Question about 2001 Mercury Sable

1 Answer

2001 sable oil pan

Mechanic said $270 to replace pan that drips oil on exhaust pipe

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 19 Answers

Sounds like he is just going to reseal the pan it is very labor intensive and the price id about right as the exhaust has to be dropped down to access the pan and bolts plus the clean up of the mating services if you get it done demand he install the FELPO OS30717R they fixed the problem with the oem gaskets it cost a little more but well worth the money and no future headaches
johnie G
35yrs ASE Master

Posted on Oct 24, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 95 Mercury Sable oil headache

1999Mercury Sable died...acts like battery dead or alternator, however with key off there is a click, click sound and as soon as you giggle ignition and make sound stop ...there is power but as soon as you turn key on it all goes dead again.. battery takes a charge and don't think its an alternator problem.. think it is a relay switch...possibly the windshield wipers.. have noticed that the wipers turned on for no reason a couple of times and once again when I was messing with this situation

Posted on May 17, 2008

  • 84 Answers

SOURCE: How do you take the oil pan off the engine? Do

You shouldn't have to. Its in the middle of the front of the car. Should have 8 bolts or so holding it on. When you replace that remember a new gasket and to clean the old one off the motor.

Posted on Mar 02, 2009

  • 3640 Answers

SOURCE: There is oil dripping from the air filter intake

change the pcv valve it will probably help.

Posted on Oct 07, 2009

Testimonial: "That was the problem , it was completely clogged,you saved my rear,and a couple of hundred bucks,thank goodness you guys don't work for the goverment "

michigan man
  • 3533 Answers

SOURCE: 2001 mercury sable oil pan

put the car on ramps and remove all of the bolts clean the old gasket off and put a little gasket seal on the bottom of the gasket to hold it in place and put back together and make sure you put the right kind of transmission fluid back in it give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Posted on Oct 15, 2010

Zim1308
  • 543 Answers

SOURCE: to repace the oil pan

yes. it makes slipping the oil pan easier to get around the oil pump.You will also want to purchase new gaskets for the exhaust just to prevent any headaches that may arise from this project.

Posted on May 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do iremove oil pan 01 montecarlo


OIL PAN
Removal & Installation
1. Disconnect negative battery cable. Remove engine torque strut. Raise and support vehicle. Drain
crankcase. Disconnect oil level sensor electrical connector. Remove oil level sensor and oil filter.
Disconnect front exhaust pipe from manifold. Remove right front wheel and splash shield.
2. Disconnect oil cooler pipes. Disconnect A/C compressor electrical connector. Remove A/C compressor,
and position aside. Disconnect engine mounts from frame.
3. Remove flexplate access cover. Use transmission jack at transaxle to raise engine. Remove oil pan bolts
and oil pan. To install, reverse removal procedure. Install oil level sensor after oil pan is installed. Tighten
retaining bolts to specification. See TORQUE SPECIFICATIONS.

Sep 25, 2014 | 2001 Chevrolet Monte Carlo

1 Answer

95 camaro oil leak causing smoke


You need to determine if it is your oil pan, oil sender switch, oil filter, etc. dripping oil onto your exhaust causing the smoke, or if it is coming out of the exhaust itself. If it is dripping onto the exhaust, deal with sealing the affected area. (new oil pan gasket, sender switch, etc.) If coming out of the exhaust, indicated worn piston rings or valve seals.

Jul 30, 2014 | Cars & Trucks

1 Answer

Have a 1999 eclipse 2.0 L...Need to replace oil pan. Do I have to remove any other parts to get the pan off


2.0L Engine
  1. Disconnect the negative battery cable.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Engine undercover Front exhaust pipe Lower oil pan bolts and lower pan Cover Upper oil pan bolt and upper pan Baffle plate

    0996b43f8023193a.jpg Fig. Oil pan and related components-2.0L engine

To install:
  1. Clean all gasket surfaces of the cylinder block and the upper and lower oil pan.
  2. Install or connect the following:
    Baffle plate
  3. Apply a 0.16 in. (4mm) bead of sealant to the gasket surfaces of the upper oil pan.
    Upper oil pan onto the cylinder block within 15 minutes after applying sealant. Tighten the bolts as shown in the accompanying figure.

    0996b43f8023192d.jpg Fig. Upper oil pan bolt location and torque sequence-2.0L engine

  4. Apply 0.16 in. (4mm) bead of sealant to the gasket surfaces of the lower oil pan.
    Lower oil pan and tighten the bolts, in the sequence shown, to 88-106 inch lbs. (10-12 Nm)

    0996b43f8023192e.jpg Fig. Lower oil pan bolt tightening sequence-2.0L engine
    Front exhaust pipe Engine undercover Oil drain plug with a new gasket and tighten to 29 ft. lbs. (40 Nm)

    0996b43f8023192f.jpg Fig. Make sure to the install the new drain plug gasket as shown, or leaks will occur

  5. Lower the vehicle and fill the crankcase to the proper level with clean engine oil.
  6. Connect the negative battery cable. Start the engine and check for leaks.
Non-Turbo Engine
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Drain the engine oil into a suitable container.
  4. Once the oil has completely drained, install the plug and tighten to 25 ft. lbs. (34 Nm).
  5. Remove the front exhaust pipe.
  6. Remove the engine oil dipstick and tube assembly.
  7. Remove the front plate.
  8. Unfasten the oil pan mounting bolts, then remove the oil pan and gasket.

    0996b43f80222121.jpg Fig. Exploded view of the oil pan and related components-1999 2.0L non-turbo engine

To install:
  1. Apply sealant at the point where the engine block meets the oil pump.
  2. Use a new gasket and install the oil pan. Tighten the mounting bolts to 8.9 ft. lbs. (12 Nm).
  3. Install the front plate.
  4. Install the front exhaust pipe.
  5. Install the dipstick and tube assembly.
  6. Safely lower the vehicle to the floor.
  7. Refill the crankcase with oil to the proper level.
  8. nnect the negative battery cable.
  9. Start the engine and check for leaks.

Turbo Engine
  1. Disconnect the negative battery cable.
  2. Safely raise and support the vehicle.
  3. Remove the front exhaust pipe.
  4. Remove the exhaust pipe and muffler assembly.
  5. Drain the engine oil into a suitable container. Once the oil has drained completely, tighten the plug to 29 ft. lbs. (39 Nm).
  6. Remove the dipstick and tube.
  7. For AWD vehicles, remove the transfer case assembly as follows:
    1. With the propeller shaft still installed, remove the transfer mounting bolt.
    2. Insert a suitable prytool in between the transfer case and transaxle, then remove the transfer case from the center shaft.
    3. Remove the transfer case from the center shaft. Do NOT tilt the transfer assembly to the rear or oil will leak out.
    4. After removing the transfer assembly, insert tool MB991193 or equivalent, to prevent the oil from leaking out. Use a piece of wire to suspend the transfer case from the body.

      0996b43f80222122.jpg
      Fig. View of the transfer case with the tool installed to prevent oil from leaking out-1999 2.0L turbo engines
  8. Remove the bell housing cover.
  9. Disconnect the oil return pipe from the oil pan.
  10. Remove the oil pan mounting bolts. Tap the oil pan seal breaker MB998727 or equivalent between the oil pan and the engine block to break the seal and remove the oil pan.

    0996b43f80222123.jpg Fig. Exploded view of the oil pan and sealant application-1999 2.0L Turbo engine

To install:
  1. Clean the sealing surface on the oil pan and engine block. Apply a continuous bead of sealant MD970389 or equivalent to the oil pan.
  2. Clean the oil pan mounting bolt holes in the oil seal case.
  3. Install the oil pan to the engine block. Tighten the mounting bolts to 5.1 ft. lbs. (6.9 Nm).
  4. Use a new gasket and connect the oil return pipe to the oil pan.
  5. Install the bell housing cover.
  6. If equipped with AWD, install the transfer case assembly.
  7. Install the dipstick and tube assembly.
  8. Install the front exhaust pipe.
  9. Install the exhaust pipe and muffler.
  10. Install a new oil filter.
  11. Safely lower the vehicle to the floor and add five quarts of oil to the crankcase.
  12. Connect the negative battery cable.
  13. Start the engine and check for leaks.

Good luck (remember rated this help).

Mar 06, 2010 | 1999 Mitsubishi Eclipse

1 Answer

Oil pan leak


buy a tube of sealer called Right Stuff
1. Remove the flexible exhaust pipe
2. Disconnect the downstream catalyst monitor sendor (OXYGEN SENSOR)
3. Drain engine oil
4. Remove the 15 bolts and the oil pan
5. Clean pan & surface area.
6. Apply sealer 10mm (0.40 inch) diameter of sealer
7. Position oil pan and hand-tighten the oil pan bolts
8. Start with front of oil pan tighten each bolts going around oil pan till all are tighten up.
9. Install exhaust flexible exhaust pipe
10. Connect OXYGEN SENSOR connector
11. Lower the vehicle.
12. Fill oil 5w20 (Spec)

Feb 10, 2010 | 2001 Ford Escape

1 Answer

Do I need to pull my motor in my 2001 Dodge durango to replace the oil pan gasket?


  • Jack up the front of the Dodge Durango, and install a jack stand. Block the rear wheels.
  • Remove the oil plug and let the oil drain into a pan, being sure to remove as much of the old oil as possible.
  • Loosen the bolts holding the oil pan with a socket wrench, and remove the bolts with your fingers. Remove the oil filter, starter motor, cooler lines, oil level sensor, heated oxygen sensor connector and exhaust y-pipe, and then take off the oil pan.
  • Scrape off the old gasket with a thin putty knife, being very careful not to scrape the surface. Be sure all of the old gasket is removed, then wipe the surface with solvent. Spread a bit of oil on the surface to promote adhesion, and apply the new gasket.
  • Replace the oil pan, exhaust y-pipe, heated oxygen sensor connector, oil level sensor, cooler lines and starter motor, and install a new oil filter.
  • Raise the vehicle slightly with the jack and slide out the jack stand before lowering the vehicle and removing the jacks.
  • Fill the engine with the appropriate amount of oil. Check the level with the dipstick to be sure you have the right amount.
Good luck and hope this helps.


Nov 03, 2009 | 2001 Dodge Durango

1 Answer

How do I replace the oil pan gasket on a 2001 GMC Yukon XL?


Changing the oil pan gasket on a GMC Yukon XL is realtively simple, but does require removal of the exhaust pipe. You will need a new oil pan gasket and a new exhaust pipe flange gasket.
Put the car on ramps or jacks to access the undercarriage.
Remove the exhaust pipe by removing the 3 nuts holding the exhaust pipe flange to the exhaust manifold. These nuts often rust and prior application of penetrating oil may be required to remove them without damage. Once the pipe is unbolted, work the exhaust system loose from the hanging brackets. In most cases the entire system does not have to be removed since there is enough room to remove the pan with only the front hangers removed.
Drain the oil from the engine
Remove the 10 mm bolts holding the pan to the block.
Remove the old gasket material and scrape any remaining gasket from the block and pan.
Install the new gasket. Forma-Gasket or a similar product may be used in small quantities to "glue" the new gasket in place and prevent shifting while the pan is reattached to the block.
Reinsall the 10 mm bolts in a cross pattern to ensure the gasket is compressed evenly. Do not overtighten the bolts.
Replace the pipe to flange gasket between the exhaust pipe and the exhaust manifold with a new part.
Reattach the exhuast pipe to the hangers.
Install the 3 bolts connecting the pipe flange to the exhaust manifold.
Fill the engine with oil.

Sep 15, 2009 | 2001 GMC Yukon

1 Answer

How do you take the oil pan off the engine? Do you have to take off the exhaust pipe?


You shouldn't have to. Its in the middle of the front of the car. Should have 8 bolts or so holding it on. When you replace that remember a new gasket and to clean the old one off the motor.

Mar 02, 2009 | 1997 Mercury Sable

2 Answers

05 susuki forenza


Removal Procedure
1. Disconnect the negative battery cable.
2. Drain the engine oil from the engine crankcase.
3. Remove the exhaust flex pipe retaining nuts from
the exhaust manifold.
4. Remove the exhaust flex pipe retaining nuts from
the catalytic converter or the connecting pipe.
5. Remove the exhaust flex pipe.
6. Remove the oil pan flange–to–transaxle retaining
bolts.
7. Remove the oil pan retaining bolts.
8. Remove the oil pan from the engine block.
Cleaning Procedure
1. Clean the oil pan sealing surface.
2. Clean the engine block sealing surface.
3. Clean the oil pan retaining bolts.
4. Clean the oil pan attaching bolt holes in the engine
block.
5. Clean the oil pan scraper.
Installation Procedure
1. Coat the new oil pan gasket with sealant.
Important : Install the oil pan within 5 minutes after applying
the liquid gasket to the oil pan.
2. Install the oil pan to the engine block.
3. Install the oil pan retaining bolts.
Tighten
Tighten the oil pan retaining bolts to 10 NSm (89 lb–in).
4. Install the oil pan flange–to–transaxle retaining
bolts.
Tighten
Tighten the oil pan flange–to–transaxle bolts to 40
NSm (30 lb–ft).
5. Install the exhaust flex pipe.
6. Install the exhaust flex pipe retaining nuts to the
exhaust manifold.
Tighten
Tighten the exhaust flex pipe–to–exhaust manifold
retaining nuts to 35 NSm (26 lb–ft).
7. Install the exhaust flex pipe retaining nuts to the
catalytic converter or the connecting pipe.
Tighten
Tighten the exhaust flex pipe–to–catalytic converter
or connecting pipe retaining nuts to 35 NSm (26 lb–ft).
8. Connect the negative battery cable.
9. Install the oil pan drain plug.
Tighten
Tighten the oil pan drain plug to 35 NSm (26 lb–ft).
10. Refill the engine crankcase with engine oil.

Jun 14, 2008 | 2005 Suzuki Forenza

Not finding what you are looking for?
2001 Mercury Sable Logo

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

fordexpert

Level 3 Expert

5530 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...