Question about 1993 Toyota 4Runner

1 Answer

What are the torque settings for front rotors to hubs on 1993 hilux surf

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Toyota Master
  • 1,013 Answers

Hi i have found a step by step guide for this havent read all the way through but it may help good luck ivan uk
http://www.hilux4x4.co.za/simon/overhaul_front_axle/index.php

Posted on Oct 24, 2012

  • peter healey Oct 25, 2012

    Thanks Ivan, good article but no mention of the specific torque setting I was looking for however I managed to find it through a friends garage, it was 64nm.

  • ivan whisker
    ivan whisker Oct 25, 2012

    no probs i didnt read it all the way through thought it might of mentioned it but never mind you got it in the end all the best ivan

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 159 Answers

SOURCE: How do I replace the front rotors on my 1993 Toyota Land Cruiser?

have to pull the whole spindle off to get the rotor off..they come off from the back side...real aggravating

Posted on Jun 04, 2009

  • 34 Answers

SOURCE: Cyl. head tightening torque and sequence for a

The online manuals are a super help. I use them all the time. http://www.autozone.com/autozone/myzone/profile/membershipBenefits.jsp

Posted on Oct 14, 2009

  • 1 Answer

SOURCE: How much lb ft. of torque should i put on the

what is the valve clearance and cylinder head torque for toyota 2lt diesel engine

kasim

Posted on Mar 19, 2010

jebild
  • 178 Answers

SOURCE: what is the torque setting for the wheel bearing

there's a manual here: http://myweb.dal.ca/is353832/93fsm/

Posted on Jul 07, 2010

kirkx
  • 2019 Answers

SOURCE: what is the torque setting

Depends on 2wd or 4wd, type of hub, friction, etc.
Here is a description of one:

http://www.hilux4x4.co.za/simon/overhaul_front_axle/front_axle_3.php

Here is another that says to adjust based on rotation drag:

http://www.4x4community.co.za/forum/showthread.php?t=7131

Posted on Jan 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs bearing


Honestly you should search google. It is right there. the inner hub nut must be torqued to 59 Nm rotate the hub three times in each direction and then loosen the inner hub nut until it can be turned by hand, then again tighten the inner hub nut to 25 Nm. the lockwasher against the inner hub nut, it only goes in one way, it has a small inner tab that locates with the key way of the hub, this is between the threads. Once the lock washer is in the correct position, you can now install the outer hub nut, this outer nut must be torqued to 47 Nm, once you have tightened this outer nut, please once again check that the starting effort is correct.

Oct 18, 2013 | 2007 Toyota Hilux 2.5

1 Answer

Procedure for front wheel bearing (hub assembly) replacement


jack up vehicle wheel in question and install jack stand.remove wheel. Unbolt 2 caliper bracket bolts and pry caliper assembly up off brake rotor and hang off to the side with bungee.remove rotor . remove large axle nut. From the back of the hub remove hub bolts most commonly 15mm.Using a slide hammer style wheel puller the hub can be removed. if all you have is a big hammer hit the hub back and forth side to side until it can be removed. Bolt in new hub assembly and torque bolts.Install axle nut and torque. install rotor and caliper. reinstall wheel and torque.

Nov 28, 2010 | 2001 Chrysler Concorde

1 Answer

Left front wheel bearing replacement diagram


Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Lubricate the threads on the halfshaft with clean engine oil.
  3. Remove or disconnect the following:
    • Front wheels
    • Halfshaft hub nut
    • Caliper from the steering knuckle WARNING
      DO NOT allow the brake hose to support the weight of the caliper.
    • Brake rotor
    • Anti-lock Brake System (ABS) sensor from the backing plate
    • Hub and bearing assembly from the backing plate
    • Hub and bearing assembly from the halfshaft
    • Hub and bearing assembly
To Install:
Exploded view of the front hub mounting and related components 7922xg36.gif

  1. Install or connect the following:
    • Hub and bearing assembly onto the halfshaft
    • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
    • ABS sensor
    • Brake rotor
    • Caliper on the steering knuckle.
    • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
    • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Oct 18, 2010 | 2001 Oldsmobile Aurora

1 Answer

Is there any special tools required to change front wheel bearing on 2003 mini


you will need a big socket to remove the axle nut--about 20 mm or so. Other than that, I don't think so. Procedures from autozone.com below. it doesn't mention having to press bearing into hub.


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Front wheels Hub nut Brake caliper Rotor ABS sensor Wheel hub from steering knuckle and driveshaft Wheel bearings
To install:
  1. Install or connect the following:

    Wheel bearing into hub Wheel hub to steering knuckle and driveshaft; torque bolts to 41 ft. lbs. (56 Nm) ABS sensor; torque to 6 ft. lbs. (8 Nm) Brake rotor and caliper New flanged hub nut; torque to 134 ft. lbs. (182 Nm)

Oct 05, 2010 | 2003 Mini Cooper

1 Answer

REMOVAL OF FRONT WHEEL BEARINGS


Front (4 Wheel Drive) To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Tire and wheel assembly
    • Rotor (See: Disc Brake Rotor)
    • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
    • Electrical connection for the wheel speed sensor
    • Front drive halfshaft assembly (See: Halfshaft)
    • Hub and bearing assembly mounting bolts 4WD front hub 9308kg35.gif

    • Hub and bearing assembly
To Install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
  2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
  3. Install or connect the following:
    • Hub and bearing assembly
    • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
    • Front drive halfshaft assembly (See: Halfshaft)
    • Electrical connection for the wheel speed sensor
    • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
    • Rotor (See: Disc Brake Rotor
    • Tire and wheel assembly
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  4. Torque the lug nuts to specification
  5. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Aug 03, 2010 | 2001 Chevrolet Silverado 1500

1 Answer

How i can fix the wheel bearing of my mercury cougar 93.is front one


Buy Chilton or Haynes manual.
Break loose lug nuts. (One turn)
Lift car with jack.
Remove wheel.
Remove brake caliper and hang with something other than the brake line.
Remove brake rotor.
Remove large hub nut. Borrow socket from auto parts store.
Hub should slide off. A 2 jaw puller may be needed if it doesn't slide right off.
You are supposed to discard the hub nut and buy a new one. I always reuse mine...

After installing new hub, torque hub nut at 188-254 ft-lbs. (Which is a lot.)
Reinstall everything in reverse order.
Now is a good time to clean and lube the caliper slide pins and check the condition of the brake pads.
Torque lug nuts 85-105 ft-lbs.

May 19, 2010 | 1993 Mercury Cougar

1 Answer

Left front hub replacement 2WD.


2WD pickups don't have hubs. They have rotors with bearings. Once you have the brake assembly supported, remove nut from spindle. Be sure not to strip the threads on the spindle. Remove the front set of bearings and pull the rotor off. Remove the rear set of bearings. Be sure to pack greases into new bearings prior to installation. Insert new rear bearing into rotor and replace onto spindle. Insert new front bearing and washer and re-install nut. Tighten to recommended torque specs, grease fittings and replace brake assembly.

May 15, 2010 | 2005 Chevrolet Colorado

1 Answer

Torque setting for grand am rotors


The rotors are not bolted to anything, they are sandwhiched between wheel & hub. Therefore there is no specification for them. Caliper bolts are 38lbs if that's what you were looking for.

Apr 09, 2009 | 2003 Pontiac Grand Am

Not finding what you are looking for?
1993 Toyota 4Runner Logo

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...