Question about Cars & Trucks

1 Answer

I need to change the CHECK ENGINE light bulb Pont. Aztek how to access?

I would like some info on removing dash

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 633 Answers

You have to remove the trim around the cluster. Once removed you can unbolt the cluster pull it forward and replace the bulb.

Posted on Oct 26, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 136 Answers

SOURCE: CHECK ENGINE BULB REPLACEMENT

You have to take all the facia off the dash - and then pull the dash cluster out. It is a long hard job for a light bulb. When you take the dash out don't forget to undo the speedometer wire and then the wire plugs on the left and right upper sides of the dash unit.

Posted on Oct 13, 2008

  • 651 Answers

SOURCE: Light bulb went out that lights up the mileage indicator located in the center of the dash under the radio.

check fuses first.

Posted on Apr 14, 2009

  • 2 Answers

SOURCE: Can't remove dash from 1990 toyota celica to replace dash bulbs

hi i had d same problem with my gt4,i lightly wedged a piece of hard plastic between any gap n popped open the clips,be careful tho

Posted on Jul 22, 2009

  • 10 Answers

SOURCE: I have a 2004 Pont. Aztek. The AWD Disabled light is on

AWD Light is caused by your Rear Wheel Hub(s) one or both are going bad. Dealer cost is $500.00 part at Auto Zone is $129.00. Not to difficult to replace if you are some what mechaniclly knowledgable

Posted on Aug 08, 2009

  • 1 Answer

SOURCE: how do i change mazda 6 headlight bulb

This is difficult give yourself a good 30 mins. I have only found one way. Bonnet up - You will need a slim torch and a stubby x headed strewdriver to remove the plastic screws that hold on the wheel arch cover. Turn wheel away to give you more room. Once this is out of the way you can see the back of the light cluster, A twist and the back cover comes off. Remove the electrical connector, locate the retaining clip (much of this is by feel) when you take out the bulb make sure you note the way it came out as the replacement must go in the same way. Do not touch the bulb glass with your fingers, use paper or gloves. By feel, re-fasten the clip then reconnect the electrics. Reposition cover and twist back on, Refasten wheel arch cover. Make sure the cover goes inside the lip of the wheel arch otherwise spray from the wheel may get in., good luck

Posted on Dec 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Is there a way to brighten the the area where the mileage is shown


Instrument lights that have old-fashioned bulbs to provide the illumination can and do become tired, the filaments break or the bulbs become blackened and the light goes out or grows increasingly dim.

The instrument illumination used to be something that could be replaced quite easily by simply reaching behind the dash and removing the light. Those days are far-off and mostly the instrument panel must be removed to provide access which isn't often a very easy task so once the panel is removed it is a good idea to replace all the bulbs. The last one I did needed 14 bulbs.

Manufacturers often used bulb and bulbholder assemblies but I have found ordinary bulbs can be fitted with some fiddling around...

Feb 25, 2015 | 2003 Pontiac Aztek

6 Answers

My check engene light bulb is out, and i need to replace ot before my inspection... Need to know where the bulb is loacted to replace?


The check engine light is located in the message center right above the instrument cluster. To remove it you will need to jest remove the a pillar trim. Those are the plastic pieces that run from the ceiling down to the dash on both sides. Then you will need to remove the upper dash pannel. It is held in by clips. Gently pry up and it will start to release the clips. Once the upper dash panel is out you will see the screws that hold the message center in place. Remove the screws, remove the message center, and replace the bulbs. Hope that helps. Let me know if you have any questions.

Oct 07, 2011 | 1999 Plymouth Grand Voyager

2 Answers

Check engine light, not registering temp


Hi, You'll need to get the trouble codes read. I'm guessing the code probably has something to do with your engine coolant temperature sensor or the engine coolant temperature sending unit.

More info @ http://www.check-engine-light.com/my-cars-check-engine-light-is-on-what-do-i-do.php

Feb 09, 2010 | 2001 Pontiac Aztek

1 Answer

I have a 2003 pontiac aztek. my lights on my instrument panel are burnt out. How do I fix that? Thanks


You can remove panel screws, remove and pull back dash panel, then you will find a couple more screws that holds on instrument panel Remove these screws, pull back panel and you can see the bulbs. They turn and pull out.

Aug 17, 2009 | 2003 Pontiac Aztek

1 Answer

Park lamps don't work


did you check both the fuses under the dash and the ones under the hood?

Aug 14, 2009 | 2001 Pontiac Aztek

1 Answer

How to replace the a dash light on an Pont. Aztec 2001 or what fuses to check (I've check a few and they all seem fine) so I thnk its the bulb.


remove bezel around dash.remove dashboard carefully may haft to unplug wires behind dash to be able to get to bulbs then replace all lites because when one goes bad they usually al go so while you are there replace all of them!!! :)

Jul 02, 2009 | 2001 Pontiac Aztek

5 Answers

I have a 2004 Pont. Aztek. The AWD Disabled light is on


AWD Light is caused by your Rear Wheel Hub(s) one or both are going bad. Dealer cost is $500.00 part at Auto Zone is $129.00. Not to difficult to replace if you are some what mechaniclly knowledgable

May 03, 2009 | 2004 Pontiac Aztek

1 Answer

Replacing dash lights


You may be able to reach the bulbs from the back of the instrument panel, you will need to remove any lower panels that block access, if they can't be removed from the back then you will have to R&R the instrument cluster assy and any other unit that has defective bulbs, make sure you get the correct repacement bulbs, they may look the same but have diffwerent luminosity ratings, wrong bulb will be to dim or to bright and hot burning, this can damage the bulb socket, check your owners manual for more info.

Aug 04, 2008 | 1997 Audi A4

2 Answers

CHECK ENGINE BULB REPLACEMENT


You have to take all the facia off the dash - and then pull the dash cluster out. It is a long hard job for a light bulb. When you take the dash out don't forget to undo the speedometer wire and then the wire plugs on the left and right upper sides of the dash unit.

Jul 17, 2008 | 1997 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...