Question about 2008 Ford Fusion 2.3

Open Question

How to install serpentine belt 2008 ford fusion 2.3 liter engine

Sepentine replacement

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

johnjohn2
  • 5763 Answers

SOURCE: serpentine belt diagram 2006 ford fusion

Heres the belt diagram for a 2006 fusion hope this helps.4fa451c.png

Posted on Sep 18, 2010

johnny5846
  • 379 Answers

SOURCE: need a diagram for serpentine belt 1998 Ford Contour 4cyl 2.0l.

98 ford contour 2.0 belt routing

here is a picture of routing and how to do it , etc. , good resource ..

J5

Posted on Jan 19, 2009

blueextc3221
  • 15935 Answers

SOURCE: need diagram of serpentine belt for 94Solution for "need diagram for replacing serpentine belt for 94 ford taurus gl w/3 0 v6 engine and a/c" ford taurus gl w/3.0 v6 engine and a/c

89beac5.gif Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on May 21, 2009

  • 1 Answer

SOURCE: 2008 Ford Fusion Wing Mirror Replacement

I checked Ford Focus mirror replacement and it seems to be the same. This is for the manual, unheated mirror.

Remove the mirror cover inside the door - slide a screwdriver behind the cover and pry loose carefully.

Remove the single 10mm bolt and the mirror comes free.
NB. Do not drop the bolt into the door.

Posted on May 22, 2009

digritz
  • 530 Answers

SOURCE: i need a serpentine belt diagram

Below is a link that should be able to help.
Just choose the make, model, engine. Then in the list that opens there will be a link to a belt diagram. I just went through it so it should work for you.
Good luck


http://www.mvreader.com/multiview/dayco/index.php?bgInterchange=1&l=n

Posted on Aug 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace belt in a 08 ford fusion


Anon, Take a picture of belt routing before you start as you may forget how to route belt when putting new one on. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
changing the serp belt 2 3L 2 5L
HOW TO REPLACE SERPENTINE BELT
How To Change Serpentine Drive Belt Ford Focus

Jun 01, 2016 | 2008 Ford Fusion

1 Answer

How to tighten the belt on 2008 ford fusion


Hi Brian:
Serpentine belt?
Tension comes from spring loaded idler pulley.
Sometimes they get stiff on the hinge mechanism.
I'd use my flex bar to slack it, then remove the belt, move the idler back and forth a few times to loosen it up. and then re-install the belt.

Jan 19, 2016 | Ford Cars & Trucks

1 Answer

How to remove and replace passenger side mirror on a 2014 ford fusion


Replace Your Car Passenger Side Mirror - How To - DIY ...

? 3:46
https://www.youtube.com/watch?v=77lBQ_CRqdo
Apr 10, 2012 - Uploaded by GregHint
See how even a novice can repair a passenger mirror on a FordEscape. ... Replace Your Car Passenger Side Mirror - How To - DIY .... Replace 2003-2008 Toyota Corolla Side Mirror, How to Change Install 2004 2005 2006
About 22,000 results (0.61 seconds) Search ResultsHow-To: Replace Ford Fusion side mirror (HD) - YouTube? 7:27https://www.youtube.com/watch?v=iGHeXUbvvJsMay 7, 2014 - Uploaded by Derrick HardingFord Fusion SEL 3.0 Liter V6 How to fix broken side mirrorIncludes: ... Published on May 7, 2014 ..... Great instructions - just replaced the driver's side mirror on my 2007 Fusion following your instructions. ... Front brake pad replacement 2006 - 2012 Ford Fusion Lincoln Mazda Pads Rotor Install Remove ...

Jan 08, 2016 | Ford Cars & Trucks

1 Answer

How to change water pump on a 2009 Ford Fusion


2.3L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009
  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Loosen the 3 coolant pump pulley bolts.
  4. Remove the accessory drive belt.
  5. Remove the 3 bolts and the coolant pump pulley.
    1. To install, tighten to 15 ft. lbs. (20 Nm).
  6. Remove the 3 bolts and the coolant pump.
  7. Remove and discard the O-ring seal.
    1. To install, tighten to 89 inch lbs. (10 Nm).


25940856-ldxojubx5kaly1k2zv3zks4n-2-0.gif Fig. Exploded view of the water pump-2.3L engine


To install:
  1. To install, reverse the removal procedure.
  2. Lubricate the O-ring seal with clean engine coolant.
  3. Fill and bleed the cooling system

3.0L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009
  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Remove the coolant pump belt.
  4. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley.


25940856-ldxojubx5kaly1k2zv3zks4n-2-1.gif Fig. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley

5, Disconnect the heater hose from the coolant pump.
6. Disconnect the coolant pump-to-engine hose and position aside.
7. Remove the 3 bolts from the coolant pump assembly.
8. Reposition the coolant pump-to-thermostat housing hose clamp and remove the coolant pump and hose as an assembly.


25940856-ldxojubx5kaly1k2zv3zks4n-2-3.gif
Fig. View of the water pump and related components-3.0L engine

To install:
  1. Connect the coolant pump-to-thermostat housing hose and reposition the clamp.
  2. Position the coolant pump assembly and install the 3 bolts:
    1. Tighten to 89 inch lbs. (10 Nm).
    2. Tighten the 3 bolts an additional 90 degrees.
  3. Connect the coolant pump-to-engine hose and the heater hose.
    NOTE
    Install the coolant pump drive pulley flush with the end of the camshaft.
  4. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley.



25940856-ldxojubx5kaly1k2zv3zks4n-2-6.gif Fig. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley

5. Install the coolant pump belt.
6. Fill and bleed the cooling system.

Nov 04, 2015 | 2009 Ford Fusion SE

2 Answers

Serpentine belt keeps coming off


With the belt on. Look at it inline with it. Every pulley should be inline/straight. If one is slanted just a little it will throw the belt. The only other thing would be the tensioner is bad.

Aug 06, 2014 | 2006 Ford Fusion

1 Answer

Bolt backed out of idler pulley in my 2008 ford fusion what do I need to do to put my new pulley in


You need a serpentine belt tool, you can rent one at the parts place and while you are there get the new idler. You will also need a wrench to fit the bolt. Remove the belt then take the bolt out of the idler and install the new one, you can use some low strength loctite purple to keep this from happening again. Reinstall the belt, return the tool and get your money back for the rental.

Feb 17, 2014 | 2008 Ford Fusion

1 Answer

Replace drive belt


Are you talking about the cam drive belt or the accessory drive serpentine belt? What engine, the 2.0 liter 4-cylinder, or the 2.5 liter V6? If it's the serpentine belt, does it have air conditioning?

Feb 23, 2013 | 1997 Ford Contour

1 Answer

How often should you change the sepentine belt 2005 freestar?


The belt is your accessory drive belt, no different
than the older V-Belts of the last 120 years

Nothing special ---just a belt

You replace it as you have your whole life

That may be every 6 years, if you turn it over & it
has cracks across it

There is a lot on the internet just on belts
Go to Gates or some belt mfg & educate yourself

Have no idea when a v belt left & a single flat belt
changed names, we lost the entire driving world
& now no one has heard of a serpentine belt

They have only been on vehicles for about 30 years

Oct 03, 2012 | 2005 Ford Freestar

1 Answer

How do i change my belt on my 2008 ford fusion 2.3l


Go to daycoproducts.com, they have illustrations for just about every vehicle. When you get to the Home page click on 'cars and light trucks" then on "belts" then on "serpentine belts". Then, go to the right side of the page and click on "belt routing guide" find your car, then get the illustration number. Close out that page and got "belt routing guide illustrations" go to the illustration number for your car.

Feb 01, 2011 | 2006 Ford Fusion

1 Answer

How do you install a serpentine belt on a 1999 Ford Taurus SE 3.0 v6 engine?


Go to; www.daycoproducts.com click on automotive belt, then sepentine belts then on the right side of the screen you have to click on the description of your vehicle to get the diagram number the click on diagrams and go to that number. I hope this helps you.

Jan 24, 2010 | 1999 Ford Taurus

Not finding what you are looking for?
2008 Ford Fusion 2.3 Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...