Cars & Trucks Logo

Related Topics:

A
Anonymous Posted on Oct 24, 2012

Wind screen wipers not working on ford bantum 2010

5 Related Answers

Anonymous

  • 426 Answers
  • Posted on Dec 08, 2008

SOURCE: Ford Taurus 1996-wind screen water squirter not working

You will need a test light/probe to check wether you have power to the windscreen washer bottle motor.If you have power at the motor and it doesnt pump you will need to replace it.Because the wipers are still working its unlikely to be a power supply issue.Can you hear the motor trying to pump when you activate it?If you can hear motor humming then you may have blocked nozzles.Usualy a small sewing needle poked down the squirter nozzles will clear them.Also make sure your water squirter hoses are not blocked and havnt fallen off.

Ad
alicantecoli

Colin Stickland

  • 22516 Answers
  • Posted on Jan 07, 2010

SOURCE: my screen wash is not working nor wipers. When I

think you need a new control switch mechanism

johnjohn2

Johnny Brown

  • 5763 Answers
  • Posted on Oct 29, 2010

SOURCE: Wind screen wipers and central

you may have two problems or they are both related, the first step would be to check all your fuses, then if fuses are good then test for power at motor to see if the motor is bad or the switch, you will need a test light to do this, turn power on to wipers and then test for power at motor.

Anonymous

  • 1 Answer
  • Posted on Feb 08, 2011

SOURCE: wind screen wipers not working

fuse number F56
mine have also stopped working and the fuse is fine!

fordexpert

  • 5692 Answers
  • Posted on May 16, 2012

SOURCE: Front wind shield wipers not turning off

This can be a problem with the multifunction stick switch by the column or the motor has a bad ground wire or internal contact.

What happens inside the wiper motor is that a contact point shifts the revolving mechanism into the Park or Rest position. If the contact point fails to work and derail the revolving mechanism, it will never stop.

Sometimes a bad ground wire or the casing will corrode and the contact wire inside the motor will not work.

The stalk switch is another problem. There is just too much going on inside this thing to be dependable. It in effect, it can fail to register your turning off the wiper motor. So it stays on even though it is turned off.

Both of these parts connect to each other. You can get wiring diagrams at Autozone.com by registering your car for free. If you can find the wires on the motor connector, you should be able to tell whether the stalk switch is shutting off by using a voltmeter.

If you can tell the stalk is good, then the only thing left is the wiper motor.

With the wiring diagrams and also fusebox layouts you get from Autozone, you can find the correct fuse to pull on the wiper motor circuit.
This is a temporary solution and sometimes the radio or other things like a domelight are attached to the same fuse.

I hope my solution is helpful.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How can I fit a b3 1.3l engine in a rocam 1.3l bantum

I'm not sure about the specifics of fitting a B3 1.3L engine in a Rocam 1.3L Bantum. However, I found a performance kit that is designed specifically for the Ford Rocam 1.3L engine. The kit includes a 4-2-1 performance exhaust manifold, a performance camshaft, and a recalibrated computer1. The kit is designed to deliver stunning all-round performance and economy, and it can increase the power output of a 1.3L Ford Ka from 51 kW to 66 kW (90 horsepower) with torque increases from 110 Nm to 122 Nm from as low as 2000 RPM.

If you're looking to fit a B3 1.3L engine in a Rocam 1.3L Bantum, you could consider purchasing the ST90 performance kit for your Bantum 1.3L. The kit is designed to make the same power as a 1.6L Bantum and can be easily installed by any good mechanical workshop.

Alternatively, you could purchase a B3 1.3L engine and have it fitted. However, you will then have to fit a Unichip and have it specially mapped (calibrated) because your 1.3L ECU will not work properly.

1.3 Ford Ka / Ford Bantam ST90 Performance Kit • SWR - Steve Wyndham Racing

FAQs: Performance Mods Ford Rocam - Steve Wyndham Racing
0helpful
1answer

Where is the wiper relay switch on a Ford bantam 2010 model? fuse is fine but wiper stuck half way across screen.

If it's the front wiper check for voltage to wiper motor, most of the time it is the motor and I don't know of a relay.
1helpful
1answer

How do i check the fuses, and where are they, on a ford bantum xli 1300 2010?

there is a set in the hood and another in ur driver cabin
0helpful
1answer

Ford fiesta 2010 front wiper doesnt work but I hear a sound

Try checking the nut that holds the wiper arm to the spindle they do sometimes come loose.
0helpful
2answers

2010 Reg Ford Focus 5 door hatch rear screen wash not working. Front is OK. How do I fix it?

the washer fluid could be empty / the fuse for the wiper blew / the relay went bad /if you tried to use the wipers without clearing ice away you blew the fuse/ if you just put water in instead of washer fluid it's frozen/ if the wiper works and there is windshield fluid in the tank and not water and all fuses are good the pump motor for the fluid went and is easy to change
0helpful
1answer

Rear wiper not working on 2010 ford escape. how do i fix it?

Mine is neither working. the motor has gone. you have to replace it.
0helpful
2answers

Where do i get clutch master cylinder in my ford bantum

Try a used auto parts place. Try Denton Auto Salvage at 785-437-2223
0helpful
2answers

Wiper not working ford galaxy m2

No solution sorry - mine have done exactly the same - will wipe front screen if you mess with the stalk - rear wiper works when you push the stalk forwards or backwards but no washer to either - have you found a solution? Kind regards - Andy
0helpful
1answer

Ford Taurus 1996-wind screen water squirter not working

You will need a test light/probe to check wether you have power to the windscreen washer bottle motor.If you have power at the motor and it doesnt pump you will need to replace it.Because the wipers are still working its unlikely to be a power supply issue.Can you hear the motor trying to pump when you activate it?If you can hear motor humming then you may have blocked nozzles.Usualy a small sewing needle poked down the squirter nozzles will clear them.Also make sure your water squirter hoses are not blocked and havnt fallen off.
Not finding what you are looking for?

968 views

Ask a Question

Usually answered in minutes!

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

xxxxxx xxx

Level 3 Expert

5117 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...