Question about 1996 Nissan Pathfinder

1 Answer

Replacing water pump on a 1996 nissan pathfinder 3.3L V6

How do I replacewater pump on a 1996 nissan pathfinder 3.3L V6

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 14,384 Answers
Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 16 Answers

SOURCE: 1997 nissan pathfinder timing off.

The cam sprockets should have marks on them (dimples) that should align with marks on the rear timing cover. There should also be a similar dimple on the crankshaft timing sprocket. These will align with their respective marks when the engine is at TDC. The alignment marks are in the following locations as you look at the front of the engine: RH cam sprocket at approximately 11:00, LH cam sprocket at approx 1:00, Crankshaft timing sprocket at approx 4:00 or 5:00. IF you can't find the marks on the cover, put the marks on the sprockets in those approximate positions and set the belt by using a belt tooth count between the marks. Cam to cam should be 40 teeth between the cam marks. Between the LH sprocket and the crank mark should be 43 teeth. You can check TDC by removing your number 1 cylinder spark plug and carefully inserting a long screwdriver and watching the rise/fall as you hand crank the crankshaft into position (which is much easier with the plugs out)

Posted on Aug 21, 2009

kidspeedy
  • 321 Answers

SOURCE: knock sensor 1996 v6 3.3 nissan pathfinder

The Crankshaft Position Sensor is located: Under hood, driver side, front engine area, mounted rear of crankshaft pulley
The Knock Sensor is located: Under hood, center, front engine area, below intake manifold, mounted on block

Posted on Jun 14, 2009

polarcycle
  • 1392 Answers

SOURCE: fuseboxe nissan pathfinder

Here is the best I can do. See if this works. If not, I can try something else.62636615

Posted on Jul 22, 2009

garyq1970
  • 85 Answers

SOURCE: water pump

You should not have to do all that. Let me know if you dont get diagral(sometimes happens)


  1. Drain the cooling system.
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old. 0900c1528018cf80.jpgFig. 1: Water pump assembly-Z24i and KA24E engines 0900c1528018cf81.jpgFig. 2: View of the water pump assembly-VG30E engine
  1. Remove all drive belts.
  2. Unfasten the fan shroud securing bolts and remove the fan shroud assembly.
  3. Unfasten the water pump retaining bolts (note the different size bolts on the VG30i and VG30E engines), then remove the water pump and fan assembly, using care not to damage the radiator with the fan.
If the fan is equipped with a fluid coupling, do not tip the fan/pump assembly on its side, as the fluid will run out.
To install:
  1. Remove all traces of gasket and/or sealant from the pump-to-cover mounting surfaces. Install the water pump and tighten the M6-size mounting bolts to 3-7 ft. lbs. (4-10 Nm). Tighten the M8-size bolts to 7-12 ft. lbs. (10-16 Nm) on Z24i engines, or 12-15 ft. lbs. (16-21 Nm) on KA24E, VG30i and VG30E engines. Always use a new gasket between the pump body and its mounting.
The KA24E engine uses a liquid gasket. Carefully scrape any old gasket material from the mounting surfaces, then apply a 0.079-0.118 in. (2-3mm) continuous bead of liquid gasket around the entire mounting surface.
  1. Install the fan shroud assembly.
  2. Install the drive belt and adjust the tension.
  3. Refill and bleed the cooling system (refer to ), then start the engine and check for coolant leaks.


Feel free to reply with any questions or comments

Posted on Nov 14, 2008

  • 750 Answers

SOURCE: 1999 nissan pathfinders jerks and stalls

try replacing fuel filter

Posted on Jun 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 nissan pathfinder starts but does not rev up 4.0 v6


Either your TPS is not working, MAF Sensor, Fuel PUMP is not giving enough Gas, Blockage in the Air Intake System.

I one had a customer with the very same problem, what we found was a PLASTIC BAG that got sucked into the Air Intake system......

Apr 08, 2013 | 2006 Nissan Pathfinder 4.0.V6

1 Answer

What all years will cylinder heads fit a 1994 pathfinder 3.0 V6?


The salvage yard should be able to give you that information from their interchange manual.

Jul 02, 2012 | 1996 Nissan Pathfinder

1 Answer

1996 Nissan Pathfinder v6 5 speed back up light switch position


The switch that controls the backup lamps on a 1996 Nissan Pathfinder looks completely different and is in a slightly different location depending on whether the vehicle is equipped with a manual or automatic transmission. However, in ether case, the switch is located on the transmission.

On the manual transmission it is called simply, "backup switch".
On the automatic transmission it is part of the "inhibitor switch". (also known as "neutral safety switch")

May 26, 2012 | Nissan Pathfinder Cars & Trucks

1 Answer

1996 pathfinder timing belt


based on the mileage it is about time to change the timing belt. this should be done by a professional or someone with internal engine expertise. it is nothing like changing a fan belt.

Apr 26, 2010 | 1996 Nissan Pathfinder

1 Answer

I need the position of timing marks on 96 pathfinder.


Posted by Asker under a 1995 Nissan Pathfinder for a 1996 Nissan Pathfinder.

For the 1996 Nissan Pathfinder:
Click on the following: direct, free Link:
http://www.2carpros.com/car_repair_information/year/1996/make/nissan/model/pathfinder/1996_nissan_pathfinder_timing_belt_diagram_marks.htm

For the 1995 Nissan Pathfinder:
Click onthe following: direct, free Link:
http://www.2carpros.com/car_repair_information/year/1995/make/nissan/model/pathfinder/1995_nissan_pathfinder_timing_belt_diagram_marks.htm

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Apr 22, 2010 | 1995 Nissan Pathfinder

1 Answer

Remove the upper intake plenum 96 Pathfinder


there are three hoses on the back side that need to be pulled two coolant one vacume. five or six 6mm allen head boltsdown the middle of the intake egr equipped? try to break the large nut loose rather than pull all the egr and dpse sensor apart from the intake.

Mar 21, 2010 | 1996 Nissan Pathfinder

1 Answer

How to realign timing belt on a 1996 nissan


My apologies for the delayed response. I am going back and answering questions that were never answered.
Click on the following Link. It has all the Diagrams for the Timing Belt you will need.
Before Clicking, let me know if this helped.
Again my sincerest apologies...

http://www.2carpros.com/car_repair_information/year/1996/make/nissan/model/pathfinder/1996_nissan_pathfinder_timing_belt_diagram_marks.htm

Jan 17, 2010 | 1996 Nissan Pathfinder

1 Answer

Where is the knock sensor of the nissan pathfinder 1996 V6 3.3 located


in tne valley of the engine in the middle under the intake manifold

Dec 28, 2009 | 1996 Nissan Maxima

Not finding what you are looking for?
1996 Nissan Pathfinder Logo

1,304 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...