Question about Cars & Trucks

Open Question

Nissan ud ne6 remove & replace cylinder head - Cars & Trucks

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

c17hydro
  • 2984 Answers

SOURCE: cylinder head removal on 2005 nissan altima 2.5

CYLINDER HEAD REMOVAL

2.5L Engines

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain cooling system and engine oil.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Upper radiator hose and heater hose
    • Right side fuse/relay box and move aside
    • Engine undercover
    • Resonator and air cleaner case
    • Engine top cover
    • All electrical and vacuum lines at the head
    • Fuse hose quick connector at fuel tube side
    • Engine harness and power steering hose bracket
    • Timing chain
    • Drive belt tensioner
    • Camshafts
    • Spark plugs
    • Exhaust manifold
  5. Support the engine from above and below with a suitable jack and hoist.
  6. Remove or disconnect the following:
    • Power steering pump and reservoir and wire aside
    • Auxiliary drive belts
    • A/C compressor and wire aside
    • Upper sway bar links
    • Front and rear engine mount through bolts
    • Lower ball joints
    • 2 steering gear housing mounting bolts
    • Front suspension member bolts and front suspension member
  7. Loosen the cylinder head bolts in the sequence shown and remove the cylinder head.
d365038.gif
Removing the front suspension member—Altima

7555308.gif
Cylinder head bolt removal sequence—2.5L engine–Altima and Sentra

1e6ce81.gif
Cylinder head bolt tightening sequence—2.5L engine–Altima and Sentra

To install:
  1. Clean the gasket surfaces.
  2. Using new head gaskets, install the cylinder heads.
    NOTE If possible, replacement of the head bolts is suggested.

  3. If replacement of the head bolts is not possible, perform the following bolt measurement:
    • Measure the diameter of the head bolt 0.43 in. (11mm) from the bottom of the bolt.
    • Measure the diameter of the head bolt 2.17 in. (55mm) from the bottom of the bolt.
    • Whenever the size difference between the 2 measurements exceeds 0.0091 in. (0.23mm) the head bolts must be replaced.
  4. Apply clean engine oil to the bolt threads and seating surfaces and tighten the cylinder head bolts in sequence as follows:
    • Step 1: 72 ft. lbs. (98 Nm).
    • Step 2: Loosen all the bolts completely.
    • Step 2: 29 ft. lbs. (33 Nm).
    • Step 4: Plus 75–80 degrees clockwise.
    • Step 5: Plus 75–80 degrees clockwise.
  5. Install the front suspension member and tighten the bolts to the specifications shown in the illustration.
  6. Install or connect the following:
    • 2 steering gear housing mounting bolts
    • Lower ball joints
    • Front and rear engine mount through bolts
    • Upper sway bar links
    • A/C compressor
    • Auxiliary drive belts
    • Power steering pump and reservoir
    • Exhaust manifold
    • Spark plugs
    • Camshafts
    • Drive belt tensioner
    • Timing chain
    • Engine harness and power steering hose bracket
    • Fuse hose quick connector at fuel tube side
    • All electrical and vacuum lines at the head
    • Engine top cover
    • Resonator and air cleaner case
    • Engine undercover
    • Right side fuse/relay box and move aside
    • Upper radiator hose and heater hose
    • Negative battery cable
  7. Fill the cooling system and engine oil
  8. Start the vehicle, check for leaks and repair if necessary.

Posted on Nov 13, 2009

  • 23 Answers

SOURCE: 03 nissan 350z w0nt idle & stalls

YOU HAVE A VACUUM LEAK OR THE IDLE AIR CONTROL MOTOR ISNT FUNCTIONING OR NOT PLUGGED IN.POSSIBLE PLUG OR PIN DAMAGE IF PLUGGED IN.

Posted on Oct 10, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002nissan3.5cylinderheadtorque



2_17_2012_6_58_18_pm.jpg

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:

  1. Step 1: 72 ft. lbs. (98 Nm).
  2. Step 2: Completely loosen all bolts.
  3. Step 3: 26-32 ft. lbs. (34-44 Nm).
  4. Step 4: plus 90-95 degrees clockwise.
  5. Step 5: plus 90-95 degrees clockwise.

2_17_2012_6_59_54_pm.jpg

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine


2_17_2012_7_00_21_pm.jpg

Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Apr 12, 2012 | Cars & Trucks

2 Answers

2002 nissan maxima 3.5 cylinder head torque


Hi there:

2_17_2012_6_58_18_pm.jpg

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:
  1. Step 1: 72 ft. lbs. (98 Nm).
  2. Step 2: Completely loosen all bolts.
  3. Step 3: 26-32 ft. lbs. (34-44 Nm).
  4. Step 4: plus 90-95 degrees clockwise.
  5. Step 5: plus 90-95 degrees clockwise.

2_17_2012_6_59_54_pm.jpg

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine


2_17_2012_7_00_21_pm.jpg

Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Feb 17, 2012 | Nissan Cars & Trucks

1 Answer

Torque setting head 2002 nissan maxima


Hi there:

2_17_2012_6_58_18_pm.jpg

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:
  1. Step 1: 72 ft. lbs. (98 Nm).
  2. Step 2: Completely loosen all bolts.
  3. Step 3: 26-32 ft. lbs. (34-44 Nm).
  4. Step 4: plus 90-95 degrees clockwise.
  5. Step 5: plus 90-95 degrees clockwise.

2_17_2012_6_59_54_pm.jpg

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine


2_17_2012_7_00_21_pm.jpg

Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 17, 2012 | Nissan Maxima Cars & Trucks

1 Answer

I need take out cilinder head from nissan 1985 2.4 becuse the head gasket are burne out


Check this about Cylinder Head Cover - REMOVAL & INSTALLATION procedure...

1. Remove the air cleaner assembly.
2. Disconnect the PCV hose(s) from the cylinder head cover.
3. Remove the nuts and washers. Lift the cover off the cylinder head. Cover the oil return hole in the head to prevent dirt or objects from falling in. Remove the gasket.

To install:

4. Replace the cover gasket if it shows any signs of damage, breaks or cracking. Tighten the nuts evenly, reconnect the PCV hose and install the air cleaner assembly.



continue...

Apr 13, 2011 | Nissan Pickup Cars & Trucks

6 Answers

I have a 2002 Nissan Altima 2.5L that is leaking oil into the spark plug tubes; can these seals be replaced or does the valve cover have to be replaced?


Yes, you need a Rocker cover (valve cover) Gasket kit. Remove the valve cover, remove all old O-rings and cover gasket, clean grooves and mating surfaces without gouging or scratching them, put the new gaskets on as per factory recommendations, tighten to the proper torque and you're done. The spark plug holes in the cover are part of the valve cover gasket kit. Any Napa, Car Quest, Pep Boys, Auto Zone will have it.

Oct 03, 2010 | 2002 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...