Question about 1998 Toyota Corolla

1 Answer

How do you take off the inner door panel on 1998 Corolla?

I see four screws: one in door handle, two under arm rest, one snap screw at left side of door. What do I do next?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 152 Answers

Pull on it genlty. it should just snap or pop off. this link should provide more assistance.
http://www.autozone.com/addVehicleId,2378801/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c152801a86b2

Posted on Jan 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Want to replace broken outside door handle on 1993 corolla


  • remove screw on inner door release cover
  • pull latch out-slide and pull
  • remove inner linkage
  • remove window winder or switch
  • remove arm rest (2 screws)
  • undo screws and clips and remove trim
  • wind window up
  • from inside the door remove operating linkages-
  • two 10mm screws hold the outside handle
  • on some cars you might have to undo the latch to make room to undo the two screws for the handle
I know it is brief but it will give you an idea of what needs to be done .hope this helps.
should take 30mins

Sep 14, 2011 | 1993 Toyota Corolla

1 Answer

My inside door latch (driver side) snapped off...what do I need to do to replace?


Remove the inner door panel. The handle will now be accessable, just get one from the dealer and put it on. The door panel is held on with snap inserts around the perimeter of the panel about every 6" or so. There are also some screws in the arm rest and handle. A flat screwdriver slipped under the panel, starting at bottom, will release the snaps.

Sep 02, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Replace outside door handle


you need to remove the inside door panel first. there will be a screw at the inside door handle and two screws for the armrest in the center of the panel. look around the outside edges of the panel for any other screws or clips to remove. the rest of the clips are behind the panel and snap when you pull on the panel. once off with the window up you can see the door handle screws. two of them. remove the connecting rods first.depending on which door you may have a lock rod also. then remove the screws and the handle will come out. good luck

May 22, 2010 | 1998 Toyota Corolla

1 Answer

I have a 1992 Buick LeSabre and cannot open the drivers door from the inside. How do I remove the door panel?


All screws have to be removed and the window switch panel has to be disconnected. It may have hidden screws or simply snaps into place. Pull the inner door handle out and there should be a screw holding the escutcheon plate on the door, The arm rest is also held with at least two screws, remover these. Use a flat tool to pry along the edge of the door and door panel, pop the panel away slightly, the snapping point are the places where the panel is held with nylon panel snaps that screw in to the door panel. If you break these you can buy them at an auto parts store.
The door handle pulls on a rod that pulls on the door latch, this is held in place with a bell crank hook / lock. This is usually the part that fails.....

Feb 13, 2010 | 1992 Buick LeSabre

1 Answer

How do I take off the door panels to replace the interior/exterior locks for the '99 corolla?


start by taking out the screw in the door handle, take the door handle off, (slide it out) next you have to pry off the soft rubbery arm rest cover, there will be two screws under there take them out and the rest of the door panel is held on by rivets, just pop the panel out and lift it up to slide it off, good luck

Dec 03, 2009 | 1998 Toyota Corolla

1 Answer

HOW TO CHANGE EXTERIOR DRIVER DOOR HANDLE


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then pull back the weather seal and disconnect the linkage to the outer handle and remove the bolts holding the handle onto the door

Oct 21, 2009 | 1998 Toyota Corolla

1 Answer

How do you remove the inner door lining of a 98 nissan terrano?


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Oct 21, 2009 | 1998 Nissan Pathfinder

1 Answer

Trying to replace the inside door handle of a 1997 gmc suburban


The door is installed by holding it at a 45 degree angle and lowering the top edge until it meets the window gap. It is snapped down then simply swings into place. Then it is pressed together until the plastic clips sap closed. After that the pieces like door handle, arm rest and speaker and grill cover are installed using screws. This is for both hard plastic and soft door panels. Just reverse this process.
Start by checking the arm rest. There should be several screws that attach it to the steel inner door panel. Depending on the door handle and if equipped, the speaker and cover.
Once your sure all that you have checked for all mounting screws then the next step it to pop the door panel off. The panels are attached using plastic clips that are attached to the panel. These clips will have a male type prong that snaps into a female receptacle on the steel inner door panel. Starting at the bottom place a wedge (like a scraper or wonderbar) between the gap of the panel and inner steel door and pry it apart. The best place to start is at the lower outside corner. Once you have a couple popped apart you can use your hand and pop the rest. Do this at the bottom and work your way across and up because the top lip where the panel and window gap meet are held differently. That section needs to be forced up.
Hope this helps

Sep 13, 2009 | 1999 GMC Suburban

1 Answer

Drivers side door on my jeep cherokee will not open from inside


most likely the inner door handle has a broken hooking tab for the rod to the latch plate.most door panels are held in place with a few screws around the door pull handle and arm rest than most of the sides and bottom of the door panel are held by plastic snap clips. with a large straight blade screw driver start at a corner of the door panel , slide the blade of the screw driver under the edge of the panel and lightly pry out untill you lossen up one of the clips than slide along the screw driver to the next clip , keep going till the panel is lossened up.

Mar 29, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Removal of left front panel, inside, of 2002 dodge caravan


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Feb 18, 2009 | 2002 Dodge Caravan

Not finding what you are looking for?
1998 Toyota Corolla Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...