Question about Cars & Trucks

Open Question

Massey ferguson TEF 20 circa 1954 diesel knock

AFTER FIRE UP RUNS FOR ABOUT TEN MINUETS THEN WE HAVE KNOCK , IS NOT BIG END DEFINITELY FUEL KNOCK . WHERE NEXT ?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: massey ferguson 3655

sounds like the seals are gone on the 4wd shaft, it takes oil pressure to keep the 4wd off, but if the seals are worn the all passes through and the 4wd will not dissingage, you will need a experianced michanic

Posted on Apr 07, 2009

Ad
VWdan
  • 114 Answers

SOURCE: volvo front end knock

Most likely the sway bar links,if quiet unless you hit little bumps or cracks thats the most likely thing on a volvo. Followed by ball joints and tie rods. If it only happens when you are sitting still and move the steering wheel side to side that would be a tie rod.

Posted on Apr 24, 2009

  • 1 Answer

SOURCE: loud diesel knock nissan terrano II head just replaced.

some black smoke comes out when i put foot down and loses power when goiong uphill i have a nissan mistral/terrano 2.7td

Posted on Aug 20, 2009

  • 58 Answers

SOURCE: 2003 Tahoe, 5.3 liter vortec flex fuel. Engine

this is a comon problem on chevy 00-06 models a computer ground ,it seems ok at sight but inside it's just holding a few wires ,get under the car on the driver side passenger there you should find a two ground wire goin to the block a big, and a small ,the small one gets coroded try to fix it and let me know how it goes ok.

Posted on Feb 25, 2010

exteriorspec
  • 4 Answers

SOURCE: knocking/thumping noise in rear end while breaking

I HAVE THE SAME PROBLEM I'VE BEEN DOING A LOT OF RESEARCH ON IT AND I THINK ITS GONNA BE THE BUSHINGS IN THE REAR KNUCKLE ASSEMBLY AND YOUR HAVE TO CHANGE THE WHOLE ASSEMBLY. I HAVEN'T TRIED IT YET BUT IF YOU CHECK BACK IN A COUPLE DAYS I WILL LET YOU KNOW

Posted on Jan 06, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I got an infinity 2005 g 35. I'm starting to hear a knocking noise. I don't know if its the engine, It sounds like it's coming from the side somewhere but definitely under the Hood.? Idk


if the knock speeds up with rpm increase then it definitely is the engine. if it is a solid sounding knock that would be bottom end. if it is more of a hollow knock or more like a tick then could be top end...lifters, exhaust leak or check to see if anything is hitting your cooling fan.

Feb 28, 2017 | Cars & Trucks

1 Answer

Why is my 2002 Mazda Tribute making a loud knocking noise when I start it


loud knock and for how long

is it a diesel or petrol

broken engine mount

loud tapping is tappets ..should go away once oil reaches top of motor
water pump or bearing something running off drive belts

if high milage engine
a loud knock at engine revolution or half revolution
big end bearings or
piston slap or gudgeon wear

26303613-eolcmrc2k3afiywjhmzpes2a-3-0.gif

26303613-eolcmrc2k3afiywjhmzpes2a-3-1.jpg

Oct 07, 2016 | Mazda Cars & Trucks

1 Answer

Knock comming from engine diesel


if it is a heavy knock that increases with engine rpms , it could be a big end bearing
this can be checked by releasing the fuel line to each injector and if the bearing is faulty the noise will decrease ( remove electric wire if efi controlled )
alternatively it may be a dribbling injector tip and that will be fixed by reconditioned injectors

Nov 07, 2015 | Cars & Trucks

1 Answer

Vanette cargo knocking engine


Petrol or diesel?
Lower bottom end knock or piston top end knock?
Piston pre ignition knock?

Aug 16, 2012 | Nissan Vanette Cars & Trucks

1 Answer

Hi. I have mazda drifter wl turbo 2,5 diesel. Cam belt snapped and broke 2 valves. I replaced the complete head and serviced the pump and replaced new injector nozzles. Also did big ends and small end...


incorrect ignition point for the injectors
diesels ignition point is around 22 degrees btdc for pumps or from the crank sensor if common rail ( information of year or pump or common rail not included )
if it is a pump with pipes to injectors , you have the timing incorrect

Jul 02, 2017 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15360 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...