Question about 1998 Chrysler Town & Country

Open Question

Location of blend door in 1998 Chrysler town and country

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 79 Answers

SOURCE: power door locks on 2005 chrysler town and

There is an ecu flash for this repair. You may get the locks to start working again with a battery disconnect.

Posted on Jun 18, 2010

Ad
emissionwiz
  • 76070 Answers

SOURCE: i have a problem with power sliding doors on 2001 Chrysler Town and Country limited

do you mean they are sticking?

Posted on Oct 20, 2008

  • 117 Answers

SOURCE: 2005 crank position sensor location

The crank shaft sensor on that model should be on the driver side towards the back of the tranny its not hard to get to.

Posted on Jun 27, 2009

ftw1952
  • 10319 Answers

SOURCE: how to reset the alarm system on a 1998 chrysler

Information can be found FREE by downloading a FREE SERVICE MANUAL for your vehicle using the link below

http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

Posted on May 02, 2010

  • 2926 Answers

SOURCE: need location of crank sensor

You did not mention the engine size you have, but the sensor is mounted on the trans housing and will look like this on a 3.8 liter engine.

53001aa.jpg

Posted on Jul 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How toChange blend actuators on Chrysler town and country 2009


REmove screws from old actuator. Unhook from linkage/door. Install new actuator and screws.

Aug 21, 2017 | 2009 Chrysler Town and Country

1 Answer

Need diagram for juntion box


Thread: fuse box?? - The Chrysler Minivan Fan Club Forums

forum.chryslerminivan.net/showthread.php/21174-fuse-box

Jun 26, 2011 - 10 posts - ‎3 authors
Does anyone have a diagram for the fuse box (junction box) that is inside on the drivers side for a 1998 Town and Country. I need to know what the relays are for, my manual only shows the fuses and there is ... Forum · The Minivan Mopar Garage · 3rd Generation Chrysler Minivans: 1996-2000; fuse box?Missing: juntion

Interior Fuse Box Location: 1996-2000 Chrysler Town and ...

www.carcarekiosk.com/video/2000_Chrysler_Town_and.../replace
Interior Fuse Box Location: 1996-2000 Chrysler Town and Country ... box of your 2000Chrysler Town and Country in addition to the fuse panel diagram location. ... If youneed to replace a blown fuse in your Town and Country, make sure you ...Missing: juntion

Dec 21, 2015 | 1996 Chrysler Town & Country

1 Answer

2005 chrysler town & counry constantly blows hot in front


I'd lean more toward the blend door actuator. I've experienced that problem more often with Grand Caravans (aka Town and Countries) and Pacificas. Usually, if it's a resistor, it's the blower motor resister, which means you wouldn't get any air movement at all.

The only thing I can't recall off hand is if Chrysler services the actuator separate from the blend door housing on these models. However, I'm sure that's what you will need as the blend door is what regulates the mixture of cool and hot air. Keep in mind this is not the mode door actuator or housing. That's something completely different that directs the air to different paths (vent, floor defroster, etc.)

Contact Chrysler as I believe these are only available OEM last I checked.

Aug 23, 2012 | 2005 Chrysler Town & Country

1 Answer

2007 chrysler town and country a/c blows cold through floor and defrost vent but not dash vents


Often a sign of a blend door problem. The blend door or doors are in the heater a/c box behind the dash.

Jun 28, 2012 | Chrysler Town & Country Cars & Trucks

2 Answers

My wifes minivan, 2001 chrysler town and country does not blow very cold air. it's cool but not cold. I have replaced the dryer and recharged system to 2.69lbs. It holds vacuum and the guages are in...


Did you pull a vacuum on the system before charging? Disconnect the blend door actuator and turn it by hand. These aren't known for having stuck blend doors.

Jul 12, 2017 | 2001 Chrysler Town & Country

1 Answer

My 2001 Chrysler Town and Country heater is working fine on the driver side, but blows out cold air on the passenger side. Help


I have seen this quite a bit. This issue is caused by the blend door for the climate control system. Those doors were not that well constructed and end up breaking to the point where the climate system can no longer operate the door. This can be a very difficult to repair because it requires dash removal to get access to the appropriate door. This condition can easily be verified by a dealer test with scan tool. If you would like to replace yourself I would recommend contacting dealer for a copy of the removal and repalcement procedure for the passengers blend door. I hope this information was helpful.

Feb 22, 2011 | 2001 Chrysler Town & Country

1 Answer

Driver side blows hot air. passenger side blows cold air


There are separate blend doors for the passenger and driver's side. The blend doors divert, not block air, so it is unlikely that the blend doors are the problem. Your mechanic needs to check the operation of the re-circ door and if its fault replace it.Thanks. Hope you rate my response


Feb 03, 2011 | 2000 Chrysler Town & Country

1 Answer

Why does my 2002 town and country blows cold air on the passenger side and i have no floor heat in either driver or passenger sides?


These vans have a bad design on the heater blend door which is located on the heater box behind the dashboard. The hinge on the blend door breaks and will not move causing the air not to circulate through the heater. Do you hear any clicking noise? You may get lucky with a repair. Go to the eBay site and in search put in-blend door repair-
Good luck and thanks for your question and I hope my suggestions help. Don't forget to rate me.
burdfrenzy
Visit My eBay Store!
http://stores.ebay.com/Pittsburgh-Joes-Pants-Nat

Jan 07, 2011 | 2002 Chrysler Town & Country

1 Answer

My heat stopped working in my 2000 town and country van and I have no idea why...any suggestions? Thanks In wi and it's freezing


If it happened suddenly, it is probably the blend door actuator.

Please see my tip at http://www.fixya.com/cars/r6235876-no_heat_fan_blowing_cold_air . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Your blend door actuator is above the accelerator pedal. See picture below.
jturcotte_517.gif

Dec 15, 2010 | 2000 Chrysler Town & Country

1 Answer

Heat on, blows cold air on passenger side


u will need to repair the passenger side air temp control blend door, either the door is stuck or the small electric actuator that moves it is defective.

Jan 14, 2009 | 2004 Chrysler Town & Country

Not finding what you are looking for?
1998 Chrysler Town & Country Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...