Question about 2005 Pontiac Grand Am

Open Question

Cylinder head bolts tightening sequence on04 grand am 2.2

Cylinder head

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 16 Answers

SOURCE: 1991 Pontiac Sunbird Head bolt torque sequence and timing marks

torque sequence for head bolts start in the middle of the head barely tighten this and work your way out doing one bolt toward the back and one toward the front on the second pass torque to 30 ft lbs on the second pass torque to 60 ft lbs dunno about the timing marks

Posted on May 01, 2009

  • 47 Answers

SOURCE: we need to know how to tighten the head and intake

i would recomend double check but am almost positive because is been the same torque for many years for this engine and is 33 ft.lbs plus 90 degrees and the sequence

6 2 3 7
5 1 4 8
front of the engine lefth head(front of the car)

5 1 4 8
6 2 3 7 rigth one (firewall)

Posted on Sep 24, 2009

SOURCE: torck sequence for pontiac sunfire 1999 2.2 l and

go to your local library and check their reference section for MOTOR Manuals. They cover domestic cars back to the 60's and they have nice detailed torque tables for your car. You can make a photocopy *(my library has a free copier) of the needed pages and be on your way!

Posted on Dec 21, 2009

  • 3640 Answers

SOURCE: I have a pontiac and i keep blowing head gasket on

cylinder head bolts, step one;33 ft. lbs, second step rotate an additional 90-degrees (1/4 turn). do not put any oil or sealant on gasket. the gasket should seal itself if torqued properly.

Posted on Apr 16, 2010

iambanshee74
  • 3489 Answers

SOURCE: want to know the amount of torque pressure do i

To install:

0996b43f80208f65.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head bolt torque sequence-3.8L engine

  1. Install the new cylinder head gasket with the arrow pointing to the front of the engine.
  2. Install the cylinder head.
  3. Install NEW cylinder head bolts. Torque the bolts in sequence, as follows:
    1. Step 1: 37 ft. lbs. (50 Nm).
    2. Step 2: Plus 120 degree turn.
To install:

0996b43f802316ea.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Tighten the cylinder head bolts using the following sequence-31L and 3.4L engines

  1. Install the cylinder head with a new gasket.
  2. Apply thread sealer to the head bolts.
  3. Tighten the cylinder head bolts to 37 ft. lbs. (50 Nm) plus an additional 90 degree turn.

Posted on Dec 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the cylinder head tighten torque


Have a look on this link. You may be able to find your car:

SPECIFICATION LOOKUPS

Cylinder head bolts are usually tightened to around 65 ft-lbs, depending on what the car is.

There's more than 4 cylinder head bolts... There's usually 10 bolts.
There's also a sequence for tightening the bolts:

cylinder head tightening order Google Search

When tightening cylinder head bolts do it in 'stages' and follow the sequence .. ie.. tighten the bolts finger tight first, then torque them up to about 25 ft-lbs. Wait 2 minutes.

Then tighten them to about 45 ft-lbs in sequence. Wait 2 minutes.

Do it again up to about 55 ft-lbs. Wait 2 minutes.

Tighten them up to 65 ft-lbs or whatever is recommended for your car.

Tightening in order/sequence pulls the cylinder head evenly onto the block. Waiting 2 minutes between stages allows a 'stretched' bolt to 'settle'.

Feb 17, 2016 | Cars & Trucks

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

2 Answers

Dear expert What are the cylinder head bolt torque settings for the 4.0L MFI straight 6 engine? Regards Dave


Here are the specs and sequence:

0900c152800a9943.gif

Install the cylinder head and bolts. The threads of bolt No. 11 must be coated with Loctite® 592 sealant before installation. Tighten the bolts in 3 steps, using the correct sequence:

  1. Tighten all bolts to 22 ft. lbs. (30 Nm).
  2. Tighten all bolts to 45 ft. lbs. (61 Nm).
  3. Retighten all bolts to 45 ft. lbs. (61 Nm).
  4. Tighten bolts 1 through 10 in sequence to 110 ft. lbs. (150 Nm).
  5. Tighten bolt 11 to 100 ft. lbs. (136 Nm)
  6. Tighten bolts 12 through 14 to 110 ft. lbs. (150 Nm)

May 04, 2011 | 1996 Jeep Grand Cherokee

1 Answer

Want to know the amount of torque pressure do i use when tightening the head bolts, and whats the sequence?


To install:

0996b43f80208f65.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Cylinder head bolt torque sequence-3.8L engine

  1. Install the new cylinder head gasket with the arrow pointing to the front of the engine.
  2. Install the cylinder head.
  3. Install NEW cylinder head bolts. Torque the bolts in sequence, as follows:
    1. Step 1: 37 ft. lbs. (50 Nm).
    2. Step 2: Plus 120 degree turn.
To install:

0996b43f802316ea.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Tighten the cylinder head bolts using the following sequence-31L and 3.4L engines

  1. Install the cylinder head with a new gasket.
  2. Apply thread sealer to the head bolts.
  3. Tighten the cylinder head bolts to 37 ft. lbs. (50 Nm) plus an additional 90 degree turn.

Dec 16, 2010 | 2002 Pontiac Grand Prix

3 Answers

How do I remove the head? (Blown Head gasket)


prev.gif next.gif Cylinder Head REMOVAL & INSTALLATION 2.3L Engine
  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable, then drain cooling system into a suitable container.
  3. Detach the heater inlet and throttle body heater hoses from water outlet. If accessible at this time, disconnect the upper radiator hose from the water outlet.
  4. Remove the exhaust manifold. For details, please refer to the procedure located in this section.
  5. Remove the intake (camshaft housing for SOHC) and exhaust (DOHC only) camshaft housings.
  6. Unfasten the oil fill tube bolt/screw then remove the oil fill cap and level indicator assembly. Pull the oil fill tube upward to unseat from block.
  7. Label and disengage the injector harness electrical connector.
  8. Detach the throttle body-to-air intake duct.
  9. Tag and disconnect the power brake vacuum hose from the throttle body.
  10. Remove the throttle cable bracket.
  11. Remove the throttle body from the intake manifold with the electrical harness and throttle cable attached and position the assembly aside.
  12. Tag and disconnect the MAP sensor vacuum hose from the intake manifold, then remove the intake manifold brace.
  13. Detach the electrical connectors from the MAP sensor, IAT sensor and the EVAP canister purge solenoid.
  14. If not already done, detach the upper (inlet) radiator hose from the water outlet.
  15. Disengage the coolant temperature sensor connector(s).
  16. Unfasten the cylinder head bolts in reverse order of the installation sequence shown in the accompanying figures.
  17. Lift the cylinder head from the engine block. Remove and discard the gasket. Inspect the oil flow check valve for freedom of movement.
  18. Using a suitable solvent, thoroughly clean and dry all bolts, bolt holes and mating surfaces. Inspect the head bolts for any damage and replace, if necessary. If using a scraper to clean the old gasket material from the mating surfaces, use only a plastic or wood one, NOT a metal scraper. Do NOT allow any debris to fall into the engine! To install:
  19. Place a new cylinder head gasket on the cylinder block, then carefully position the cylinder head in place.
  20. Sparingly coat the head bolt threads with clean engine oil, then allow the oil to drain off before installing.
  21. On 1988-89 engines, install and tighten the cylinder head bolts, in sequence, as follows:
    • Step 1 - Tighten all head bolts in sequence to 26 ft. lbs. (35 Nm)
    • Step 2 - Using a torque angle meter, tighten the short bolts an additional 80°and the long bolts an additional 90°in sequence Fig. 5: Cylinder head bolt tightening sequence - 1988-89 2.3L engine 86883121.gif
  22. On 1990-91 engines, tighten the cylinder head bolts, in sequence, as follows:
    • Step 1 - Tighten all head bolts in sequence to 26 ft. lbs. (35 Nm)
    • Step 2 - Using a torque angle meter, tighten the short bolts an additional 100°and the long bolts an additional 110°in sequence Fig. 6: Cylinder head bolt tightening sequence - 1990-91 2.3L engine 86883122.gif
  23. On 1992 engines, tighten the cylinder head bolts, in sequence, as follows:
    • Step 1 - Tighten, in sequence, head bolts 1-6 to 26 ft. lbs. (35 Nm), 7-8 to 15 ft. lbs. (20 Nm) and 9-10 to 22 ft. lbs. (30 Nm).
    • Step 2 - Tighten all head bolts, in sequence, an additional 90°using J 36660 or equivalent
    • Step 3 - In sequence, loosen each bolt one turn, then immediately re-tighten to the specified torque
    • Step 4 - After completing step 3 on all 10 bolts, tighten each bolt, in sequence, an additional 90° Fig. 7: Cylinder head bolt tightening sequence - 1992 2.3L engine 86883123.gif
  24. On 1993-95 vehicles, tighten the cylinder head bolts to the specifications shown in the accompanying figures. Fig. 8: Cylinder head bolt tightening sequence and specifications - 1993 2.3L engine 86883124.gif
    Fig. 9: Cylinder head bolt tightening sequence and specifications - 1994-95 2.3L engine 86883125.gif
  25. Engage the coolant temperature sensor electrical connector(s).
  26. Connect the upper radiator hose to the water outlet.
  27. Install the intake manifold bracket.
  28. Attach the following electrical connections: MAP sensor, IAT sensor, and the purge solenoid.
  29. Using a new gasket, install the throttle body to the intake manifold.
  30. Install the accelerator control cable bracket.
  31. Connect the throttle body-to-air intake duct.
  32. Install the oil fill tube and level indicator.
  33. Install the camshaft housing(s).
  34. Install the exhaust manifold. For details, please refer to the procedure located in this section.
  35. Connect the heater inlet and throttle body heater hoses to the water outlet.
  36. Fill all fluids to their proper levels.
  37. Connect the battery cable, start the engine and check for leaks.

Sep 24, 2010 | 1992 Oldsmobile Achieva

1 Answer

Whats the bolt pattern for my 1995 ford escort head?


1.8 liter..NOTE: Lubricate the cylinder head bolts using the specified engine oil.

Install the cylinder head bolts. Tighten the cylinder head bolts in 2 or 3 steps in the sequence shown to 76-81 Nm (56-60 lb-ft).

b064be7.gif
1.9 liter
Apply a light coating of engine oil to the threads of the new cylinder head bolts. Install the new cylinder head bolts to the cylinder head. Following the sequence shown below, tighten the cylinder head bolts to 40-60 Nm (30-44 lb-ft). Loosen all cylinder head bolts approximately two turns, then retighten the cylinder head bolts to 60 Nm (44 lb-ft) following the sequence shown. After tightening, turn all bolts 90 degrees, in the same sequence. Complete bolt tightening by turning them an additional 90 degrees, in the same sequence. 398246b.gif

Aug 21, 2010 | 1995 Ford Escort

2 Answers

What r the torque specifications on installing a head on a 1999 yukon and the tightening sequence


Check this procedure...
  1. Tighten the first design cylinder head bolts as follows:
    1. M11 bolts 1st pass: in sequence to 22 ft. lbs. (30 Nm).
    2. M11 bolts 2nd pass: in sequence + 90 degrees.
    3. M11 bolts (1,2,3,4,5,6,7,8): + 90 degrees.
    4. M11 bolts (9 and 10): + 50 degrees.
    5. M8 cylinder head bolts (11,12,13,14,15) to 22 ft. lbs. (30 Nm). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.
  2. Tighten the second design cylinder head bolts as follows:
    1. M11 bolts (1-10) 1st pass: in sequence to 22 ft. lbs. (30 Nm).
    2. M11 bolts (1-10) 2nd pass: in sequence + 90 degrees.
    3. M11 bolts (1-10): + 70 degrees.
    4. M8 cylinder head bolts (11,12,13,14,15) to 22 ft. lbs. (30 Nm). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.

c409909.jpg

Fig. Cylinder head bolt tightening sequence-4.8L, 5.3L and 6.0L engines (click for zoom)


Install the cylinder head bolts in sequence to 22 ft. lbs. (30 Nm). The bolts must be tightened once, then be tightened again in sequence in the following order:
  1. Step 1: Short length bolt: (3, 4, 7, 8, 11, 12, 15, 16), plus 55 degrees.
  2. Step 2: Medium length bolt: (14, 17), plus 65 degrees.
  3. Step 3: Long length bolts: (1, 2, 5, 6, 9, 10, 13), plus 75 degrees.

7f05cb7.jpg

Fig. Cylinder head bolt tightening sequence-5.0L and 5.7L engines

Aug 04, 2010 | 1999 GMC Yukon Denali

1 Answer

What is the right Torque Specification of the cylinder head bolt,main bearing and connecting rod bearing for a 1997 Ford F 150 4.2 liter? Thank you...


Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

May 17, 2010 | 1997 Ford F150 Regular Cab

1 Answer

Torque specs for cylinder head on a 200 ford focus with 2.0 ltr single overhead cam. and for connecting rod... Thank you much.


  1. CAUTION: Always install new cylinder head bolts. NOTE: Lubricate the cylinder head bolts with Super Premium 5W 30 SAE X0-5W 30-QSP or equivalent meeting Ford specification WSS-M2C153-G prior to installation. Install the cylinder head assembly and tighten the cylinder head bolts in the following sequence.
  1. Tighten all bolts in a single sequence to 50 Nm
  2. Back the bolts off 1/2 turn.
  3. Tighten the bolts in sequence shown to 50 Nm .
  4. Rotate all the bolts in a single sequence an additional 180 degrees in two steps of 90 degrees each.
9 3 1 5 7
8 6 2 4 10 sequence for head


Spec for rod 38Nm

May 07, 2010 | 2000 Ford Focus

2 Answers

What is the tension on cylinder head bolts for a jeep grand cherokee 307935 4 litre, 6 cylinder, 1999, petrol motor.


Coat threads of left hand front bolt with sealant: 1st - step; - 22 ft./lbs. 2nd - step; - 45 ft./lbs. 3rd - step, all bolts except L.H. front bolt; - 110 ft./lbs. 4th - step, L.H. front bolt; - 100 ft./lbs. fig100.png

Sep 05, 2009 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...