Question about 2001 Nissan Micra

Open Question

Front wheel bearings on nissan micra

Front wheel bearing

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 24 Answers

SOURCE: replace front wheel bearings

The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

On a scale of 1-10 difficulty, Id rate it a strong 7

Posted on Jun 20, 2008

kaokensho
  • 2 Answers

SOURCE: how to replace front wheel

I can tell you on a 93 Altima that you have remove the entire wheel knuckle and press it out from the rear. Yeah, the knuckle, remove the strut tower bolts, drive train ( which can be lighty pressed out ), caliper and bracket, and remove the ball joint. There's a snap ring at the back of the wheel knuckle that holds the bearing, then press it out with a socket and a table vice or something to that effect. By the way the going commercial rate if you take it to a shop and have them do it starts at $150 for labor. Worth it, oh yeah.

Posted on Aug 15, 2008

  • 95 Answers

SOURCE: nissan sentra gxe 03 rear wheel hub bearing problem

Easy job ! just rem to get a gear puller for the antilock gear and install same as came off old one Parts around 100$ each apx 1/2 hr each side

Posted on Oct 15, 2008

  • 35 Answers

SOURCE: how do you change rear wheel bearing on a 2004 nissan sentra

Yes it is as easy as it looks. If you had the tire off and figured out that it looks easy, you shouldn't have much problem.

Posted on Mar 21, 2009

  • 40 Answers

SOURCE: Step by step on how to replace front wheel bearing

Raise vehicle, remove wheel, remove brake caliper, remove brake rotor remove steering knuckle by disconnecting the tie rod, ball joint, and strut. press out hub, remove snap rings press out bearing. Reassemble in reverse order.

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I change rear wheel bearing on 2009 k12 nissan micra


That should be in the service manual: You can search for one using Google and this in the search box: "2009 k12 nissan micra service manual" without the quotes, it should show a lot of different sources for one.

Nov 28, 2014 | Nissan Cars & Trucks

1 Answer

1986 nissan pathfinder


Hi Melissa,here's a guide to your front wheel bearings.

Feb 11, 2013 | 1997 Nissan Pathfinder

1 Answer

Is the front wheel bearing to a 2004 nissan murano pressured


if your asking whether or not it is a pressed in bearing or a bolt in bearing, it is a pressed in bearing. The knuckle will need to be removed and brought to a shop to have the bearing pressed in and out. It is not unusual for the hub (the part that has the wheel studs in it) to be bad as well.

Nov 28, 2010 | 2004 Nissan Murano

1 Answer

Directions replace front wheel bearings on a 1985 nissan stanza?


996fb79.gif

NOTE: After the wheel bearings have been removed or replaced or the front axle has been reassembled be sure to adjust wheel bearing preload. Refer to the Adjustment service procedure below. On the 1989–92 240SX there is just one wheel bearing, pressed into the hub and no adjusting cap. Refer to the exploded views of the Front Axle Hub Assembly. Review the complete service procedure.
  1. Raise and support the vehicle safely.
  2. Remove the front wheels and the brake caliper assemblies. NOTE: Brake hoses do not need to be disconnected from the brake caliper assemblies. Make sure the brake hoses are secure and do not let caliper assemblies hang unsupported from the vehicle.
  3. Work off center hub cap by using thin tool. If necessary tap around it with a soft hammer while removing.
  4. Pry off cotter pin and take out adjusting cap and wheel bearing lock nut.
  5. Remove wheel hub with disc brake rotor from spindle with bearings installed. Remove the outer bearing from the hub.
  6. Remove inner bearing and grease seal from hub using long brass drift pin or equivalent.
  7. If it is necessary to replace the bearing outer races, drive them out of the hub with a brass drift pin and mallet.
  8. Install the outer bearing race with a tool (KV401021S0 special tool number) until it seats in the hub flush. NOTE: Place a large glob of grease into the palm of one hand and push the bearing through it with a sliding motion. The grease must be forced through the side of the bearing and in between each roller. Continue until the grease begins to ooze out the other side through the gaps between the rollers. The bearing must be completely packed with grease.
  9. Pack each wheel bearing with high temperature wheel bearing grease. Pack hub and hub cap with the recommended wheel bearing grease up to shaded portions. Refer to the illustration.
  10. Install the inner bearing and grease seal in the proper position in the hub.
  11. Install the wheel hub with disc brake rotor to the spindle.
  12. Install the outer wheel bearing, lock washer, wheel bearing lock nut, adjusting cap, cotter pin (always use a new cotter pin and O-ring for installation after adjustment), spread cotter pin then install the O-ring and dust cap.
  13. Install the brake caliper assemblies and bleed brakes if necessary. Install the front wheels.

Jun 23, 2009 | 1985 Nissan Stanza

3 Answers

How do you change rear wheel bearing on a 2004 nissan sentra


Yes it is as easy as it looks. If you had the tire off and figured out that it looks easy, you shouldn't have much problem.

Mar 21, 2009 | 2002 Nissan Sentra

1 Answer

How to replace front wheel bearings in 2006 nissan sentra


hi..check on the following link to replace the
wheel bearings.
http://autorepair.about.com/od/fixityourself/ss/wh_bearing_old.htm
check it out..
thank u..
rate me..

Mar 06, 2009 | 2006 Nissan Sentra

2 Answers

Humming


It may be the bearing. located underneath the wheel rotor on the wheel axle. Lift up the car and remove the wheel, brake pads and rotor. remove the rotor and turn the nut that holds to axle in place by removing a small pin. (if there is one) and turning counter clockwise. you will see the bearing under the rotor. Check for missing bearings , dirty oil debris, etc. If it has any of this , replace with new bearing. The exact way you removed it. Do not overtighten the nut. This will cause the bearing to overheat. just tighten enough for the bearing to fit snug with no movement.Make sure you grease up the new bearing good.

Dec 16, 2008 | 2003 Nissan Altima

2 Answers

Nissan sentra gxe 03 rear wheel hub bearing problem


Easy job ! just rem to get a gear puller for the antilock gear and install same as came off old one Parts around 100$ each apx 1/2 hr each side

Jun 12, 2008 | 2003 Nissan Sentra

Not finding what you are looking for?
2001 Nissan Micra Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...