Question about 2001 Ford Explorer Sport Trac

Open Question

2001 sport trac bcm location

Wipers dont work replaced motor & switch checked fuses and relays.Also entry light doesnt work when door opens nor the seat belt warning.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2001 ford windstar speedometer doesnt work or trac controle

hello i think it is the speed sensor because it operates the speedometer and this why the abs lights came on i had the same problem it should work.

Posted on Feb 17, 2009

  • 1 Answer

SOURCE: 2001 ford explorer sport trac

Just found the answer on another site. Sure enough went out removed the 3 philips head screws in the steering column opened it up and walla a wire connection had pulled itself free. When my son uses my truck he always uses the tilt steering, when I get in I have to readjust it. because of this the wire connection pulled itself out. I simply pushed it back in an blinker and brake light are now working. My husband is now trying to figure a way to secure the wire connection so it doesn't pull itself out again. Hope this helps others, either by saving the cost of a dealership or machanic or from getting rear ended.

Posted on Mar 21, 2009

jagjeffery
  • 318 Answers

SOURCE: ABS fuse locations

There are a total of 5 fuses for brake and abs functions 3 in central fuse box on the drivers side inside truck fuse #9 - 7.5 amp fuse #10 - 10 amp and fuse #11 - 7.5 amp then there are 2 big fuses under the hood in the main battery fuse box next to the battery fuse # 6 - 50 amp and fuse # 28 - 30 amp

Posted on Jun 01, 2009

  • 5 Answers

SOURCE: how to replace fuel filter on 2001 ford sport trac

Buy a manual and read it. The manual will tell you how to replace...

Posted on Nov 23, 2009

satitus
  • 273 Answers

SOURCE: the electric compass and temp. display isnt

I believe that the mirrors and entry issues are not related to the overhead console. Compass/temp failure is a very common problem with many of the mid 2000 Ford truck and SUV overhead consoles. The console is very prone to internal failure. If the dome lights work but the compass unit does not then it is a faulty computer unit. I offer a reasonable repair service with a lifetime guarantee, check it out: www.autoclockrepair.com
There is a bunch of useful info there. Drop me an email if you have questions, thanks!

Posted on Jan 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHERE IS THE WIPER/WASHER FUSE LOCATED ON 2007 PONTIAC TORRENT


In the under hood fuse box , should have diagram inside the lid . Front wiper's or rear ? Front fuse # 36 - 25 amp. Plus Two relay's PCB hi and Wiper PCB relay . Wouldn't think this being fuse problem . Wiper switch , motor etc... The wiper's are control by a computer . BCM - body control module .

The windshield wiper/washer system consists of front and rear wipers. The front and rear wipers are operative when the vehicle is in accessory or run. The front wipers have 4 different modes: Mist, Intermittent, Low, and High. When the front wipers are in the intermittent mode, there are 5 delay modes to chose from, commanded by the windshield wiper washer switch through the body control module (BCM). The rear wipers has an only one mode.

If the fuse is bad , could have a short to ground or wiper motor pulling to much current (amps) . Fuse's don't just blow for no reason ! Could also have DTC'S - diagnostic trouble codes stored in the BCM .
DTC B3715
DTC B3873
DTC B3875
DTC B3922

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
The BCM controls the windshield wiper motor through two output controls, controlling two different PCB relays which control the desired wiper speed, high or low.
DTC B3922 00: Front Wiper Function Select Circuit

The PCB relay's are non- servicable , replace fuse box . Soldered in Your best bet mit be to take it to a qualified repair shop .

Feb 20, 2017 | Pontiac Cars & Trucks

3 Answers

Its a 1997 montero sport


it could be the actual motor burnt out or siezed wich is causing the fuses to blow and the motor is under the bonet just below the windowscreen near the top vents.

Jul 25, 2008 | 2000 Mitsubishi Montero Sport

1 Answer

Wipers dont work


This is a complex wiper system . Here are all the components involved !
The Wiper/Washer System consists of the following components:
?€¢
Windshield wiper/washer switch


?€¢
Body control module (BCM)


?€¢
Wiper 1 relay


?€¢
Wiper 2 relay


?€¢
Wiper diode


?€¢
Windshield wiper motor


?€¢
Windshield washer pump


?€¢
Windshield washer nozzles


?€¢
Windshield washer solvent container


?€¢
Windshield wiper arm and blade assemblies


?€¢
Windshield wiper transmission


?€¢
WIPER/SW 10A fuse


?€¢
WIPER 25A fuse


Circuit/System Description
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation. The windshield wiper motor park operation is controlled by the BCM. The BCM recieves an input from the park switch to determine wiper blade position. When the wiper blades are at the bottom of the windshield glass in park position the wiper park switch will open and the circuit will be pulled up to B+ by the BCM. The park signal will be pulled to ground by the wiper motor park switch while the wiper blades are not in the park position.
The BCM controls the windshield wiper motor through two output controls, controlling two relays which determine the desired wiper speed, high or low
Diagnostic Trouble Codes (DTCs)
The body control module (BCM) monitors the voltage on the windshield wiper switch signal 2 circuit for diagnostic purposes. If the circuit is shorted to voltage while the driver is commanded OFF, the BCM will store DTC B3715. If the circuit is shorted to ground while the driver is commanded ON, the BCM will store DTC B3715. Refer to DTC B3715.
It would be best to have a factory scan tool to diagnose this problem . it would make it easier anyway .
It

Dec 05, 2015 | Cars & Trucks

2 Answers

2007 Kia Sportage Front Wheel Drive 4 cyl, Automatic. Rear window wiper suddenly failed. Power to motor checked and confirmed, but once it is mounted, it quits. New motor mounted, same problem. All fuses...


Not sure about your car, but on my Chrysler mini van the same problem happened. The problem was not the motor but the body control module. The unit had 2 relays, but the BCM actualy controls the unit. To replace the BCM was $450. I bypassed the problem by installing an on/off switch inside the car and activated the motor by by passing the BCM at the relay. That was 3 years ago, still works great. Your BCM may be the problem. Check the schematics of the relays and try doing the same.

If you don't have the manuals, your local library has online access to most service manuals that you would have to pay for. Many time you can get access to them through their website if you have a library card. If not, go the library and get full free access to all the major car service manuals for free!

Jan 01, 2015 | 2007 Kia Sportage 2.0

1 Answer

Replace a relay for rear wiper 2001 Ford Explorer Sport


the relay is a fuse,check under your hood for fusebox

Jan 12, 2013 | 2001 Ford Explorer Sport

1 Answer

My horn and code entry does not work on my 2001 Ford Explorer sport Trac. Where is the fuse if there is one,or how do I fix this


horn fuse should be under the dash. you may also want to check relays under the hood. They are in a block box labeled relays. Check under the dash first. There should be a diagram for the fuses in the owners manual or located near the fuse panel. The fuse block should be up above the brake

May 18, 2011 | 2001 Ford Explorer Sport Trac

2 Answers

1993 Dodge Dynasty. Wipers stopped working. Replaced fuse. Still not working. Replaced Body Control Module(BCM) located inside kickboard(passenger side). Still not working. Tried a second BCM, didn't...


BCM's are part number specific to your particular vehicle so unless you got from a dealer and had the dealer flash it for you none will work.

Caravan's had the same problem with their bcm's

Did you test the motor to see if it was working before you got the bcm's?

Did you test the wiper motor switch?

Also test the wiper motor relay.

Apr 01, 2010 | 1993 Dodge Dynasty

1 Answer

The winshield wipers doesnt work,looking for the relay,where is locate it?


THIS ALSO HAS A FUSE,CHECK IT FIRST,CHECK ALL THE CONNECTINGS LEADING TO AND FROM THE WIPER SWITCH & MOTOR

Oct 28, 2009 | 1997 Mitsubishi Montero Sport

1 Answer

THE AUTO DOOR LOCK AND POWER WINDOW DO NOT WORK AND I CANT FIND THE FUSE FOR THEM ON 2005 NISSAN ALTIMA


From the service manual, which is available relatively inexpensive at Promanuals.net here

 Both front wiper relays are located in the IPDM E/R (intelligent power distribution module engine room)
 Wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input terminals.
Terminal combination status is read by BCM (body control module)
 BCM controls front wiper LO, HI, and INT (intermittent) operation
 IPDM E/R operates the wiper motor according to CAN communication signals from the BCM.
Power is supplied at all times
 through 50A fusible link (letter f , located in the fuse and fusible link box)
 to BCM terminal 70, and
 through 20A fuse (No. 39, located in the IPDM E/R)
 to front wiper relay, located in the IPDM E/R
With the ignition switch in ON or START position, power is supplied at all times
 through 10A fuse [No. 1, located in the fuse block (J/B)]

Sep 28, 2009 | 2005 Nissan Altima

1 Answer

2001 ford explorer sport-trac rear power window doesnt roll up


do all your other power windows work???? yes then it is the rear window switch or the power window motor... if all windows don't work then relay or fuse

May 13, 2017 | 2001 Ford Explorer Sport Trac

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...