Question about 2005 Ford F-150

1 Answer

Replaced defective battery, now horn sounds when ignition is turned to the on position and will not crank over. Tried to deactivate the alarm with remote with no success

Posted by on

  • 3 more comments 
  • sgfd Oct 24, 2012

    Is there a security light on your dashboard blinking? Also does it attempt to turn over or do you not hear any cranking sounds at all?

  • asr2267
    asr2267 Oct 24, 2012

    horn sounds continueously when key is turned to on position and when turned to start position the same persists and does not crank over.

  • asr2267
    asr2267 Oct 24, 2012

    there is an under dash stock alarm light that blinks countinuously

  • asr2267
    asr2267 Oct 24, 2012

    when remote alarm key unit is used, it will lock the doors but will not unlock them.

  • asr2267
    asr2267 Oct 24, 2012

    any suggestions?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 59 Answers

There could have been a problem with your security system when you changed the battery out. Call your local Ford dealer to see what you can work out. You may need them to reset your security system with one of their factory tools. I'm not sure how you will get it to them to do so, but it does sound like a problem with your security system which typically isn't fixable on your own or even at a non-dealer garage.

Posted on Oct 24, 2012

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

carconet
  • 38 Answers

SOURCE: key stuck in ignition

your ignition have to be replaced focus 2002/7 have that problem and a lot more often if you have a lot of other keys with it,try some wd40 ,but if you do take the key out replace the ignition or you going to get stuck.

Posted on Aug 03, 2010

  • 1584 Answers

SOURCE: turn key on and now no dash lites as usual but a

The vehicle alarm system needs a reset......can be done by most mobile alarm companies or it will have to go to the ford dealer.

Posted on Oct 20, 2010

  • 5 Answers

SOURCE: My 2006 Ford Mustang's factory alarm goes off when

well im a mechanic for village auto clinic in Hempstead,Ny anyway locate your fuse box under the hood and look for the fuse for the alarm check the owners manual if not disconect the alarm start let battery charge but note dont touch radio or anything just let run for 15 to 20 min then drive to nearst mechanic so they could do further inspection to figure out why this is happning for now respond and let me now how thingsturn out...

Posted on Dec 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I disarm the alarm system on my 1998 volkswagen?It wont start ,cranks but wont run..I changed the plugs still wont start,someone said could be in the alarm system to disarm it.


The alarm would cause the car not to crank, and the alarm horn would sound. You can try unlocking the car from the trunk lock to disarm the alarm. But crank and no start could be a bad ignition switch. Do the dashboard lights stay on or go out while the key is in the crank position? They should remain "on". Worn ignition switch could cause the car to crank but not start.

May 04, 2017 | Volkswagen Cars & Trucks

1 Answer

VW golf battery replacement - horn/alarm going off when reconnecting.


I suggest you try inserting the ignition key and turning the key to the fully on position before connecting the new battery. Ensure the door is left open.

If the alarm still sounds then starting the engine or attempting to start it might cancel the alarm.
Reading the vehicle handbook could provide more information.

Jan 21, 2017 | Volkswagen Golf Cars & Trucks

2 Answers

Turn on ignition turn key to start position and engine is not cranking over


run the fault codes to check cam/crank position sensor. Check that the cam shaft is turning (broken timing belt /chain) check immobiliser operation

Aug 16, 2014 | 2005 Dodge Neon

1 Answer

I can't turn off the security alarm on my 1998 nissan pathfinder


I couldn't turn off the security alarm on my 1999 Pathfinder as I replaced the battery,
Solution: I read the solution here to disconnect the positive cable, open the driver's door, insert the key, then reconnected the positive cable, while honking, I turn the key to the left, to the right and to the left again while the door is still open. The honking stopped. Then I started the truck without a problem. Thank you for the hint.

Jun 12, 2012 | 1998 Nissan Pathfinder

1 Answer

My remote is not working and I cannot start my car. The alarm comes on


The active and deactive is in the door switch.Use the passenger side and see if that make a difference.Othere than that roll down a window disconnect the battery put terminal together for 1 minute.leave key in the ignition. Connect battery positive first the negative. reach in the window turn ignition to ACC position (do not crank it). Throughout this period the driver door should be open get in it crank the engine for start.

Apr 01, 2012 | 2000 Jeep Cherokee

1 Answer

I replaced battery in my audi 80 2.0 tdi but have lost the remote and alarm wont stop going off .


Depress lock or unlock button. Manually lock and unlock driver's door within 30 seconds. System should now lock or unlock vehicle. If not, carry out programming procedure.
Programming
When
Key added or replaced. System malfunction: Alarm LED in rear fog lamp switch illuminates for 30 seconds when vehicle is locked.
How
NOTE: A maximum of 4 keys can be programmed (one at a time).
As memory positions of existing keys are unlikely to be known: Obtain and reprogram all keys.
NOTE: Existing key memory positions will be overwritten.
Switch ignition ON. Use key not fitted with remote control. Manually lock vehicle using key. Using first key, press unlock button once (programs memory position 1). Alarm horn sounds once to indicate signal received. Wait 6 seconds. Press unlock button once to confirm programming. Vehicle unlocks. Programming mode deactivated. Switch ignition OFF. To program remaining keys into memory positions 2, 3 and 4. Carry out the complete procedure below for each key: Switch ignition ON. Use key not fitted with remote control. Manually lock vehicle using key. Press unlock button at 1 second intervals, as follows: Twice for memory position 2 (second key). Three times for memory position 3 (third key). Four times for memory position 4 (fourth key). Alarm horn sounds once every time unlock button is pressed, to indicate signal received. Wait 6 seconds. Press unlock button once to confirm programming. Vehicle unlocks. Programming mode deactivated. Switch ignition OFF.
NOTE: Ignition MUST be switched OFF between each key programming procedure

Jan 10, 2010 | 1992 Audi 80

1 Answer

2000 eclipse gs no horn on alarm and locking


Have you tried resetting the alarm, or even disconnecting the car battery and reconnecting it... also make sure all doors and trunk lid is closed

Aug 04, 2009 | 2001 Mitsubishi Eclipse

2 Answers

This is a 1997 Volkswagon Jetta GLS. will not crank since jumpoff


You blew a fuse. Try this site and search for "fuses panel diagram"

vwvortex.com

Jul 06, 2009 | 1997 Volkswagen Jetta

2 Answers

98 celica battery went dead replaced now it want crank


Try this: Unhook the battery. Reconnect the battery. When the horn starts to beep, cycle the ignition key in the ignition on-off 5 times. This resets the alarm; the cycling of the key. Please advise me if this works for you.

Oct 07, 2008 | 1998 Toyota Celica

1 Answer

1997 venture keyless remote programming


SYSTEM OPERATION

System warning lamp located on top of the instrument panel
Press UNLOCK button once , turns on interior lamps and deactivates alarm (if fitted)
Press UNLOCK button twice w/in 5 seconds unlocks all doors, turns on interior lamp and deactivates alarm (if fitted)
To activate alarm system (if fitted):
Switch ignition OFF
Open driver's door
Press Lock button on remote
Close Driver door
warning lamp will flash when system is activated
Press remote power sliding door button will open sliding door (if fitted) only if unlocked first
Pressing remote panic button:
*Sounds horn intermittently
*Flashes exterior lamps
*Turns on interior lamps
**Pressing panic for the second time OR switching ignition ON deactivates alarm.


PROGRAMMING
Remobe key from ignition switch
Remove the "BCM PRGRM" fuse, from the fuse box
Close all doors
Turn ignition switch to the ACC position
With in 1 SECOND , turn the ignition switch to OFF then back to 'ACC'
(really, with in one second)
Open and close the driver's door. A chime will sound, indicating programming mode activated
Press and HOLD LOCK and UNLOCK SIMULTANEOUSLY untill a chime sounds 2 times ( about 15 seconds)
Repeat this exact procedure for all remotes to be programmed
Remove key from ignition
Refit 'BCM PRGRM' fuse.

4 REMOTES MAXIMUM CAN BE PROGRAMMED

Aug 24, 2008 | 2000 Chevrolet Venture

Not finding what you are looking for?
2005 Ford F-150 Logo

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...