Question about 1997 Mercury Sable

1 Answer

How to remove brake starter - 1997 Mercury Sable

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 14,228 Answers

What is a brake starter?

Posted on Oct 24, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the starter located on a v-8 rainier


wcdodkeeuprtaaaaabjru5erkjggg==
where you can found it.
replacing it can be done under hood, by removing brake booster hose and or by under the vehicle. disconnect first cable going to starter. then need to remove the two starter bolts and starter.

Jan 27, 2012 | 2006 Buick Rainier

3 Answers

How to replcae the starter


o remove:Disconnect battery negative lead.Disconnect positive lead and connector of starter relay.
Remove three fixing bolts from starter motor. Top bolt also holds the cable support.Slide starter motor to rear, turn and lift upwards.To reinstall:Transfer locating bush to new starter motor.
Reinstall in reverse order.Torque bolts to 50nm.

Oct 06, 2011 | Cars & Trucks

1 Answer

Starter needsto be replaced


if you are going to change the starter conferm that is the problem begin by removing the negitive cable on the battery pull parking brake raise car if in dought on wire removal reinstalation draw makeshift diagram.bench test starter when removed for confermation of problem.

Aug 21, 2011 | 1991 Mercury Capri

2 Answers

How do you remove a starter from a 95 gmc jimmy


Disconnect the battery first . look on pasenger side of motor close to transmission . you should see it next to the oil pan. on top is a part that looks like a mini starter thats the bendix with a big battery cable and small wires . lable and remove the wires . Should be two bolts 15mm or 9/16 , remove these but be carefull as when the last one is removed the starter will fall . on some models there may also be a small support brace that will be needed to be removed . Check the new starter with the old in shape and size . Also check the teeth count on the starter . It's always wise to change the bendix and the starter as a unit . reassyemblly is backwards of pulling the starter . Hope this helps you.

Jun 06, 2011 | GMC Jimmy Cars & Trucks

1 Answer

How to get to starter on 2003 traikblazer


Removal & Installation 4.2L Engine To Remove:
  1. Disconnect the negative battery cable from the battery.
  2. Disconnect the brake booster hoses from the engine. Starter gm-02-42-1398.gif

  3. Remove the positive battery cable and s-terminal lead from the starter.
  4. Remove the starter from the engine.
To Install:
  1. Install the starter to the engine. Tighten the nut and bolt to 37 ft-lb (50 Nm).
  2. Install the positive battery cable and s-terminal to the starter. Tighten the battery cable nut to 80 in-lb (9 Nm). Tighten the s-terminal nut to 20 in-lb (2.3 Nm).
  3. Connect the vacuum brake booster hose to the engine.
  4. Connect the negative battery cable to the battery.
5.3L & 6.0L Engines To Remove:
  1. Disconnect the negative battery cable from the battery.
  2. Raise and support the vehicle.
  3. Remove the rear steering gear crossmember from the frame. Starter gm-02-53-1399.gif

  4. Detach the wire harness from the transmission oil cooler line bracket.
  5. Detach the transmission oil cooler line bracket from the engine.
  6. Remove the right transmission cover bolt from the transmission cover.
  7. Detach the starter from the engine.
  8. Slide the starter forward and remove the transmission cover.
  9. Remove the heat shield from the starter.
  10. Position the starter so that it can pass between the engine oil pan and transmission oil cooler lines.
  11. Detach the starter lead and battery positive cable from the starter.
  12. Remove the starter from the vehicle.
To Install:
  1. Place the starter between the engine oil pan and transmission oil cooler lines.
  2. Attach the battery positive cable to the starter and starter lead. Torque the battery positive cable nut to 80 in-lb (9 Nm). Torque the starter lead nut to 30 in-lb (3.4 Nm).
  3. Install the heat shield to the starter.
  4. Attach the starter from the engine. Torque the bolts to 37 ft-lb (50 Nm).
  5. Install the right transmission cover bolt into the transmission cover. Torque the bolt to 80 in-lb (9 Nm).
  6. Attach the transmission oil cooler line bracket to the engine. Torque the bolt to 80 in-lb (9 Nm).
  7. Attach the wire harness to the transmission oil cooler line bracket.
  8. Install the rear steering gear crossmember onto the frame.
  9. Lower the vehicle.
  10. Connect the negative battery cable to the battery.
prev.gif next.gif

Aug 19, 2010 | 2003 Chevrolet TrailBlazer

1 Answer

How to remove starter from olds calais 1986


Remove starter by 1) removing battery cables from battery. 2) jack up front of car, put safety jacks under car frame. 3) block back wheel and put on emergency brake. 4) remove the plastic cover next to tranny. 5) remove 2 bolts that hold stater to engine, lower starter, and remove positive cable, and starter solenoid wire (the small one) mark everyhting so you know where they go(take a picture with you phone camera) 6) take starter to a reliable auto parts place where they can test it.

Feb 01, 2010 | 1986 Oldsmobile Calais

1 Answer

Replacing starter


Yes, first disconnect positive battery terminal. remove the three wires from rear-end of starter, remove to two hold down bolts....Reverse for install Be careful quite heavy when laying on your back!! ALSO: if old starter has shims MAKE SURE you use them w/ the new starter or you will damage it! Safety first Chock at least two wheels and set emergency brake!

Oct 14, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Need advice please


Bleed right side first...open valve on caliper and have someone step gently down on brake. close bleeder. repeat till no air comes out. Repeat on drivers side. Keep master cyl full while doing this.
Grinding noise can come from bad starter drive gear, bad flywheel teeth or misaligned starter. You have to check this...I can't see that far!!! Best way to see flywheel teeth is to remove starter and turn engine by hand while looking into starter hole.

May 25, 2009 | 1988 Ford Ranger

2 Answers

Can't find the starter in a dodge spirit 1989


Taken from Haynes repair manual. I used these instructions myself to replace starter motor on my 1989 Dodge Spirit after nearly going berserk at three attempts to remove it without wanting to look it up in book.
1)Detach the negative battery terminal. 2) Working from above the engine, remove upper mounting bolt and nut to starter. (Access is accomplished this way: stand on driver-side fender and look down at brake fluid reservoir. Just below and beyond the brake reservoir you will see a vent hose. Disconnect hose & remove. Now you will see the starter motor from above view. You will be able to see a mounting bolt and a nut connecting starter to engine just above the starter (facing brake reservoir). Remove (1) bolt & (1) nut first, then raise vehicle and suport on jackstands. Then go underneath the vehicle and remove the remaining lower mounting bolt (1) on the starter. Label wires then detach them from starter. Now you can remove the starter. If you find it a tight squeeze, you may want to remove or swing the transaxle on that side for additional access, although that is not mentioned in manual (but I did it). It just gives you more room, but does not seem absolutely necessary. 3) Installation is reverse of removal.
please do rate the solution.
thank you for using fixya.

Feb 09, 2009 | 1989 Dodge Spirit

2 Answers

Noise when cranking up


sounds like dust in the starter moter remove the starter and extend the starter pulling it out with a vice grips and pour4 a small bit of brake fuid on the shaft behind the stater gear(the brake fluid will not atract more dust)

Feb 05, 2009 | 2002 Volkswagen Beetle Turbo S

Not finding what you are looking for?
1997 Mercury Sable Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

fordexpert

Level 3 Expert

5471 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...