Question about 2002 Buick Century
Reset security system after removing battery cable
Posted by Anonymous on
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Some are in the inlet to the evaporator and some could be in the condenser line. You can get a new orifice tube on autozone for $5 - 20
Posted on Jul 14, 2008
SOURCE: 95 Buick Century dash removal?
you should not have to remove the dash to install a new radio all you have to do is remove the trim around the radio and then take out the bolts that hold the radio in and remove the wires from the back and also if there is a Walmart or Radio Shack near you get an installation kit and you plug it from the plugs from your old radio and it is alot easier to wire it that way
Posted on Mar 04, 2009
SOURCE: need to reset the key fob
Sit in the driver's seat
Close all vehicle doors; ignition key should NOT be in the ignition, and ignition should be OFF.
Press and hold UNLOCK on your driver's door lock switch, insert and remove your ignition key TWICE, and insert the key in the ignition; this time LEAVE IT. DO NOT TURN THE KEY!!
LET GO OF THE DOOR SWITCH; listen for 3 dings after which, with the key still in the ignition, you will press and hold both LOCK and UNLOCK AT THE SAME TIME on your transmitter for 12 seconds. or until you hear 2 DINGS which indicate a newly programmed transmitter.
If you wish to use more the one transmitter (4 MAX), press and hold lock and unlock just as the first transmitter.
PULLING OUT THE IGNITION KEY ends this procedure :-) !
Posted on May 07, 2009
30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself. Good luck and hope this helps, keep me posted, be glad to help.
Posted on Jul 23, 2009
On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door
Posted on Sep 29, 2009
Tips for a great answer:
Dec 24, 2014 | 2002 Buick Century
Jan 12, 2018 | 2000 Buick Century
Jul 03, 2011 | 2002 Buick Century
Jun 14, 2011 | 2002 Buick Century
May 30, 2011 | 2005 Buick Century
Nov 29, 2010 | 2002 Buick Century
Nov 11, 2009 | 2005 Buick Century
Oct 31, 2017 | 2002 Buick Century
142 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: