Question about 1999 Plymouth Breeze

Open Question

Diagram of how to remove a inside door panel of Plymouth Breeze

I would like to replace the motors for the electric windows on the drivers. Both need replacing. So does anyone have a diagram or photos on how to remove the inside door panel to get the job

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: window off track

Looking at the opened door from the inside remove the philips screw near the upper hinge. Pry the speaker grill off with a thin blade putty knife, starting at the bottom left and work to the right. Remove speaker screws and the three screws in the recessed plastic spaces behind. Remove the square covers behind the handle and in the arm rest. Remove the 2 philips screws exposed. Start to pry from the top hinge side between the plastic door panel and the metal door. Work your way around the door until plastic clips release. Once the bottom of the panel and sides are free, lift the panel up and off the door being careful not to pull wiring and door handle mechanism loose. Unplug the as much of the wiring as you can and support the panel so as to not stretch the wiring. Pop the plastic retaining clip on the door handle connecting rod and lift the rod out of the handle. Slowly peel back the vinyl/rubber door cover stuck to the metal door. The window is held in the lower track with two clips that are bolted to the track. Unbolt by raising or lowering the window and using a 10MM socket on the nuts to loosen. Remove the window seal along trhe bottom of the window opening by prying straight up. You can then remove the window and re-epoxy in the lower clips and reassemble window in reverse order.

Posted on Mar 24, 2009

Ad
Dak408
  • 277 Answers

SOURCE: I need to replace the drivers side door mirror.

  1. Disengage clips holding speaker grille to trim panel.
  2. Remove screws holding door trim panel to door from around speaker opening.
  3. Remove screw cap from bottom of arm rest pull cup.
  4. Remove screw holding arm rest pull cup to support bracket behind trim panel.
  5. Remove screw cap from behind inside door latch handle.
  6. Remove screw holding door latch handle to door panel.
  7. Disengage clips holding trim panel to perimeter of door.
  8. Lift trim panel upward to disengage upper retainer channel.
  9. Tilt top of trim panel away from door.
dak408_102.gif

Posted on Dec 05, 2010

  • 36 Answers

SOURCE: How do I replace the

they r usually just held on by snap clips all you have to do is get something behind it and pry it off the clips will pop right out and if they have never been pulled before you might feel like you r going to break it just moove the thing you r prying with a little more twords the point that is being held really tight (were the clip is ) and pry from there they should pop right out, then it just snaps back into place when you r all done

Posted on Apr 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the window motor?


you have to remove the door panel, if the motor is rivetted on remove the entire mechanism , tape the window in the up position, then drill the rivets out and install the new motor, be careful the mechanism is spring loaded and can cause injury!!!!!

Jul 17, 2010 | 1996 Plymouth Grand Voyager

1 Answer

Rear electric window will notwork


Yes . Remove door panel, switch connectors and plastic protective covering on the door. have a helper pull the windw up while you measure the distance from bottom of window regulator to bottom of door panel.
(approx 8-12"), cut a block of wood that will fit between the bottom of the regulator to bottom of door panel wedge it threw the opening in the door a place it between the regulator and door bottom. Wood is soft and sturdy and should hold up until you get the window fixed.
Can the driver control panel switch make that window work. If the answer is No then the problem is the motor on that side. If the answer is yes then the problem is the switch on that window. by the way if the driver control panel gets the window to rise Merry Christmas you don't need the wooden block.

May 05, 2010 | 1997 Plymouth Grand Voyager

2 Answers

I need help with replacing the driver side window in a 2003 ford f-150,four door super crew cab truck.


Removal & Installation
Motor - Front Door
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch
  3. Remove the front door trim panel and watershield.
  4. Tape the window in the full UP position.
  5. Disconnect the window motor electrical connector.
    NOTE Support the window motor while removing the window motor retaining screws.
  6. Remove the window motor bolts and remove the motor.
  7. To install, reverse the removal procedure.
Rear Door
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch.
  3. Remove the rear door trim panel and the rear door trim watershield.
  4. Remove the door speakers.
  5. Tape the window glass in the full UP position.
  6. Disconnect the window regulator electric drive.
  7. Position the connector for the window regulator electric drive inside of the door.
  8. Remove the bolts.
  9. Separate the window regulator electric drive from the rear door window regulator.
  10. Remove the window regulator electric drive from the door.
  11. To install, reverse the removal procedure.

Motor & Regulator

3d4a07e.jpg

Fig. Front Door Trim Panel

7932e42.jpg


Fig. Rear Door Trim Panel-Crew Cab


Regulator - Power Windows

506866e.jpg

Fig. Window regulator arm nuts


db15984.jpg

Fig. Window regulator bolts

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch.
  3. Remove the door trim panel.
  4. Remove the door speaker.
  5. Remove the door watershield.
    NOTE Do not remove the window glass from the door.
  6. Remove the window glass from the window regulator.
  7. Tape the window glass in the full UP position.
  8. Disconnect the window motor electrical connector (power windows only).
  9. Loosen the window regulator arm nuts and pull the arm from the mounting position.
  10. Loosen the bolts and remove the window regulator.
  11. To install, reverse the removal procedure.

Hope helped with this. Good luck.

Nov 16, 2009 | 2003 Ford F150 Regular Cab

1 Answer

Remove drivers side window motor


remove the door trim from the inside of the door, now remove the door plastic weather protector which should expose the window glass and also the electric motor and winder mechanism.
There will be a plastic wire connector inside the door which will have to be disconnected to remove the electric motor etc.
Hope this helps

May 19, 2009 | 1994 Pontiac Grand Am

1 Answer

PASSENGER MIRROR


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Mar 22, 2009 | 1998 Plymouth Breeze

1 Answer

Window off track


Looking at the opened door from the inside remove the philips screw near the upper hinge. Pry the speaker grill off with a thin blade putty knife, starting at the bottom left and work to the right. Remove speaker screws and the three screws in the recessed plastic spaces behind. Remove the square covers behind the handle and in the arm rest. Remove the 2 philips screws exposed. Start to pry from the top hinge side between the plastic door panel and the metal door. Work your way around the door until plastic clips release. Once the bottom of the panel and sides are free, lift the panel up and off the door being careful not to pull wiring and door handle mechanism loose. Unplug the as much of the wiring as you can and support the panel so as to not stretch the wiring. Pop the plastic retaining clip on the door handle connecting rod and lift the rod out of the handle. Slowly peel back the vinyl/rubber door cover stuck to the metal door. The window is held in the lower track with two clips that are bolted to the track. Unbolt by raising or lowering the window and using a 10MM socket on the nuts to loosen. Remove the window seal along trhe bottom of the window opening by prying straight up. You can then remove the window and re-epoxy in the lower clips and reassemble window in reverse order.

Mar 08, 2009 | 1998 Plymouth Breeze

2 Answers

Window on Driver's side of car won't go up.


Hey Kotterpohl.

Sorry i dont have a diagram but what i can tell you is that you can take it to a body shop and they can remove the inside door panel and show you what part snapped or if you are pretty good with tools, screw drivers and star bits, you can take the panel off yourself, they're usually fairly simple to remove. Just be careful of your switches and door handle. Also check the window power motor too.

Hope that gives you a start.

Jan 06, 2009 | 2001 Chevrolet Impala

1 Answer

Driver side window quick working


Remove the arm rest on the door which has screws in it and then unplug the window switch to the window. Then you pull on the door cover....it has plugs on the other side that will snap out and snap back in when putting it back on. You can now look down into the door and see the motor...there will be two or three nuts that need to be removed with a nut driver...one you may have to drill a small hole in the door to get to one of them. Once you've done that you can remove the motor...then the fun begins...replacing the motor is just the opposite of removing it...getting the nuts back on is the hard part because it's on the inside of the door, once you've done that everything is a breeze to put back together.

Jan 05, 2009 | 1999 Chevrolet Lumina

1 Answer

95 blazer, front driver window motor broken need to get window up


When removing the door panel, you need to remove all of the screws first. Then pull the door panel off. There should be screws around the edges or the door panel, and 1-2 screw on the door handle(on the inside). Then pop the door panel off, if the blazer has electric windows and locks you have to disconect them first, if it doesnt have power locks and windows, you have to take the window crank off,there should be a screw in the center of that. Unscrew the door lock and pull up. If it doesnt have them locks then you have to disconect it from inside the door panel

Nov 30, 2008 | 1995 Chevrolet Blazer

Not finding what you are looking for?
1999 Plymouth Breeze Logo

Related Topics:

780 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8759 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...