Question about 1995 Buick Regal

2 Answers

1997 buick windshield washers

The windshield washer pump is not getting power with the switch turned on. I'm looking for the switch wiring diagrams and windshield wiper. washer control module

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 99' Buick Park Avenue, where is the pump and/or fuse for this? Thank you.

Posted on Feb 02, 2015

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Buick Master
  • 2,620 Answers

The wiper module is mounted on the firewall.

Posted on Oct 25, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 96 Answers

SOURCE: I have a 1997 Buick Lesabre limited and the

Your wiper linkage has come apart or broke, you will have to take shroud on top of wipers and take alook

Posted on Sep 17, 2009

  • 7 Answers

SOURCE: how do you access the windshield washer pump on

The washer pump is located on the bottom of the wash fluid bootle. you can access it by removing the front passanger fender liner..

Posted on Jan 12, 2010

  • 182 Answers

SOURCE: Windshield wipers stay on delay all the time.

A wire is shorted out or part of the switch is bad.

Posted on Aug 28, 2008

  • 48 Answers

SOURCE: 2001 Buick Regal LS windshield washer fluid does not spray

There are a number of different issues that could cause this.

-The circuit for the wiper should be the same as the washer; same fuse. -I'd suggest trying to run the washer while the hood is open and the engine off. If it runs, you should hear a dull whine.(a 2nd person might be of use to help look and listen)...(find the pump by following the hoses from the wipers to a unit mounted close to the dashboard in the engine compartment)
-If it runs, check to see if any fluid is coming from a hose that might have become disconnected.
-If the pump runs, and if you see no fluid coming from anywhere, and if you can reach the hose connected to the washer pump, pull that hose off the pump. Try running the pump again to see if anything comes out in a good stream.
-If the pump doesn't run at all, check to make sure the connector hasn't come loose.
-If the pump still doesn't run, check to see if you have 12 volts at the connector at the pump. A simple check can be done with an auto bulb connected to the plug at the motor while the pump switch is pushed.
-If you have power at that point, you likely need to replace the pump and motor.(depending upon the age of vehicle & your mechanical abilities...a call to a local wrecking yard is suggested ..atleast to compare the cost vs. new)

hope that helps

Posted on Oct 08, 2008

  • 819 Answers

SOURCE: where is the windshield washer pump

in the bottom of the washer fluid container. its is held in by friction with a rubber grommet. if you are replacing, get the original pump from the dealer if available. if you buy a universal, they usually leak and the original connector will have to be modified.

Posted on Dec 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

1 Answer

Windshield wiper washer pump fuse


On a lot of cars, that washer pump circuit is really a sub-circuit of the windshield wipers themselves. The wiper fuse is also the washer pump fuse, in other words.

Use a test light or a voltmeter. Pull off the electrical connector at the pump on the washer fluid tank. Have a helper turn the key on, then press for the washer pump to operate. Take your test light and clip the ground lead to the negative battery post. Touch the tester probe to the positive terminal to assure the light is bright, that the test light will work. Now probe the connector at the washer pump. One of them wires should light up the test light, or would show battery voltage with a voltmeter or multi-meter. If it has power when key is on and washer switch on, the motor is bad, or sometimes you have to go a little further and find a ground fault.

If there is no power on any wire at the pump connector, you will have to look at a wiring diagram to diagnose it. Find out just how the pump gets power.

Jan 08, 2015 | Cars & Trucks

1 Answer

How do I change the windshield washer pump on 2002 kia optima


Windshield washer pumps are attached to the windshield washer fluid container. Remove that container and look for the washer pump. That is the only item with two wires connected to it. First remove hose connected to the washer pump and turn the washer switch on. IF water flows from the washer, your water lines are clogged, if no water flows, your washer pump maybe dead or there is no power going to the washer pump.

Try testing IF current is passing/present at the two wires by connecting as continuity tester or simply a small lamp. Switch the washer on and see if the bulb gets lit, if it does, there is power and your problem is the washer pump itself. Replace the pump.

Oct 04, 2014 | 2002 Kia Optima

1 Answer

2009 nissan frontier windshield washer pump won't work


Check fuse in fuse box inside vehicle,if good,then go to windshield washer pump and disconnect wiring,get meter and check if power is going to pump,if so then pump is at fault,if no power,thenwiring could be short somewhere to fuse box.Also check your washer hoses,that they are not kinked or came loose.Pump could just be loose.

Jan 04, 2013 | 2009 Nissan Frontier

1 Answer

Where is the fuse for the front windshield washer motor


If you are just talking about the windshield washer pump/motor that squirts water on the front windshield, there is no separate fuse for that pump. If you are talking about the front windshield wipers themselves then the fuse for that (including the washer pump) is located is the fuse panel inside the vehicle down below and to the left of the steering wheel. Below is a diagram of the fuse layout (first picture) and I marked the 10 amp fuse for the system. As I said if you are talking about the pump/squirter motor there is no separate fuse. Inside the wiper motor itself (located basically on the firewall on the drivers side) is an internal microprocessor as well as an internal relay for that pump. If the processor or the relay is bad, both are internal and the whole wiper motor assy. has to be replaced. It's one complete unit. There is a chance that the pump motor itself could be bad. In the second picture is a breakdown of the washer fluid reservoir. In order to get access at it which is where the washer pump motors are located the right front wheel and splash guard have to be removed. I have marked the 2 washer pump motors which are mounted on the reservoir. I cannot tell you which motor is which but the one for the front has 2 wires at the connector (a black & white wire and a black wire) The rear pump motor has a violet & light green wire and a black wire at its connector. That's how you can tell which one is which. You can test the motor by either pulling it out and applying direct power and ground to it to see if it engauges or while someone is engauging the washer inside the vehicle while you are down there, see if you are geting power at the black and white wire. Check that wire while it is disconnected and using a good separate ground. If you are getting power make sure the black wire is geting a good ground. If all is good (ground & power) than more than likely the pump motor is bad. If you have a power supply problem at the black & white wire than you are looking at most likely a bad wiper motor assy but check for an open power wire from the wiper motor to the pump motor. It's not quite as simple as it used to be. The wiper motor on your vehicle has like a mini computer in it. I'm gonna say the washer pump motor is bad which is the most common. Hope I was able to help and that I didn't get too technical on you but things are not like the old days with separate motors (wiper and washer).

5_20_2012_11_03_19_am.jpg5_20_2012_11_03_40_am.jpg

May 19, 2012 | 2004 Mercury Montery

2 Answers

My windshield washer pump isn't working on my 2006 Dodge Durango. I want to know which fuse to check for my windshield washer pump.


More than likely it's the pump itself. I say this because in a nutshell your pump is computer controled. It receives power through the CAN system on your vehicle. If it were just a fuse MANY other things would not be working. I would see if you are geting power and ground to the pump. If you are then replace the pump. If you are not you may be looking at the switch or a wiring problem or in the system itself. Wish I could give you just a fuse but it's not that simple on your vehicle. I gave you a descrition of how it works but it can be a little confusing.

12_10_2011_11_09_06_pm.jpg

Dec 10, 2011 | Cars & Trucks

1 Answer

1996 buick windshield washer will not turn on. Plenty of fluid, hoses ok, port (squirter) to windshield is not plugged. Pump is not trying to push any liquid. No blown fuses.Wipers work fine. Everything...


Have someone press or hold the washer switch and listen underhood for a small pump sound {Hum}. If you don't hear a small hum you probably need a new washer fluid pump, pretty common for this old of a car. Imagine for the last 15 years sitting in wet fluid,sometimes drying out, getting refilled, turned on and off, on and off that little pump had it's day and retired! Most auto parts stores sell inexpensive replacements. Easily come out and go back in in reverse order. Pumps are usually mounted underside of fluid tank,just follow any visible washer hose.

Sep 20, 2011 | 1996 Buick Century

1 Answer

Replaced windshield washer pump, lines are clear, but won't work.


check fuses and/or wiring harness attached to pump. Use a continuity light (10-15 dollars at any auto store) and check to see the pump is getting electricity by having a friend turning on the washer pump and placing the continuity light probe on the electrical connector to the pump and the fues. if you have no light come on when you place the continuity light to the wiring harness then its a ground wire or the fuse.

Oct 04, 2010 | 1997 Buick LeSabre

3 Answers

Windshield washer Pump doesn't run, but the pump checks out good


there is another small relay box just below the windshield washer reservoir about 11/2" wide x about 4" long the washer pump relay is in there



Nov 23, 2008 | 1999 Ford Explorer

Not finding what you are looking for?
1995 Buick Regal Logo

503 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...