Question about 2001 GMC Yukon

1 Answer

WINDSHIELD WASHER RESEVOIR IS LEAKING. HOW DO WE REMOVE AND REPLACE

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

How bad is it leaking?if its' a small leak maybe duct tape it if you dont really want to replace it.maybe that would get you by for awhile...

Posted on Jan 08, 2009

3 Suggested Answers

  • 1 Answer

SOURCE: need to remove windshield washer resevoir

If you here the pump working check the hose to windshield to see it was pinched when closins the hood .I fixed mine wih black electrical tape and it works fine for now.

Posted on Mar 19, 2009

  • 16 Answers

SOURCE: Removing the windshield washer reservoir in a 2002 Chrysler T&C

REMOVAL

  1. Disconnect and isolate the battery negative cable.
  2. Remove the engine fresh air housing inside the engine compartment.
  3. Disconnect the washer hose at the in-line connector forward of the cowl grille so that the in-line connector remains with the washer hose from the fresh air plenum.
  4. Disconnect the washer hose from the hose clip located on the front fender side shield.
  5. Remove the filler tube screw.
  6. Hoist and support vehicle on hoist or jack stands.
  7. Remove the right front wheel and tire assembly.
  8. Disconnect the left right front wheelhouse splash shield and move aside.
  9. Drain washer fluid from the reservoir and into a suitable clean container. This can be done by disconnecting the windshield washer hose from the front (outboard) washer pump and allowing the washer fluid to drain into a container through a temporary jumper hose connected to the front washer pump.
  10. Disconnect the electrical body harness connectors to the washer pump motors and the fluid level sensor. Slide the red lock on the connector to the release position, then, depress the black tab and pull the connector off the pump or sensor.
  11. Remove the two reservoir mounting screws.
  12. Disconnect the reservoir from the body mount by raising the reservoir upward slightly and then down so that the reservoir filler neck and front washer hose pull through the opening in the front fender side shield.
INSTALLATION

  1. Push filler neck and front washer hose through the opening in the front fender side shield. Connect the reservoir to the body mount by lowering the reservoir down.
  2. Install the two reservoir mounting screws. Torque screws to 8.5 - 11.3 Nm (75 - 100 in. lbs.) .
  3. Connect the electrical body harness connectors to the washer pump motors and the fluid level sensor. Slide the red lock on the connector to the closed or locked position.
  4. Assure that washer is properly routed to prevent pinching and possible inoperative washers.
  5. Connect the left right front wheelhouse splash shield and move aside.
  6. Install the right front wheel and tire assembly.
  7. lower vehicle from hoist or jack stands.
  8. Install the filler tube screw. Torque screw to 8.5 - 11.3 Nm (75 - 100 in. lbs.) .
  9. Connect the washer hose to the hose clip located on the front fender side shield.
  10. Connect the washer hose at the in-line connector forward of the cowl grille.
  11. Install the engine fresh air housing inside the engine compartment.
  12. Connect the battery negative cable.
  13. Verify system operation.

Posted on Apr 01, 2009

  • 72 Answers

SOURCE: how do you get to the windshield washer resevoir

Take off cover under wheel arch and under front bumper its probly the motor that runs the pump.

Posted on Aug 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Windshield washer liquid leaking


Could be a couple of things ,,,, If the washer resevoir frooze in the recent past it could have split the motor/bottle or hoses attached, it may also be the anti return valve (Y shaped) on the hose work split and causing a drip !

Aug 26, 2012 | 2003 Acura 3.2TL

2 Answers

Windshield washer pump not working. I want to know where it is located and how to replace it.


The washer pump is located directly on the washer solvent resevoir, to remove it just disconnect the washer solvent hose and pump electrical connector, then just pull motor outward. it is just a snap type fit to the resevoir.

Jan 19, 2011 | 1998 Jeep Cherokee

1 Answer

How to replace the windshield washer pump


pump is in washer resevoir. disconnect electrical plug and hoses then pull pump out.

May 10, 2010 | 1999 Chevrolet Lumina

1 Answer

Windshield Washer Pump Works But No Fluid Flow


May be the resevoir bottle may have something stuck in it, you are right, you may have a clogged line. Also check the routing of the hoses to the squirt that they are not pinched or kinked. Any washer fuild leaking anywhere?

Mar 13, 2010 | 1998 Mitsubishi Montero Sport

2 Answers

The windshield does't work push bottem still no water coming


I'm sure you filled the washer resevoir 1st. If so then listen for the washer motor with the key "on" with engine off. If no washer motor sound then that will have to be diagnosed. If the motor is heard then look for a leaking or disconnected line.

Oct 17, 2009 | 2003 Honda CR-V

1 Answer

Need to remove windshield washer resevoir


If you here the pump working check the hose to windshield to see it was pinched when closins the hood .I fixed mine wih black electrical tape and it works fine for now.

Mar 07, 2009 | 2001 Ford Taurus

2 Answers

Wiper fluid level sensor replacement


Reservoir —Windshield Wiper

Removal
  1. Remove the RH wheel; refer to Section 204-04 .
  1. Position RH splash shield aside.
    1. Remove six screws.
    1. Remove three pin-type retainers.
    1. Position RH splash shield aside.
  1. NOTE: Windshield washer fluid should be collected in a container after the windshield washer hoses are disconnected.
    Disconnect the electrical connector and washer hoses.
  1. Remove the upper reservoir bolt.
  1. Remove the windshield washer reservoir.
    • Loosen the two lower reservoir bolts.
------------------------------------------------------------------------------------

Jan 15, 2009 | 2000 Mercury Villager

1 Answer

Windshield washer pump is very weak.


you have to remove the whole resevoir to get access to it and then it's quite simple to replace.

Sep 05, 2008 | 1996 Dodge Caravan

2 Answers

I have a 2001 saturn sl and i purchased a repair book from parts store. My windshield washer pump is out and i need to replace. The book does not address this problem. How do i replace it?


First locate the washer fluid resevoir, if you can remove it the pump is usually connected to the bottom or side of the resevoir. just remove and replace the pump and then reinstall the resevoir.

Jul 26, 2008 | 1992 Saturn SL1

Not finding what you are looking for?
2001 GMC Yukon Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...