Question about 1985 Ford Crown Victoria

Open Question

85 ford crown vic ltd. Changed battery and alternator, still won't start, what next?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 335 Answers

SOURCE: Need a fuse panel diagram for 91 Crown Vic.

Try this site
http://www.eautorepair.net/

Posted on Jul 14, 2009

Ad
  • 34 Answers

SOURCE: 1994 crown vic, not PI, is not charging. Put in

there is a alternator fuse on the relay center under the hood that is a large fuse rated i think at like 140 amps check it it probably blew

Posted on Feb 07, 2010

alicantecoli
  • 22219 Answers

SOURCE: 94 ford escort won't start. I have changed the

immobilsor has come on so only course of action is to call a specialist auto locksmith or the dealer to release the immobilisor ,have you lost the chip out of the key?? have a look and try the spare key

Posted on May 25, 2011

jaysonemanme
  • 500 Answers

SOURCE: my 96 crown vic police interceptor, cranks

starting fluid is a thing of the past. dont use it. this car doesnt have a carb, its a throttle body/ electronic fuel injection system. you most likely have a fuel pump or fuel pressure regulator issue. test the fuel pressure, should be anywheres from 35-50 psi

Posted on Oct 11, 2011

coskuarsiray
  • 210 Answers

SOURCE: Why my 2007 crown Vic won't shift in gear

this can be due to out of adjutment of shifter cable which releases the shifter when brake is pressed.

Posted on Nov 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello? Emission problem 1994 crown vic here...


I owned one of these. There is a groove under the butterfly horn of the throttle. There are 8 bolts and a $10 gasket. Often the EGR passage is clogged and it throws off the calibrations and when you clean this groove the engine will run much better.

Jul 21, 2014 | 1994 Ford Crown Victoria

1 Answer

1999 ford crown vic won't start. changed fuel


Maybe your problem is with the one or many injectors, if just one is bad, you will have problems. Get yourself a multimeter and set it to read in ohms and find what spec the injectors should be at. If out of spec, then you need to replace that one injector(s).

Mar 25, 2013 | Cars & Trucks

1 Answer

I drove my 85 ltd crown vic to work fine. After a long day of work she wouldn't crank just turn over. I have changed the distributive module and cap and the rotor button. The timing was reset also


is it getting gass if u got spark to the plug's it should start.dump alittle gas down carb or throttle body making sure to replace air cleaner or snorkle and try and start.if starts could be fuel pump.

Mar 03, 2013 | 1985 Ford Crown Victoria

1 Answer

2004 crown vic battery died. Now I can't open the


the key doesn't work in the door locks?

If that's the case than your only alternative is to call you local towing company or locksmith and have then perform a lockout service.

Feb 25, 2012 | 2004 Ford Crown Victoria

1 Answer

1991 crown vic, new battery, alternator, power going to alternator, still won't charge battery... plz help!!!!!!


check the ground cable. the ground straps to the engine and body alos. Make sure the cables are clean and have no corrosion anyplace.

Mar 17, 2011 | 1991 Ford LTD Crown Victoria

1 Answer

Car won't start


buy a cheap volt meter check voltage on both sides of the starter seleniod on the fenderwell if you have 12 volts on both sides while cranking test voltage at starter if you have 12 volts at starter with fully charged battery and it doesnt start you will need a starter it also sounds like you might need an alternator once you can get it started

Dec 09, 2009 | 1984 Ford Crown Victoria

2 Answers

HOW TO REPAIR 1990 CROWN VICTORIA THAT JERKS WHEN GOING UP A INCLINE. THERE IS A TRANSMISSION FLUID LEAK.


need more info it could be fuel pump as well as the transmission make sure trans. fluid is on the right level

Jul 09, 2009 | 1990 Ford LTD Crown Victoria

1 Answer

1988 Ford Crown Vic Strange Idle (Getting Worse)


i am trying to install an aftermarket temperature guage with capillary tube into my 1988 crown victoria ltd 5.0 efi. where does the capillary tube mount?

Jun 27, 2009 | 1988 Ford Crown Victoria

1 Answer

Engine won't crank after replacing alternator - battery charged


If the start is not grounded it will not turn over the motor check battery cables going to start. There are no reset switches .

Mar 22, 2009 | 1992 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...