Question about Cars & Trucks

Open Question

I removed starter from grasshopper 721d and can't remember the wire connections. Need help.

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jturcotte
  • 8266 Answers

SOURCE: need wiring diagram for fender

Didn't get your model and year. The big wires go one on each side, and it doesn't really matter which side, except if there are more than 2 big wires, and extras go on the same side as the battery wire. The wire to the starter should be by itself on the solenoid terminal. The start wire from the ignition switch goes to the small "S" terminal. If there are more wires for the small terminals, I'll need to know your model and year to tell you where they go. If the car has a ballast resistor, you will have a wire from the solenoid to the ignition coil.

Posted on Jun 28, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Grasshopper 721d manual


how tight does the field assembly need t be on clutch.

Dec 09, 2011 | Cars & Trucks

1 Answer

Starter replacement


  • Check the condition of the battery. A weak battery can't turn the starter over. Make sure thesultansikand.jpg battery is at full strength before you blame the starter. Your car's instrument cluster should indicate when there is a low battery with either a warning light or ammeter.
  • Also check the battery connections, the wires going to the starter, and the starter connection. The most important wire is the big one running down the back of the battery. It is the wire that goes from the battery to the starter. All connections should be snug. Check that the insulation on the wires is intact. Tighten any connections loose enough to wiggle by hand.
  • Check the starter solenoid. The starter solenoid is a special switch that turns the starter on and off. Solenoids rarely cost more than $10, and they are fairly easy to replace. When you turn the key, have a friend listen to the solenoid for a clicking sound. If there's no sound, assume the solenoid is broken and needs to be replaced.
  • If the automotive engine is turning over and still won't start, it might be due to another problem unrelated to the starter or battery. Anything from a dirty air filter, worn spark plugs, bad spark plug wires, a worn distributor cap, insufficient fuel reaching the engine or even blown gaskets can prevent a car from starting. If you can't isolate the problem through trial and error, it may be time to take the car to a mechanic for check-up or repair.

    Once you've determined that the problem is not resolved by troubleshooting the above issues, it may very well be that you need to replace the starter.

  • Disconnect the battery cables in order to reduce the possibility of accidentally shocking yourself.
  • Remove the electrical connections from the side of the starter. There are usually two wires: a positive and a negative wire. Remove the positive wire first, and then remove the negative wire from the starter. You may want to mark the connections with a paint pen to help you correctly reconnect the connectors to their proper terminals. To remove the connections, you'll need to use an open face wrench or socket wrench to remove the bolts.
    After both of the electrical connections are removed, you'll need to unbolt the starter from the chassis. Before you remove these bolts, take note of how the starter is oriented. You may want to mark the bolts with paint pens. There are usually only two or three bolts that attach the starter to the vehicle.
  • Remove the starter. In preparation, look closely at your car and determine what path will be easiest for removing the starter. It might be a tight fit, but you'll need to twist and pull the starter around various engine and frame parts in order to get it out of the car. Some cars may be particularly tight, especially those with front wheel drive. You may have to remove other parts in order to get enough space the pull the starter out. If you do remove engine parts, take care to remember their proper location. Replace bolts into the same place they came from once you pull a piece off. This will help you keep up with all of the pieces.
  • Once you've pulled the starter out, you can put the new starter in its place. You'll need to put it back in the exact same way you pulled the old starter out. Once you have it in place, put in a bolt just enough to hold the starter in place. Then connect the electrical connections beginning with the ground wire. Once the ground wire is connected, attach the rest of the wiring. Next, install the rest of the bolts holding the starter to the frame. Check to see that all bolts are tight.

Jul 06, 2011 | Ford E-350 Super Duty Cars & Trucks

1 Answer

Removing a starter from a 94 new yorker


  • Check the condition of the battery. A weak battery can't turn the starter over. Make sure the battery is at full strength before you blame the starter. Your car's instrument cluster should indicate when there is a low battery with either a warning light or ammeter.
  • Also check the battery connections, the wires going to the starter, and the starter connection. The most important wire is the big one running down the back of the battery. It is the wire that goes from the battery to the starter. All connections should be snug. Check that the insulation on the wires is intact. Tighten any connections loose enough to wiggle by hand.
  • Check the starter solenoid. The starter solenoid is a special switch that turns the starter on and off. Solenoids rarely cost more than $10, and they are fairly easy to replace. When you turn the key, have a friend listen to the solenoid for a clicking sound. If there's no sound, assume the solenoid is broken and needs to be replaced.
  • If the automotive engine is turning over and still won't start, it might be due to another problem unrelated to the starter or battery. Anything from a dirty air filter, worn spark plugs, bad spark plug wires, a worn distributor cap, insufficient fuel reaching the engine or even blown gaskets can prevent a car from starting. If you can't isolate the problem through trial and error, it may be time to take the car to a mechanic for check-up or repair.

Once you've determined that the problem is not resolved by troubleshooting the above issues, it may very well be that you need to replace the starter.

  1. Disconnect the battery cables in order to reduce the possibility of accidentally shocking yourself.



    #block-google_admanager-1 { margin-left: -22px; }
  2. Remove the electrical connections from the side of the starter. There are usually two wires: a positive and a negative wire. Remove the positive wire first, and then remove the negative wire from the starter. You may want to mark the connections with a paint pen to help you correctly reconnect the connectors to their proper terminals. To remove the connections, you'll need to use an open face wrench or socket wrench to remove the bolts.
    After both of the electrical connections are removed, you'll need to unbolt the starter from the chassis. Before you remove these bolts, take note of how the starter is oriented. You may want to mark the bolts with paint pens. There are usually only two or three bolts that attach the starter to the vehicle.
  3. Remove the starter. In preparation, look closely at your car and determine what path will be easiest for removing the starter. It might be a tight fit, but you'll need to twist and pull the starter around various engine and frame parts in order to get it out of the car. Some cars may be particularly tight, especially those with front wheel drive. You may have to remove other parts in order to get enough space the pull the starter out. If you do remove engine parts, take care to remember their proper location. Replace bolts into the same place they came from once you pull a piece off. This will help you keep up with all of the pieces.
  4. Once you've pulled the starter out, you can put the new starter in its place. You'll need to put it back in the exact same way you pulled the old starter out. Once you have it in place, put in a bolt just enough to hold the starter in place. Then connect the electrical connections beginning with the ground wire. Once the ground wire is connected, attach the rest of the wiring. Next, install the rest of the bolts holding the starter to the frame. Check to see that all bolts are tight.

Dec 10, 2010 | 1994 Chrysler New Yorker

2 Answers

How to take out the starter


Chrysler Caravan/Voyager/Town and Country 1996-1999 Starter - REMOVAL & INSTALLATION(see Figures 7, 8, 9, 10 and 11)

7d28ee2.jpg

Fig. 7: Disengage the solenoid wiring connector, then the battery positive (B+) nut and wire from the starter motor

ac6bf44.jpg

Fig. 8: Remove the 3 starter motor-to-transaxle bellhousing mounting bolts

1d4f6fd.jpg

Fig. 9: Remove the starter motor from the vehicle

d9e9e14.jpg

Fig. 10: After removing the starter motor, examine the teeth of the flywheel for excessive wear or damage. Repair if necessary

b56ba8b.jpg

Fig. 11: If the old starter is going to be re-installed, check the condition of the pinion gear teeth. Replace the starter if the pinion gear shows excessive wear or damage
  1. Disconnect the negative battery cable.
  2. Raise and safely support the front of the vehicle securely on jackstands.
  3. Disengage the solenoid wiring connector from the terminal. This connection may be held in place by a retaining nut, or it could be a push-in connector.
  4. Remove the B+ nut and wire from the starter motor terminal.
  5. Remove the starter motor-to-transaxle bellhousing mounting bolts.
  6. Remove the starter from the vehicle. If equipped, remove the starter motor spacer.
To install:
  1. If equipped, hold the starter motor spacer in position.
  2. Install the starter motor into position on the vehicle.
  3. Install the starter motor-to-transaxle bellhousing mounting bolts. Tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  4. Engage the solenoid wiring connector onto the starter terminal.
  5. Connect the B+ wire and tighten the retaining nut to 90 inch lbs. (10 Nm).
  6. Lower the vehicle.
  7. Connect the negative battery cable.
  8. Verify starter motor operation.

Hope this help (remember comment and rated this).

Apr 20, 2010 | 1996 Dodge Caravan

1 Answer

Where is starter on 2002 honda crv?


Honda_Cr-V_2001-2006
Starter - Removal & Installation

2.0L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Starter wiring harness connectors Starter motor

To install:
  1. Install or connect the following:

    Starter motor. Tighten the bolts to 33 ft. lbs. (44 Nm). Starter wiring harness connectors. Tighten the battery cable nut to 79 inch lbs. (9 Nm). Negative battery cable

2.4L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Knock sensor connector Starter wiring harness connectors Starter motor

    8b26da5.jpg
    Fig. Starter mounting

To install:
Install or connect the following:

Starter motor. Tighten the upper bolt to 33 ft. lbs. (44 Nm); the lower bolt to 47 ft. lbs. (64 Nm). Starter wiring harness connectors. Tighten the battery cable nut to 84 inch lbs. (9 Nm). Knock sensor connector Negative battery cable


Hope this help (remember comment and rated this).

Apr 04, 2010 | 2002 Honda CR-V

1 Answer

How to replace the starter


Toyota Celica, Corolla, ECHO & MR2 1999-05
Starter - Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Radiator upper support seal
Air cleaner
Engine under covers
Starter wiring
Starter

3. Installation is the reverse of removal. Torque the bolts to 28 ft. lbs. (37 Nm). Note that the bolts are 2 different lengths.


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Battery and tray. On models equipped with an air bag, work must NOT be started until at least 90 seconds have passed from the time that both the ignition switch is turned to the LOCK position and the negative cable is disconnected from the battery.
Coolant reservoir
Reservoir hose from the radiator
Right side under cover
Wiring clamp
Wiring from the starter
Starter


To install:
1. Install or connect the following:
Starter
Starter wiring and nut
Starter connector and wire clamp
Right side engine cover
Radiator reservoir and hose
Battery and tray

2. Check the cooling system and top off if necessary.


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Negative battery cable. On models equipped with an air bag, work must NOT be started until at least 90 seconds have passed from the time that both the ignition switch is turned to the LOCK position and the negative cable is disconnected from the battery
Engine under covers
Wiring from the starter terminals
Starter mounting bolts
Starter


To install:
1. Install or connect the following:
Starter
Starter wiring
Engine under covers


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Negative battery cable
Front engine undercover
Starter wiring harness connectors
Starter mounting bolts
Starter motor


To install:
1. Install or connect the following:
Starter motor. Tighten the bolts to 28 ft. lbs. (37 Nm).
Starter wiring harness connectors
Front engine undercover
Negative battery cable

Hope help with this (remember rated and comment).

Mar 11, 2010 | 2003 Toyota Corolla

1 Answer

Where is starter located and how to remove it , for a dodge caravan 1998,3.3l


Starter - Removal & installing
  1. Disconnect the negative battery cable.
  2. Raise and safely support the front of the vehicle securely on jackstands.
  3. Disengage the solenoid wiring connector from the terminal. This connection may be held in place by a retaining nut, or it could be a push-in connector.
  4. Remove the B+ nut and wire from the starter motor terminal.
  5. Remove the starter motor-to-transaxle bellhousing mounting bolts.
  6. Remove the starter from the vehicle. If equipped, remove the starter motor spacer.
To install:
  1. If equipped, hold the starter motor spacer in position.
  2. Install the starter motor into position on the vehicle.
  3. Install the starter motor-to-transaxle bellhousing mounting bolts. Tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  4. Engage the solenoid wiring connector onto the starter terminal.
  5. Connect the B+ wire and tighten the retaining nut to 90 inch lbs. (10 Nm).
  6. Lower the vehicle.
  7. Connect the negative battery cable.
  8. Verify starter motor operation.
020fef8.jpg

Disengage the solenoid wiring connector, then the battery positive (B+) nut and wire from the starter motor

98933b2.jpg

Remove the 3 starter motor-to-transaxle bellhousing mounting bolts

e2afde4.jpg

Remove the starter motor from the vehicle


The starter relay is located in the Power Distribution Center (PDC) in the engine compartment. Refer to the underside of the PDC cover for starter relay location.

Hope helped with this (remember rated this help) Good luck.

Nov 18, 2009 | 1998 Dodge Grand Caravan

1 Answer

Need to know how to remove starter from 1991 dodge caravan


e
26065b4.jpg

Starter motor mounting-2.2L and 2.5L engines

- Working from under the vehicle, disconnect the starter motor heat shield clamp

fb70ec4.jpg

View of the starter motor with the heat shield removed while looking over the crossmember

-
Removing the starter motor mounting stud nut where the air pump tube bracket is also attached

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle. The starter can be removed by reaching over the crossmember.
  3. Remove the heat shield and its clamps, if so equipped.
  4. On the 2.2L and 2.5L engines, loosen the air pump tube at the exhaust manifold and move the tube bracket away from the starter.
  5. Remove the electrical connections from the starter.
  6. Remove the bolts attaching the starter to the flywheel housing and the rear bracket to the engine or transaxle.
  7. Remove the starter from the engine.

To install:
  1. Position the replacement starter against the mounting surface.
  2. Install the mounting bolts.
  3. Connect the starter wiring.
  4. On 2.2L and 2.5L engines, position the air pump tube toward the starter, then connect the tube bracket to the exhaust manifold.
  5. Install the heat shield and clamp.
  6. Connect the negative battery cable.

Hope helped with this (remember rated this help) Good luck.

Nov 03, 2009 | 1991 Dodge Caravan

1 Answer

Remove a starter form a 98 s-10


1. open hood
2. remove batt. cables
3.remove batt. cable on starter
starter is located lower pass. side of motor
(also might be a couple of other wires connected to the starter remove them as well & remember their locations).
4. remove two bolts that mount the starter to the trans. bell housing. and remove starter
5. install new starter and hook wires up with the batt. last.

Jan 12, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

I have a grand marquis 1993 and the car wouldnt start although the batteries r good i was told by a mechanic it is the starter . I need to know can I replace the starter by myself and what do i need to do...


I would always suggest having a mechanic do things first and only try yourself if you think you can do it and you do not have the money for a mechanic that can give you a warranty.

Disconnect the battery cables in order to reduce the possibility of accidentally shocking yourself.

Remove the electrical connections from the side of the starter. There are usually two wires: a positive and a negative wire. Remove the positive wire first, and then remove the negative wire from the starter. You may want to mark the connections with a paint pen to help you correctly reconnect the connectors to their proper terminals. To remove the connections, you'll need to use an open face wrench or socket wrench to remove the bolts.
After both of the electrical connections are removed, you'll need to unbolt the starter from the chassis. Before you remove these bolts, take note of how the starter is oriented. You may want to mark the bolts with paint pens. There are usually only two or three bolts that attach the starter to the vehicle.

Remove the starter. In preparation, look closely at your car and determine what path will be easiest for removing the starter. It might be a tight fit, but you'll need to twist and pull the starter around various engine and frame parts in order to get it out of the car. Some cars may be particularly tight, especially those with front wheel drive. You may have to remove other parts in order to get enough space the pull the starter out. If you do remove engine parts, take care to remember their proper location. Replace bolts into the same place they came from once you pull a piece off. This will help you keep up with all of the pieces.

Once you've pulled the starter out, you can put the new starter in its place. You'll need to put it back in the exact same way you pulled the old starter out. Once you have it in place, put in a bolt just enough to hold the starter in place. Then connect the electrical connections beginning with the ground wire. Once the ground wire is connected, attach the rest of the wiring. Next, install the rest of the bolts holding the starter to the frame. Check to see that all bolts are tight.

Dec 18, 2008 | 1993 Mercury Grand Marquis

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...