Question about 2000 GMC New Sierra 1500

Open Question

What r torque cylinder head torque specs and tightening sequence on a 2000 gmc sierra 5.3 liter

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 115 Answers

SOURCE: head bolt torque settings for a 1998 gmc 1500 5.o

Cylinder Head Torque
1st - step, all bolts; - 22 ft./lbs. 2nd - step, long bolts; - turn 75 degrees 3rd - step, medium bolts; - turn 65 degrees 4th - step, short bolts; - turn 55 degrees fig121.png

Posted on Sep 04, 2009

Testimonial: "Thank you this was excellent straight to the point & easy !!!"

Ad
  • 231 Answers

SOURCE: Heads

here is the sequence pay close attention to the numbers in the brackets

(8) (5) (9)
(12) (4) (1) (13)
(11) (7) (3) (2) (6) (10)

Note : 12 and 11 are at the vey front of the vehicle:
the torque sequence is as follows
step 1) torque all bolts to 22 foot pounds
step 2) turn bolts as follows
short bolts an additional 55 degrees
medium bolts an aditionl 65 degrees
long bolts an additional 75 degrees

Posted on Oct 15, 2008

ZJLimited
  • 17970 Answers

SOURCE: need to locate fuel filer on 2000 gmc sierra truck

For 2000 GMC Truck Sierra 2500 4WD 5.3L SFI 8cyl the Fuel Filter is located: Under vehicle, driver side, below seating area, near fuel tank, mounted on frame rail in fuel line.

bb521df.jpg

Fig. Typical in-line fuel filter mounting location

Hope this help (remember comment and rated this post).

Posted on Apr 19, 2010

  • 89 Answers

SOURCE: 1989 gmc sierra 6.2 liter diesel hard start when hot

hi, i have seen this problem ten years ago twice, but i was dumbfounded by the answer. all details aside, I replaced the ecm, and never had the problem again with both of them. this repair was a recommended repair by the local truck depot in my town, they stated the ecm got hot along with the truck and it lost the injector sensor signal. now, don't take this solution and run with it, i haven't repaired a 6.2 diesel in ten years and i maybe off track completely. but at least maybe you could ask around your town or maybe a large truck facility about this. of course, you should take to a shop to have diagnosed. hope i could help.

Posted on Jun 07, 2010

  • 335 Answers

SOURCE: How do i put a new ac belt on for a 2000 gmc

Hello, this is the instructions for replacing the a/c belt.

  • Remove the accessory drive belt.







  • d7251da.gif
  • Rotate the air conditioning (A/C) drive belt tensioner clockwise in order to relieve the belt tension.
  • Remove the A/C drive belt.59d2902.gif
  • Posted on Jun 15, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


    Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
    1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
    2. Step 2: Bolts 1-10 verify torque without loosening
    3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
    4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
    5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


    26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

    Dec 10, 2015 | Dodge Cars & Trucks

    1 Answer

    Need head bolt torque specs for a 1996 saturn sl


    Quote:





    Originally Posted by norvelplagbao52

    1993 saturn sl2 1.9 dohc cylinder head torque
    specs and sequence
    Cylinder head bolt
    tightening procedure:
    CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

    INTAKE
    SIDE
    8 4 1 5 9

    7 3 2 6 10
    EXHAUST SIDE

    In sequence,
    torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
    In sequence,
    torque all bolts. Torque: 50 Nm (37 ft-lbs)
    In sequence, turn each bolt an
    additional 90 degrees.





    Originally Posted by norvelplagbao52

    1993 saturn sl2 1.9 dohc cylinder head torque
    specs and sequence
    Cylinder head bolt
    tightening procedure:
    CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

    INTAKE
    SIDE
    8 4 1 5 9

    7 3 2 6 10
    EXHAUST SIDE

    In sequence,
    torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
    In sequence,
    torque all bolts. Torque: 50 Nm (37 ft-lbs)
    In sequence, turn each bolt an
    additional 90 degrees.

    Sep 19, 2013 | 1996 Saturn SL

    1 Answer

    What r the torque specifications on installing a head on 2000 sierra 5.3 and the tightening sequence


    You must use new bolts, failure to do so will result in redoing the job.

    Tightening sequences
    intakes side 15 13 11 12 14
    center 10 3 1 5 9
    exhaust side 7 6 2 4 8

    Step 1
    all 11mm bolts 22 ft lbs
    Step 2
    all 11mm bolts turn add 90deg
    Step 3
    11mm bolts 1-8 turn add 90 deg
    11mm bolts 9 and 10 turn add 50deg
    Step 4
    all 8mm bolts 22 ft lbs

    Oct 24, 2012 | 1999 GMC Yukon Denali

    1 Answer

    I need to find the torque specs for the connecting piston rod? also the sequence and torque for the cylinder head bolts this is for a kia rio 2004 6cyl


    22 - 24 ft. lbs. for the rod caps and....
    110795143Cylinder Head Tightening Torque and Sequence.

    Tighten cylinder head bolts in order shown.
    Tightening torque: 36.1 ft. lbs. (49 Nm, 5 kg-m)

    Loosen bolts in reverse of order shown.

    Retighten cylinder head bolts in order shown.
    Tightening torque: 18 ft. lbs. (25 Nm, 2.5 kg-m)

    Mark cylinder head bolts for rotational reference.
    Rotate cylinder head bolts 90°(1/4 Turn) in order shown.

    CAUTION:
    • Do not reuse the old cylinder head bolts.

    May 31, 2010 | 2004 Kia Rio

    1 Answer

    What is the right Torque Specification of the cylinder head bolt,main bearing and connecting rod bearing for a 1997 Ford F 150 4.2 liter? Thank you...


    Cylinder heat bolt torque:
    Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
    Main bearing torque:
    Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
    Connecting rod torque:
    Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

    May 17, 2010 | 1997 Ford F150 Regular Cab

    1 Answer

    Torque specs for cylinder head on a 200 ford focus with 2.0 ltr single overhead cam. and for connecting rod... Thank you much.


    1. CAUTION: Always install new cylinder head bolts. NOTE: Lubricate the cylinder head bolts with Super Premium 5W 30 SAE X0-5W 30-QSP or equivalent meeting Ford specification WSS-M2C153-G prior to installation. Install the cylinder head assembly and tighten the cylinder head bolts in the following sequence.
    1. Tighten all bolts in a single sequence to 50 Nm
    2. Back the bolts off 1/2 turn.
    3. Tighten the bolts in sequence shown to 50 Nm .
    4. Rotate all the bolts in a single sequence an additional 180 degrees in two steps of 90 degrees each.
    9 3 1 5 7
    8 6 2 4 10 sequence for head


    Spec for rod 38Nm

    May 07, 2010 | 2000 Ford Focus

    1 Answer

    Head tourqe specs for 403 olds and bolt tightening


    Fig. : Cylinder head torque sequence, 260, 307, 350 403 Oldsmobile built engines

    5c04c01.jpg


    On the V8, tighten the bolts, in the sequence illustrated, to 100 ft. lbs. When all bolts have been tightened to this figure, begin the tightening sequence again, and torque all bolts to 130 ft. lbs.

    On V6's, tighten all head bolts in sequence to the following torques:
    * All except bolts 5, 6, 11, 12, 13 and 14 - 100 ft. lbs.(19-135.5 Nm)
    * Bolts 5, 6, 11, 12, 13, and 14 - 41 ft. lbs. (19-55.5 Nm)
    * All bolts except 5, 6, 11, 12, 13, and 14 - 142 ft. lbs. (19-192.5 Nm)
    * Bolts 5, 6, 11, 12, 13, and 14 - 59 ft. lbs. (19-80 Nm)

    9fb545e.jpg

    Hope this help (remember comment and rated this).

    Mar 29, 2010 | 1984 Oldsmobile Cutlass

    1 Answer

    What is the cylinder head torque spec for a 2005 nissan sentra 1.8 liter engine


    1. For 1.8L engines, tighten the bolts in sequence, as follows:
      1. Step 1: Bolts 1-10 to 22 ft. lbs. (29 Nm).
      2. Step 2: Bolts 1-10 to 43 ft. lbs. (59 Nm).
      3. Step 3: Loosen bolts 1-10 completely.
      4. Step 4: Bolts 1-10 to 22 ft. lbs. (29 Nm).
      5. Step 5: Bolts 1-10 plus 50-55 degrees.
      6. Step 5: Bolts 11-14 to 74 inch lbs. (8 Nm).

        0900c152801afb79.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Cylinder head torque sequence-1.8L engine


        0900c152801afad8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Tighten the valve cover bolts in sequence-1.6L and 1.8L engines

    Nov 13, 2009 | 2005 Nissan Sentra

    1 Answer

    Need cylinder head gasket torque specs.


    looks like there is special sequence to reassemble and tightening, a quick note replace any bolts that have two punch marks.tighten as follows: x x x x x 10 4 2 6 8 x x x x x 7 5 1 3 9 torque all down to 15 ft lbs torque to 30 ft lbs plus 90 degrees. Good luck!

    Sep 18, 2009 | 2000 Ford Focus

    2 Answers

    Need to know cylinder head bolt torque specs


    Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

    Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    154 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts

    yadayada
    yadayada

    Level 3 Expert

    76691 Answers

    Freddy

    Level 3 Expert

    1311 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...