Question about 1988 Dodge Aries

1 Answer

88 aries k wagon 2 5L i only have brakes that work on the drivers front and the pass rear.what mite be causing this ? plz help

Ive tried bleeding them many times with no success.i only seem to get fluid out of those two if i stomp the pedal real hard.but that's it.if u pump and bleed as normal there's only a trickle of fluid.the other two do as they should.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dodge Master
  • 79,865 Answers

Kinked brake line or other obstruction or a frozen wheel cylinder.

Posted on Oct 25, 2012

  • Brandan Irwin
    Brandan Irwin Dec 12, 2012

    the line appear fine and the wheel cylinders are new along with everything else.master cylinder,booster.possible i have air trapped in the system somewhere? porportioning valve maybe?

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 422 Answers

SOURCE: 98 caravan no abs

sounds to me if you replaced all of that than the power booster is sticking

Posted on Oct 27, 2008

  • 158 Answers

SOURCE: Can't find port to bleed front brakes 1995 Dodge Caravan

should be a bleeder screw on each caliper, unless, they were broken off in a previous attempt? They have to be there

Posted on Apr 07, 2009

  • 139 Answers

SOURCE: bleeding brakes

always bleed front driver side first, front right,left back
right back.
make sure you always have oil in the master

Posted on Apr 09, 2009

  • 151 Answers

SOURCE: 2001.5 Dodge Ram Diesel 2500 4x4 Brake Pedal drops to floor

It sounds like you have a bad mastercylinder cause when you panic brake it doesn't have time to bleed through the valve in the cylinder but under normal braking your foot is on pedal longer in turn giving the fluid time to bypass the valve in the mastercylinder in turn the pedal going to the floor.

Posted on Apr 21, 2010

Testimonial: "thnx"

SOURCE: i cant get the air to bleed out of my brakes on a

You need a helper, to slowly press the brake pedal down, as you open bleeder valve,then close before your helper gets near the floor.
Repeat until all air is out of each wheel position.
RR,LR,RF then LF. Always start from the farthest wheel and have motor running
Never pump brakes. That does nothing at all.

Posted on Nov 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

What is the brake bleed order on a 2007 toyota sienna?


Although many people believe that the order makes a difference in their particular vehicle, there are many others who service many different makes and models of vehicles and generally conclude that the order makes no difference.

"I have investigated this brake bleeding sequence controversy and went interviewing professional mechanics from Porsche, Mercedes Benz, Toyota, Volkswagen etc. including from Pep Boys just to get to the bottom of the story. If you use the pressure or vacuum bleeding or the manual pedal method correctly, the sequence does not matter.

So I built a test rig using clear and transparent brake lines with 4 different color brake fluids. Whether you start from the farthest or the nearest brake caliper, the brake system could be bled correctly without compromising safety. This is a myth (RR, LR, FR, FL sequence) that has been accepted by most people.

What I found out was that people who use the farthest method sequence have not tried other sequences because they believe it is the only way to do it. While others who used random bleeding succesfully know sequence is not mandatory."

I'm a "random bleeder" myself, and have never had a problem. I simply proceed either clockwise or anti-clockwise around the car, for simplicity.

Nov 13, 2017 | Toyota Cars & Trucks

1 Answer

Brake bleeding


keep bleeding and you need two people to bleed brakes using pedal pump method --fill master with fluid and have some one pump and hold then open bleeder then close it --then have the some one pumps again [ repeat steps ] when no air -go to next wheel and check in beetween fluid level adding when needed
How To Bleed Brakes Yahoo Video Search Results How to Bleed Your Brakes dummies How to Bleed Car Brakes

Jul 28, 2017 | 1999 Mazda 626

2 Answers

Brakes not working right


you need to bleed your master cylinder also. you are going to need help pumping on the brakes. and you can bleed your brakes on the master cylinder lines just you bleed your brakes.

Jan 22, 2018 | 1997 Nissan 200SX

1 Answer

2006 HYUNDAI Sonata I figured I'd bleed the the rear brakes after replacing the rotors and pads. 120,000 Miles with no previous brake issues besides normal replacement of front rotors and pads. After...


Try re-bleeding ALL wheels starting with furthest away - pass rear, then driv rear, then pass front and driv front. That should get your pedal back. To reset light you need ABS reset tool and it's EXPENSIVE. Have a good competent shop reset it for you. Body shops can reset them also.

Feb 27, 2011 | 2006 Hyundai Sonata

1 Answer

Just Put New Brake Line On,Now Can`t Pump up Brakes After Bleeding.


WHEN BLEEDING THE BRAKES, YOU MUST HAVE A FULL RESEVOIR WITH CAP ON. START WITH PASS. REAR, PUMP BRAKE PEDLE ALL THE WAY DOWN ABOUT 3 TIMES AND HOLD DOWN. OPEN BLEEDER SCREW TILL NOTHING COMES OUT, THEN CLOSE. REPEAT UNTIL THERE IS NO AIR COMING OUT. IT IS IMPORTANT TO BUILD UP PRESSURE WITH ATLEAST 3 PUMPS IN ORDER FOR THIS TO WORK. REPEAT ON DRIVER REAR, THE PASS. FRONT, THEN DRIVER FRONT. HOPE THIS HELPS.

Oct 10, 2010 | 1990 Oldsmobile Regency

5 Answers

Is there a bleeding sequence for a 1990 Toyota Four Runner? We replaced one front driver side brake line and both calipers and we cannot seem to get it to bleed properly. Thanks


normally, the brakes are bled starting from the furthest brake to the closest with respect to the master brake cylinder. the sequence is : right rear, left rear, right front, left front. pump the brakes until pressure is built up. do this rather slowly. while keeping downward pressure on the pedal, open the bleed screw slowly. the pedal will go to the floor. hold the pedal on the floor and tighten the bleed screw. do this until no air is observed. keep the reservoir. repeat with the rest of the brakes following in sequence

http://www.aa1car.com/library/2003/bf90347.htm

May 31, 2010 | 1990 Toyota 4Runner

1 Answer

Replaced the front pads on my 99 suburban, but


pedal gets hard when turned of because they are power brakes plus theres no vaccum try bleeding the brakes if theres still a problem check the master cylinder and fluid level when brakes wear down they require more fluid but try first bleeding remember start at pass rear driver rear and pass front and last driver front

Aug 30, 2009 | GMC Suburban Cars & Trucks

1 Answer

Trouble Bleeding Break Line


you need to hold in the metering valve.when you bleed the front brakes.long as the valve closed off you wont be able to bleed front brakes.better to get extra help.hard to bleed by your self .

Apr 20, 2009 | 1988 Oldsmobile Delta 88

1 Answer

92 dodge van rear ABS-brake and ABS lights on/can't reset?


Its probably how your bleeding your brakes, but first make sure the bleeding nipples are facing upward. You should bleed diagonaly, front pass wheel then rear driver wheel. Then front driver wheel and rear pass wheel. The abs light has its own computer your have to get it scanned to clear the codes and turn off the light

Mar 18, 2009 | 1992 Oldsmobile Ninety Eight Regency

Not finding what you are looking for?
Cars & Trucks Logo

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...