598 is a/c pressure sensor--volts to high
code p0123 refers to throttle position(TP) sensor A/ accelerator pedal position (APP) sensor A---high input===causes wiring short to positive--TP/APP sensor---ECM
it also refers to TP sensor A APP switch A--low input====causes --wiring short to ground--Tp/APP switch---ECM

Jan 19, 2017 | Dodge Caravan Cars & Trucks

1 Answer

Dtc p0121 throttle position (tp) sensor performance


code p 0121 has to answers
1--refers to throttle position (TP) sensor/accelerator pedal position sensor A--range /performance problem====causes --accelerator cable adjustment--TP/APP sensor ---wiring
The second reference is the same and the causes are--accelerator cable adjustment--TP/APP switch
(APP is accelerator pedal position)

Aug 30, 2016 | Cars & Trucks

1 Answer

What does code PO123 means?


code p0123 refers to Throttle position sensor. accelerator pedal position sensor output high cause ---wiring short---TP/APPsensor and ECM
code p0121 refers to the TP sensor APP switchA range /rformance problem
code p0135refers to heated oxygen sensor (HO2S) 1 bank 1 heater control - circuit malfunction causes may be fuse---wiring---HO
S sensor and ECM Out of all these the commom fault is the position sensor and the oxygen sensor.

Mar 10, 2013 | Cars & Trucks

1 Answer

DTC PO123 - PO222 TP APP Signal High


We do not have wiring diagrams here, they are copyrighted and not readily shared for this reason. You can access them at a few sites, one is alldatadiy.com

Oct 25, 2012 | Cars & Trucks

1 Answer

Have 2006 gmc canyon having trouble with it staying on.3.5 engine starts up,stays on a few seconds then shuts off shows reduced power on panel.won't crank over .have to wait a few minutes then it


REDUCED POWER
Refer to:
• Powertrain Control Module Description for the 2.8L engine
• Powertrain Control Module Description for the 3.5L engine

Throttle Actuator Control (TAC) System
Throttle Actuator Control (TAC) Overview
The throttle actuator control (TAC) system uses vehicle electronics and components to calculate and control the position of the throttle blade. This eliminates the need for a mechanical cable attachment from the accelerator pedal to the throttle body. This system also performs the cruise control functions as well.
The TAC system components include, but are not limited to the following:
• The accelerator pedal position (APP) sensors
• The throttle body
• The powertrain control module (PCM)
Each of these components interface together to ensure accurate calculations and control of the throttle position.

Accelerator Pedal Position (APP) Sensor
The accelerator pedal position (APP) sensor is mounted on the accelerator pedal assembly. The APP is 2 individual APP sensors within one housing. There are 2 separate signal, low reference, and 5-volt reference circuits. APP sensor 1 voltage increases as the accelerator pedal is depressed. APP sensor 2 voltage decreases as the accelerator pedal is depressed.
Throttle Body Assembly
The throttle body for the throttle actuator control (TAC) system is similar to a conventional throttle body with several exceptions. One exception being the use of a motor to control the throttle position instead of a mechanical cable. Another exception is the throttle position (TP) sensor. The TP sensor is mounted in the throttle body assembly. The TP sensor is 2 individual TP sensors within the throttle body assembly. Two separate signals, low reference, and 5-volt reference circuits are used to connect the TP sensors and the powertrain control module (PCM). TP sensor 2 signal voltage increases as the throttle opens. TP sensor 1 signal voltage decreases as the throttle opens.

Reduced Engine Power Mode
When the PCM detects a problem with the throttle actuator control (TAC) system the PCM enters one of the following Reduced Engine Power Modes:
• Acceleration Limiting--The control module will continue to use the accelerator pedal for throttle control, however the vehicle acceleration is limited.
• Limited Throttle Mode--The control module will continue to use the accelerator pedal for throttle control, however the maximum throttle opening is limited.
• Throttle Default Mode--The control module will turn OFF the throttle actuator.
• Forced Idle Mode--The control module will perform the following actions:
- Limit engine speed to idle by positioning throttle position, or by controlling fuel and spark if throttle is turned OFF.
- Ignore accelerator pedal input.
• Engine Shutdown Mode--The control module will disable fuel and de-energize the throttle actuator.

Have you had it checked for DTC'S - diagnostic trouble codes ?

DTC P2176
The commanded throttle position (TP) is compared to the actual TP. Both values should be within a calibrated range of each other. The powertrain control module (PCM) continuously monitors the commanded and actual TPs. If the values are greater than the calibrated range, DTC P2176 sets.
--------------------------------------------------------------------------------
DTC P2138
The accelerator pedal position (APP) sensors 1 and 2 are located within the accelerator pedal assembly. Each sensor has the following circuits:
• A 5-volt reference circuit
• A low reference circuit
• A signal circuit
This provides the powertrain control module (PCM) with a signal voltage proportional to accelerator pedal movement. The APP sensor 1 signal voltage at rest position is near the low reference and increases as the pedal is actuated. The APP sensor 2 signal voltage at rest position is near the 5-volt reference and decreases as the pedal is actuated.
DTC P2135
The throttle actuator control (TAC) assembly has 2 throttle position (TP) sensors mounted within the assembly. The powertrain control module (PCM) provides individual signal, ground, and 5-volt reference circuits to each sensor. Both sensors operate within a voltage range between 0.35-4.65 volts. When the throttle is opened from 0-100 percent, one sensor signal voltage increases while the other decreases. The signal circuit for TP sensor 1 is referenced to ground, and the signal circuit for TP sensor 2 is pulled up to 5 volts within the PCM.
DTC P2128
DTC P2127
DTC P2125
DTC P2123

Drive by Wire Function and diagnostics by Wells

May 25, 2017 | 2006 GMC Canyon

2 Answers

2004 jeep grand cherokee laredo, po162, po123


162 is the O2 sensor and 123 is Throttle/Pedal Position Sensor/Switch "A" Circuit High

Jun 18, 2017 | 2000 Jeep Cherokee

1 Answer

How do you fix a PO113 & PO123 code on a 02 Jeep Grand Charokee Larado 4.0



Trouble Code: P0113

IAT Sensor Circuit High Input
Possible Causes:


IAT Sensor signal circuit shorted to VREF (5v) IAT Sensor signal circuit is open, or the ground circuit is open


Trouble Code: P0123

TP Sensor/APPS Circuit High Input
Possible Causes:


Related TP Sensor engine DTCs present Intermittent wiring or connector problem TP signal circuit is open or is shorted to battery voltage or to 5v supply circuit TP sensor has failed TP sensor ground circuit is open PCM has failed IAT Sensor is damaged or it has failed (an internal open circuit) PCM has failed

Jun 02, 2012 | 2002 Jeep Grand Cherokee

1 Answer

P0123 error code, make high voltage and you change the sensor voltage is Czech but still the problem is to change the engine computer or that is the problem, we had this problem and how it turns, A / C the...


PO123 IS TP SENSOR APPS CIRCUIT HIGH INPUT. YOUR THROTTLE POSITION SENSOR IS FAULTY.CHECK THROTTLE POSITION SENSOR ELECTRICAL CONNECTOR MAKE SURE ITS NOT DAMAGED OR LOOSE.

Jun 12, 2010 | 2005 Chrysler Pacifica

3 Answers

GM service engine code P1870/2000 GMC Sonoma 2.2 cylinder


you jave a biggie here.
here is some info
CIRCUIT DESCRIPTION
The Powertrain Control Module (PCM) monitors the difference between engine speed and transmission output speed. In D3 drive range with the TCC engaged, the engine speed should closely match the transmission output speed. In D4 drive range, with the TCC engaged, the TCC slip speed should be -20 to +60 RPM .

When the PCM detects excessive TCC slip when the TCC should be engaged, then DTC P1870 sets. DTC P1870 is a type B DTC.

CONDITIONS FOR RUNNING THE DTC
  • No TP sensor DTCs P0122 or P0123.
  • No VSS assembly DTCs P0502 or P0503.
  • No TCC solenoid valve DTC P0740.
  • No 1-2 SS valve DTC P0753.
  • No 2-3 SS valve DTC P0758.
  • No 3-2 SS valve assembly DTC P0785.
  • No TCC PWM solenoid valve DTC P1860.
  • The engine is not in fuel cutoff.
  • The engine torque is 40-400 lb ft .
  • The TP angle is 12-50% .
  • The vehicle speed is 56-112 km/h (35-70 mph ).
  • The speed ratio is 0.64-0.95 (the speed ratio is the engine speed divided by the transmission output speed).
  • The engine speed is 1500-3500 RPM .
  • The gear range is D4.
  • The commanded gear is not 1st gear
  • The TFT is between 20-130°C (68-266°F) .
  • The shift solenoid performance diagnostic counters are zero.

May 16, 2008 | 2000 GMC Sonoma Extended Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...