Question about Seat Ibiza

Open Question

Torque Setting For Front Wheel Hub Seat Ibiza 1.2 3,Cylinder Petrol,

I'm LOOKING!! For The Torque Setting For The Front Wheel Hub On A Seat Ibiza 1.2 3,Cylinder,Petrol

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Torque specs for front wheel hub nut

112 to 174 ft lbs

Posted on Apr 04, 2009

seanpwright
  • 2030 Answers

SOURCE: What is the proper torque setting on the wheel

95-105 ft/lbs.

Posted on Oct 31, 2009

Testimonial: "I thank YOU !!! after I had ask 10 area mechanics and they all said gee i'm not sure. ^5 to YOU grinchsdawg"

johnjohn2
  • 5763 Answers

SOURCE: what is the torque setting on a gmc jimmy 1999

the torque for the outter axle nut at the wheel for a 1998 gmc jimmy is 103 ft lbs. hope this helps.

Posted on Jun 15, 2010

jebild
  • 178 Answers

SOURCE: what is the torque setting for the wheel bearing

there's a manual here: http://myweb.dal.ca/is353832/93fsm/

Posted on Jul 07, 2010

  • 1 Answer

SOURCE: Torque setting for a 1999

To be honest, i just follow the torque settings of the 2.8 engine as the bolts are the same size and thread. 78nm 90o 90o.

Posted on Feb 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i fix


drain the siump and check for metal in the oil
if so then it is bearing failure or major engine damage

Sep 30, 2016 | Seat Cars & Trucks

1 Answer

Seat ibiza faults


Check alternator charge rate and earth straps

Jun 19, 2014 | 2007 Seat Ibiza 1.2

1 Answer

Seat ibiza cylinder head torque settings


I am sorry we have info on all USA models and some common eurozone models like VW, Audi etc. This is not a common make and we have no info on it. Sorry

Feb 19, 2012 | Cars & Trucks

1 Answer

What is needed to remedy right hand front wheel bearing play on a 1990 d21 4X4 ute


replace the bearing or wheel hub assembly.

REMOVAL & INSTALLATION 2wd Models NOTE: Refer to wheel bearing service and bearing preload adjustment procedures found in Section 1.
  1. Raise the front of the truck and support it with safety stands. Remove the wheels.
  2. Remove the brake caliper and suspend it with wire, out of the way. Remove the caliper torque plate if equipped.
  3. Remove the dust cap and then remove the cotter pin, lock washer (if equipped) nut lock and nut.
  4. Pull the hub/disc assembly off the spindle with the outer bearing. Don't let the bearing fall out.
  5. Pry the inner oil seal out and remove the inner bearing. To install:
  6. Clean and inspect the bearings and outer races.
  7. Using a brass drift and a hammer, drive out the bearing outer race. Press a new one into position.
  8. Pack the bearings with grease until it oozes out the other side. Coat the inside of the hub and cap with grease.
  9. Position the inner bearing into the hub, coat the oil seal with grease and press it into the hub.
  10. Press the hub assembly onto the spindle and install the outer bearing and thrust washer.
  11. Install the hub nut. Turn the hub a few times to seat the bearings and then loosen the nut until there is 0mm axial play. Using a spring tension gauge, check that the preload (with new grease seal installed) is 2.2–6.4 lbs. (9.8–28.4N)
  12. Install the lock-nut, new cotter pin and hub grease cap.
  13. Install the brake torque plate. Install the brake caliper.
  14. Install the wheels and lower the truck.
4wd Models The hub and bearing service procedures for a 4wd models are basically the same as those for a 2wd version, with the exception of removing the free running hub assembly and the bearing preload adjustment. Refer to Sections 1 and 7 for additional information. Adjust the preload after the wheel bearing is replaced or the front axle assembly is reassembled. BEARING PRELOAD ADJUSTMENT
  1. Thoroughly clean all parts and pack the wheel bearings.
  2. Apply grease to threaded portions of the spindle, grease seal lip and wheel hub.
  3. Tighten the wheel bearing lock-nut with a socket and torque wrench to 58–72 ft. lbs. (78–98 Nm).
  4. Rotate the hub in both directions a few times to seat the bearings. Loosen wheel bearing lock-nut.
  5. Retighten the lock-nut to 0.4–1.1 ft. lbs. (0.5–1.5 Nm).
  6. Turn wheel hub several times in both directions.
  7. Retighten the lock-nut to 0.4–1.1 ft. lbs. (0.5–1.5 Nm). Fig. 1: Exploded view of the front axle assembly — 2wd models 86718030.gif
    Fig. 2: Removing the bearing outer races 86718032.gif
    Fig. 3: Packing the wheel bearing with grease 86718033.gif
    Fig. 4: Pack the lip cavity of grease seal with grease 86718034.gif
    Fig. 5: Exploded view of the front axle assembly — 4wd models 86718031.gif

  8. Measure wheel bearing axial end-play. The wheel bearing end-play specification is 0.
  9. Install lock washer by tightening the lock-nut within 15–30 degrees.
  10. Turn wheel hub several times in both directions. Wheel bearing should be seated correctly.
  11. If necessary, measure wheel bearing preload. NOTE: Measure wheel bearing preload with a spring-type gauge; measure at wheel hub bolt, with tire removed. The hub assembly should rotate with 1.6–4.7 lbs. (0.73–2.13 kg) of pressure.
prev.gif next.gif

Jul 28, 2010 | 1991 Nissan Pickup

1 Answer

Is there a Haynes Manual for the 1.0L Seat Ibiza, 2000 version?


There is a haynes manual for 2000 on. All Fiat/ Seal have minor differences. I think that yours is probably the one that you have to remove the hub nut to take off the hub.

Jun 09, 2009 | 2000 Volkswagen Golf

1 Answer

Torque setting for grand am rotors


The rotors are not bolted to anything, they are sandwhiched between wheel & hub. Therefore there is no specification for them. Caliper bolts are 38lbs if that's what you were looking for.

Apr 09, 2009 | 2003 Pontiac Grand Am

2 Answers

Torque Setting for the Wheel Berring Nut


Is this a 4x4 or 2 wheel drive?If its 4x4 its 150flbs and 2 wheel drive its tightened by hand until slop or wobble is gone.

Mar 30, 2009 | 1999 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Seat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Adam Truesdale

Level 2 Expert

265 Answers

Are you a Seat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...