Question about 1999 GMC Yukon Denali

1 Answer

What r the torque specifications on installing a head on 2000 sierra 5.3 and the tightening sequence

2000 gmc sierra slt 5.3 liter

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • GMC Master
  • 76,673 Answers

You must use new bolts, failure to do so will result in redoing the job.

Tightening sequences
intakes side 15 13 11 12 14
center 10 3 1 5 9
exhaust side 7 6 2 4 8

Step 1
all 11mm bolts 22 ft lbs
Step 2
all 11mm bolts turn add 90deg
Step 3
11mm bolts 1-8 turn add 90 deg
11mm bolts 9 and 10 turn add 50deg
Step 4
all 8mm bolts 22 ft lbs

Posted on Oct 24, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 124 Answers

SOURCE: where is the 4x4 encoder motor sensor located on my 03 sierra

the encoder motor sensor is inside the encoder motor. the encoder is located at the transfer case. Remove the encoder and by part number 88962315 this is the sensor. you will have to retime the motor after
hope this helps

Posted on May 06, 2009

canbruce75
  • 1776 Answers

SOURCE: how to replace a water pump on a 5.3 liter sierra

I suggest that you visit the autozone.com website and register the vehicle. It doesn't cost anything and will give you access to an online repair manual. The steps for replacing the water pump should be available there. Hope this helped and best wishes.

Posted on Aug 31, 2009

  • 460 Answers

SOURCE: I replaced heater core in 1999 gmc sierra 1500 5.3

no,, the system works from a vacuum and has to be worked on in a service garage. sorry about the bad news...

Posted on Nov 12, 2009

  • 22 Answers

SOURCE: 2003 gmc sierra temp gauge needle stuck in 5 o

Bad IPC.......If u can round up a tech 2 scanner, do a guage sweep and i bet u will see the temp guage will not operate correctly......a new IPC (Instrument Panel Cluster) is really the only fix. Once installed it has to be programmed. If u need any help send me a return message.

Posted on Jan 24, 2010

  • 335 Answers

SOURCE: How do i put a new ac belt on for a 2000 gmc

Hello, this is the instructions for replacing the a/c belt.

  • Remove the accessory drive belt.







  • d7251da.gif
  • Rotate the air conditioning (A/C) drive belt tensioner clockwise in order to relieve the belt tension.
  • Remove the A/C drive belt.59d2902.gif
  • Posted on Jun 15, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


    Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
    1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
    2. Step 2: Bolts 1-10 verify torque without loosening
    3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
    4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
    5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


    26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

    Dec 10, 2015 | Dodge Cars & Trucks

    2 Answers

    Gmc 2003 yukon xl denali 6.0 v8 head cylinder bolts torque


    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
    · Tighten the cylinder head bolts.
    Tighten
    1.Tighten the M11 cylinder head bolts a first pass in sequence to 30 N·m (22 lb ft).
    2.Tighten the M11 cylinder head bolts a second pass in sequence to 90 degrees .
    3.Tighten the M11 cylinder head bolts (1, 2, 3, 4, 5, 6, 7, 8) to 90 degrees and the M11 cylinder head bolts (9 and 10) to 50 degrees a final pass in sequence Tighten the M8 cylinder head bolts (11, 12, 13, 14, 15) to 30 N·m (22 lb ft). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.

    25713066-cke0xeuuw3cel0i3clrurogv-4-0_0.gif

    May 25, 2015 | 2003 GMC Yukon Denali

    2 Answers

    Can't find the torque head bolt pattern for a 1996 gmc sierra 5.7 vortex


    The "pattern" for ANY cylinder head is pretty much the same...start with the bolts in the center of the head and work your way out to both ends.
    Torquing the cylinder head on your 5.7L Vortec engine to manufacturer specifications requires the use of a "torque angle" gauge, as well as a traditional torque meter.

    The torque specifications are as follows:

    > Step 1: All bolts: 22 Ft Lbs (30 Nm.)
    > Step 2: Short bolts: Additional 55 degrees; Medium bolts: Additional 65 degrees; Long bolts: Additional 75 degrees

    May 20, 2012 | GMC Sierra 1500 Cars & Trucks

    2 Answers

    2001 daewoo lanos dual overhead 1.6 liter head bolt torque and sequence


    1. Tighten cylinder head bolts to 25 N.m (18 ft. lbs.). Tighten bolts an additional 70 degrees plus 70 degrees plus 30 degrees using angular torque gauge .
    2001-daewoo-lanos-dual-overhead-1-6-vrq3bch1e30nz1jlq5sn5nnt-4-0.gif

    Oct 20, 2011 | 2000 Daewoo Lanos

    1 Answer

    Correct pressure for torque the head of mazda pickup 1998


    Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


    Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



    B2500 4 Cylinder

    Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







    B3000 3.0 6 Cylinder

    Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









    B4000 4.0 6 Cylinder

    Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


    Good luck with this job!

    Feb 06, 2011 | 1998 Mazda Pickup

    2 Answers

    What r the torque specifications on installing a head on a 1999 yukon and the tightening sequence


    Check this procedure...
    1. Tighten the first design cylinder head bolts as follows:
      1. M11 bolts 1st pass: in sequence to 22 ft. lbs. (30 Nm).
      2. M11 bolts 2nd pass: in sequence + 90 degrees.
      3. M11 bolts (1,2,3,4,5,6,7,8): + 90 degrees.
      4. M11 bolts (9 and 10): + 50 degrees.
      5. M8 cylinder head bolts (11,12,13,14,15) to 22 ft. lbs. (30 Nm). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.
    2. Tighten the second design cylinder head bolts as follows:
      1. M11 bolts (1-10) 1st pass: in sequence to 22 ft. lbs. (30 Nm).
      2. M11 bolts (1-10) 2nd pass: in sequence + 90 degrees.
      3. M11 bolts (1-10): + 70 degrees.
      4. M8 cylinder head bolts (11,12,13,14,15) to 22 ft. lbs. (30 Nm). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.

    c409909.jpg

    Fig. Cylinder head bolt tightening sequence-4.8L, 5.3L and 6.0L engines (click for zoom)


    Install the cylinder head bolts in sequence to 22 ft. lbs. (30 Nm). The bolts must be tightened once, then be tightened again in sequence in the following order:
    1. Step 1: Short length bolt: (3, 4, 7, 8, 11, 12, 15, 16), plus 55 degrees.
    2. Step 2: Medium length bolt: (14, 17), plus 65 degrees.
    3. Step 3: Long length bolts: (1, 2, 5, 6, 9, 10, 13), plus 75 degrees.

    7f05cb7.jpg

    Fig. Cylinder head bolt tightening sequence-5.0L and 5.7L engines

    Aug 04, 2010 | 1999 GMC Yukon Denali

    1 Answer

    What is the right Torque Specification of the cylinder head bolt,main bearing and connecting rod bearing for a 1997 Ford F 150 4.2 liter? Thank you...


    Cylinder heat bolt torque:
    Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
    Main bearing torque:
    Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
    Connecting rod torque:
    Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

    May 17, 2010 | 1997 Ford F150 Regular Cab

    3 Answers

    Need to know the head bolts torch specs on 98 toyota v6


    heres the torque specs and the way to tighten the head bolts for your 1998 toyota sienna, hope this helps,
    12 point bolts step 1- 40 ft lbs
    step 2- additional 90 degrees
    recessed bolt 13 ftlbsaf151d2.gif

    May 12, 2010 | 1998 Toyota Sienna

    1 Answer

    Torque specs for cylinder head on a 200 ford focus with 2.0 ltr single overhead cam. and for connecting rod... Thank you much.


    1. CAUTION: Always install new cylinder head bolts. NOTE: Lubricate the cylinder head bolts with Super Premium 5W 30 SAE X0-5W 30-QSP or equivalent meeting Ford specification WSS-M2C153-G prior to installation. Install the cylinder head assembly and tighten the cylinder head bolts in the following sequence.
    1. Tighten all bolts in a single sequence to 50 Nm
    2. Back the bolts off 1/2 turn.
    3. Tighten the bolts in sequence shown to 50 Nm .
    4. Rotate all the bolts in a single sequence an additional 180 degrees in two steps of 90 degrees each.
    9 3 1 5 7
    8 6 2 4 10 sequence for head


    Spec for rod 38Nm

    May 07, 2010 | 2000 Ford Focus

    1 Answer

    Need cylinder head gasket torque specs.


    looks like there is special sequence to reassemble and tightening, a quick note replace any bolts that have two punch marks.tighten as follows: x x x x x 10 4 2 6 8 x x x x x 7 5 1 3 9 torque all down to 15 ft lbs torque to 30 ft lbs plus 90 degrees. Good luck!

    Sep 18, 2009 | 2000 Ford Focus

    Not finding what you are looking for?
    Cars & Trucks Logo

    219 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts

    yadayada
    yadayada

    Level 3 Expert

    76649 Answers

    Freddy

    Level 3 Expert

    1311 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...