Question about 1996 Plymouth Voyager

1 Answer

Blower fan i need to replace the blower fan resistor, not sure where in the dash it goes

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 23 Answers

Blower fan resistors are in the air box on the passenger side below the dash. Basically right at the passengers feet.

Posted on Jan 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How do i fix the blower stuck on high


if it only goes on high, the resistor needs to be changed . It is on firewall ,passenger side of car under wiper assembly behind alternator. not a hard job to do, part is not expensive. you will get low,med , and high back. if not switch on dash panel, or change blower motor, last ,since it is going on- working. good luck

Feb 22, 2015 | 2003 Chrysler Town & Country

3 Answers

How do I change heater fan


It would help to know the make and model. Different manufacturers put them in different places and mount them different.

Feb 19, 2015 | Cars & Trucks

1 Answer

Ac and heater fan is burned out I want to replace it but don't know how to dissemble it 2004 gmc Denali


This is an easy one, in the picture there you will see the resistor, that is the small box with wires to blower, remove that first. also are you sure it is the blower? 90% of the time is the resistor that goes bad, unplug connector from turn the key on until all dash lights come on or start the truck, use a test light and one of the connector wires from the connector you that you unplugged from the blower should have power, the other connector on that plug is the ground and is controlled through the resistor, mark the power wire and then plug back into blower, then use a jumper wire connect one end to a good ground. a paint less area (metal).the other end connect to blower, make sure not to connect to the wire you have power in, and see if blower runs, you may see a small spark when connecting but that is normal. if blower runs replace resistor.

To replace the blower you will unplug connector to blower, remove resistor first just to get it out of the way, some models have an insulator cover over the blower, if so remove the screws and remove the cover next remove the connector, next you will see a tab, hold down tab and turn blower motor counter clock wise to remove from box,blower should drop right out, just make a ref mark on the blower and heater box so when installing new one in goes in correctly, i always note where the plug is and use that as a ref mark, if it is the blower and not the resistor then replace blower with the fan, if you want to just replace the motor and not the fan then remove the nut or clamp which ever one it has and have some one hold fan by its sides and you use a small punch and hammer and tap on stud and allow motor to fall , let me know the out come. good day....

Dec 24, 2012 | Cars & Trucks

1 Answer

2004 Chrysler Pacifica Blower won't work


Usally when a blower motor resistor goes bad the fan still runs on high. The resistor lowers the voltage going to the fan to make it run slower. The high setting usually goes straight thru. Resistors are usually easy to get to, under good on the firewall or under dash passenger side. Cost about $24 at parts store. Replace with new if that doesn't work return it.

Aug 29, 2012 | 2004 Chrysler Pacifica

2 Answers

01 grand.prix ac fan switch only works on high. has a duel temp controller when you turn fan off the only way fan comes back on is to move the temp controller levers


Hi!!
When the Blower Motor Resistor (controls blower speeds) goes bad, the blower motor works only on HIGH SPEED. REPLACE IT.
BLOWER MOTOR RESISTOR Removal & Installation
  • Disconnect negative battery cable.
  • Remove right lower instrument panel insulator panel.
  • Disconnect blower resistor connector located behind right side of dash.
  • Remove blower resistor screws and blower resistor.
To install, reverse removal procedure
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa!!

Feb 18, 2011 | 2001 Pontiac Grand Prix

2 Answers

BLOWER HEATER FAN SWITCH IS ONLY WORKING ON HIGH SPEED WITH LITTLE HEAT.


The blower motor fan is controlled by the blower motor resistor.Its the resistor which controls the fan on respective speed which you select.But if the resistor goes faulty,then it will not be able to set the required speed which you set for fan,so it works on high speed only. In this case you will have to replace the blower motor resistor. Check fog for the location of blower motor resistor location:--- see part number 8 in the diagram below. helpmech_11.gif

The blower motor resistor is located next to blower motor under the dash.Its fitted with 2 screws and a wiring connector.You have to remove the screws and wiring connector and take the resistor out and place the new resistor in same position and connect the connector as well as screws. ------------------- this should help.Thanks.Helpmech.

Jan 18, 2011 | 1999 Oldsmobile Alero

1 Answer

The fan will not come on to blow the heat or anything on my 1997 jeep grand cherokee. PLEASE HELP


Go under the dash on the passengers side.The blower motor and blower motor resistor are located under there.With the switch on just tap the blower slightly and if it goes on then replace the blower motor.If not then follow the wires that go to the resistor and check the resistor.They like to heat up and melt the connectors.So you might have to replace the resistor and the connectors which you can get from the dealership parts department.Make sure you have checked the fuses first.let me know if you have any questions.Good luck.

Dec 08, 2010 | 1997 Jeep Grand Cherokee

3 Answers

My 2000 GMC Yukon 2WD's heater fan now will only work on level 5. First level went awhile ago and every couple months since another one would go. Once level 5 is gone I aint got no heat no mo ! Help !


There is a resistor down below the blower fan on the inside firewall of the passenger side. Advance or Auto-zone carry them and they are not hard to replace or very expensive. You will have to have a small socket though. I am not sure it is a 6 or 8mm.

You will see a long plug about an inch and a half that goes into it. When they burn out you only get high as a default.

Hope this helps.

Nov 03, 2009 | 2000 GMC Yukon

1 Answer

In 2002 Toyota Echo, I need to replace blower motor. There is also a resistor and a ''blower switch'' in a manual, but no explanation of the blower switch. Is this just the 'fan switch' on the dash. ...


blower switch is your fan knob on dash. resistors are located under pass side dash next to blower motor. on alot of cars the blower will work on high speed and not the lower ones- this is a tell tale way to tell the resistor is no good. if this happens again after replacing resistor- ive seen the blower motor shorting out causing the resistor to go bad- then you would have to replace both.(this usually dosnt happen, most often the resistor alone fixes the problem..

Oct 17, 2009 | 2002 Toyota ECHO

2 Answers

A/c fan only works on the highest setting...not the lower ones


A/C fans only really have (2) speeds. (0)Off... and (4)On. Settings 1,2,and 3 are governed by a series of two resistors which in combinations (one, the other...then both) can limit the speed of the fan. When the circuit with these resistors goes bad, the middle speeds of your fan will cease to work. Since the highest setting is unresisted it will never stop working... unless your fan fails.
The solution is economical as these are simple inexpensive parts. For simplicity, the panel with the resistors is typically located in the dash, right behind the speed selector knob. It may be an integral component with the knob assembly depending on your manufacturer. Replace the assembly, or simply the resistors if you are lucky. On the bright note, it doesn't sound like you need to mess with your blower moter... its fine.

Cheers, unclouded.

Jul 07, 2009 | 2002 Chevrolet Tahoe

Not finding what you are looking for?
1996 Plymouth Voyager Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...