Question about 2003 Ford Crown Victoria

1 Answer

No turn signals 2003 crown victoria

Brake lights work,four ways work,headlights work,but no turn signals.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Ford Master
  • 2,620 Answers

Faulty signal switch

Posted on Oct 25, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1632 Answers

SOURCE: 1999 ford crown vic dash light running light problem.

Check all the bulbs at tail end for parking and brakes, test grounds and harness for trailer. Check fuses. clean batery terminals, Re instal head light swich properly and make sure all wires conect.
Vitally

Posted on Sep 09, 2009

Testimonial: "thank you for quick response will try all of your suggestions will re post if no luck."

  • 234 Answers

SOURCE: '96 ford Crown Victoria....No hazard or brake light no turn sigal

Sounds like the multifunction switch. Try working the hazard switch up and down a few times to see if you get some lights to work. If so then replace the switch.

Posted on Nov 09, 2009

  • 180 Answers

SOURCE: ford crown victoria

you must replace the multi fuction switch! also known as the turn signal switch! its common on ford crown vic!

Posted on May 11, 2010

  • 290 Answers

SOURCE: Headlights quit working on my 2001 Ford Crown Victoria Police Int

It needs a new headlight switch assembly. A parts worn out inside. The approx. cost for a new one is abot $160.00. Sorry.

Posted on Dec 26, 2008

djicenova
  • 319 Answers

SOURCE: 1994 crown victoria brake and signal lights don't work

Check fuses under dash. TAL LMP labels

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 ford crown victoria with working brake lights but no parking or rear lights


Duplicate the issue ? You mean the lights are working now ?
The turn signals and brake light circuit is one and the same. The parking lights are on a different circuit. The parking lights get power from the headlight switch and don't travel thru the turn signal switch.
So have you checked the park fuse for power ?
The location of the fuse should be in your owners manual.

Feb 15, 2014 | 2003 Ford Crown Victoria

1 Answer

How do I turn on my headlights in my 2003 crown victoria?


The left (signal) lever twists to turn them on.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 09, 2010 | 2003 Ford Crown Victoria

1 Answer

Headlights go off but signal and tail lights stay on.


The lighting control module is defective and needs to be replaced...A well known defect. I know. I just researched this and replaced mine due to headlight outages. There is extensive information on the web regarding this dangerous defect. The NHTSA conduvcted an investigation and closed it.......No recall on the defective part. You wanna drive your Crown Victoria 2003-2005 at night?..........Pay money and replace the LCM.

Aug 19, 2010 | 2003 Ford Crown Victoria

1 Answer

Replace 2004 Crown Victoria headlight


From the engine compartment, unlock the 3 tabs that are over the headlight housing area. Remove the cover and unscrew the plastic ring that has the wires protruding from it. Carefully pulls the light fixture out of the housing. Pull the 2 L-shaped tabs up and remove the lens section. Reverse the steps to re-install the headlight. If replacing the full turn signal housing, unscrew 2 screws from each light , disconnect bulb wiring and remove. Replace accordingly.

Jul 23, 2010 | 2003 Ford Crown Victoria

1 Answer

Ford crown victoria


you must replace the multi fuction switch! also known as the turn signal switch! its common on ford crown vic!

Mar 06, 2010 | 2001 Ford Crown Victoria

1 Answer

'96 ford Crown Victoria....No hazard or brake light no turn sigal


Sounds like the multifunction switch. Try working the hazard switch up and down a few times to see if you get some lights to work. If so then replace the switch.

Nov 09, 2009 | 1996 Ford Crown Victoria

1 Answer

Tail lights only work with brakes and turn signals fuses fine, blubs new ???


Your headlight switch may be going bad. Work it while someone watches the tail lights. Anything different lights replace the switch.

Oct 15, 2009 | 1988 Ford Crown Victoria

2 Answers

Lights


turn signals and 4 ways or hazards and brake lights all run the same circuit. Parking lights or marker lights you probably have a blown fuse. Depending on what your vehicle is it may have seperate circuit (fuse), check all your fuses

Sep 11, 2009 | 2003 Ford Crown Victoria

1 Answer

Brake and tail light not working, but turn signal is


It could be a faulty brake switch is attached above the brake pedal. You can test it with test light or voltmeter

Sep 11, 2009 | 2003 Ford Crown Victoria

Not finding what you are looking for?
2003 Ford Crown Victoria Logo

318 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...