Question about 2002 Hyundai XG350

Open Question

Ets relay location 2002 hyundia xg-350

Relay location

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
ghost4548
  • 776 Answers

SOURCE: ac compressor will not engage 2003 hyundai xg 350

You found the problem (lost ground on relay)... Fix it! You solve this problem yourself.

Posted on Jun 02, 2009

Ad
ghost4548
  • 776 Answers

SOURCE: Front wheel stud broke off

Knuckle needs to be removed and the center hub 'pressed out' using a hydraulic press (accepted procedure). You can avoid this by using an air hammer and disk cutting tool to remove the old stud, then trim the 'stop flange' on the new stud (1/4 moon cut) in order to install it.... however, you gotta know what you're doing so you don't compromise the integrity of the new stud.

Posted on Jul 04, 2009

  • 1 Answer

SOURCE: How do you get to the rear plugs on a XG 350, 2002

Yes you need to pull the manfold to replace the back three plugs. No you do not have to drain water or oil. Use a good double platum plug. While your there replace the three wires. You do not need any gaskets if your cearfull. Good luck

Posted on Aug 11, 2009

Testimonial: "it's not a hard job if you have the correct tools and make all the hoses, it is just very time wise 2.5 hours taking your time not to do any damage"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Camshaft sesor location hyudia xg 350


no year, azera? why not name car?????
?
always on the the end of the cam.
but on a Toyota, XG 350, not a clue..... read blue box above,. ugh !
i will not do posts , no year, and get funky no country.. for most.
dig,dig ,bam
XG350 name was used as of 2002 to reflect the new 3.5 L version of the Sigma V6.
ok the 3.5L
i looked online and 9 engines, shows CMP but not 3.5L

autozoned
"On the 3.5L engine, the sensor is located at the front of the engine near the camshaft gear."
this engine has VVT with 2 sensors and 2 vvt solenoids
finding the real CMP is hard. sure.
part 39318 CMP
it exactly here, so you can find any part ad Hyundai. just look


http://www.jimellishyundaiparts.com/images/parts/Hyundai/fullsize/HMA3L0PA0520-21104.jpg

clear huh?
this is best covered with a REAL FSM
and if PCM is throwing codes, do not assume this part is bad
they rarely go bad... instead post the code. DTC.

what if the chain was loose. the sensor will read wrong,
just one lil, example.

Jan 23, 2014 | Toyota Tacoma Cars & Trucks

2 Answers

2002 Hyundia Santa Fe headlight relay


I would want to check for a loose ground wire first. Fuses must be okay if the lights work "at times" correctly.

Sep 24, 2013 | 2002 Hyundai Santa Fe

1 Answer

What does code P1154 mean on a hyundia sontona 2002


You sure that's the right number?
For Hyundai, it shows codes 1151 and 1155, both referring to the electronic throttle system (ETS). I did not find a code P1154.

P1151: ETS Main Accel Position Sensor 2 Malfunction.
P1155: ETS Limp Home Valve.
P1174: Electronic Throttle System #1 Close Malfunction.

Dec 16, 2011 | Hyundai Cars & Trucks

1 Answer

9@how to fix dtc p1178 and p1118 on a 2002 hyundai xg350


I live in Australia & have a Hyundai Grandeur XG 3LT V6 2002 model (US equivalent is Hyundai XG300).
Fault codes are P1118 (ETS motor fault) & P1178 (ETS motor battery voltage open). An intermittent fault.
The first code denotes general area of the fault & the second code denotes the specific fault.
So the specific fault is that the ETS-PCM computer is not receiving 12V on pin 2 with ignition on.
'Check engine' light remains on & car is in 'limp home mode' with very little power & poor performance.
I had purchased the Hyundai service manual online (ebook about $8) for the US model. Could not find any
manual for the Australian model. On page FLA-52 found the block diagram for the whole ETS system.
I am a retired electrical engineer so now it became easier for me to find the fault.
There are 2 computers behind the center console. PCM & ETS-PCM.
Pin 2 of the ETS-PCM should have 12V present when ignition is on.
In fault mode 12V was not present. This 12V is supplied from ETS 15A fuse (fuse box under dashboard)
via a relay (i will call this relay the ETS relay). The 15A fuse was OK but the 12V was only
intermittently being passed through the relay points. Relay is located near ignition switch on a
sub panel which has about 6 relays on it. ETS relay was at right bottom corner of sub panel.
Yellow wire feeds the 12V (which is always present even with ign. switch off) to the relay points.
White wire is the output wire from the relay points which feeds 12V to pin 2 of the ETS-PCM computer.
Measure if 12V is present at white wire when ign. switch is turned on (no need to start engine)
I only had the 12V present intermittently. So pulled out the ETS relay - tested contacts with
ohmmeter & found to be only making contact intermittently when relay lever depressed
- removed relay case by grinding away one corner of the case - cleaned the relay points with fine sandpaper.
replaced the relay case & taped with black insulating tape to keep out dust. Tested relay with ohmmeter & points
now OK. Fault is now cleared & car is operating normally.
Also had previously purchased on Ebay a Can OBD11 scanner for $15 which read the fault codes OK.
Hope this helps other people with similar problem.

Mar 15, 2011 | Hyundai Motor 2003 XG350

2 Answers

Need to know what these code means p1118,p1110,p1178


Hi Friend:

In checking your Codes heres the Data.

#1) P1118 -->> this code is sending a signal that your ETCS =Throttle Motor is Either Damaged or it has Failed.

#2) P1110-->> this code is showing that your PCM (Control Module) has received a Signal that your you have a problem with your Throttle Body.

#3) P1178-->> this Code is Indicating that Your Electronic Throttle Motor Battery has a Open Circuit.

Sir, I would start checking your Fuses before you Spend a Bunch of Uneccessary money. It could be that your ETCS Fuse is blown, This could be causing All these Codes.but theres is still a chance that you'll get a Code after changing the ETCS Fuse.

Note: you have Fuse Blocks inside your Vehicle and Under your Hood as well, They'll be Labelled Fuses and Relays.

I hope this Fuse solves ALL your Problems sir.Please let me know how my Solution has helped you by Voting for me and a Testamony would be Appreciated.

Thank You for Using FixYa From: d_hubbs

Aug 17, 2010 | 2004 Hyundai Santa Fe

1 Answer

Need to locate spark plugs on 2004 hyudai xg 350 6 cyl 3.5


once you remove the engine cover, on each valve cover you will see coil packs. remove these coil packs and right underneath are the spark plugs. replace with either ngk or nippondenso. happy holidays

Dec 30, 2009 | 2002 Hyundai XG350

1 Answer

2002 XG 350. License plate bulb out. How do I pull bulb, wiring is too tight. Thanks Joe B


2002 HYUNDIA XL 350, LIC. PLATE BLUBS CAN NOT GET ASSEMBLY DOWN TO REPLACE BLUBS, DUE TO THE FACT THE WIRES ARE TOO SHORT TO PULL UNIT DOWN. ANYH IDEAS?

Oct 30, 2009 | 2002 Hyundai XG350

1 Answer

Front wheel stud broke off


Knuckle needs to be removed and the center hub 'pressed out' using a hydraulic press (accepted procedure). You can avoid this by using an air hammer and disk cutting tool to remove the old stud, then trim the 'stop flange' on the new stud (1/4 moon cut) in order to install it.... however, you gotta know what you're doing so you don't compromise the integrity of the new stud.

Jul 04, 2009 | 2002 Hyundai XG350

1 Answer

Ac compressor will not engage 2003 hyundai xg 350


You found the problem (lost ground on relay)... Fix it! You solve this problem yourself.

May 02, 2009 | 2002 Hyundai XG350

Not finding what you are looking for?
2002 Hyundai XG350 Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...