Question about 2006 Chrysler PT Cruiser

Open Question

How to replace an ignition switch on a 2006 pt cruiser?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: PT Cruiser Brake Light

The bulb in the rear light has burned out and to replace it follow these instructions: 1) go to your owner's manual to find out the part number. You can find and purchase the replacement bulb at Target, any auto parts store and even at Walmart for under $4.00; 2) pop open the trunk door; 3) get a phillips screw driver and unscrew the 2 screws holding the rear brake light fixture to your car body; 4) as soon as you turn over the fixture you'll see where to pull out the burned out bulb and replace it with the new one(s). Good luck!

Posted on Oct 15, 2008

  • 1 Answer

SOURCE: 2001 PT Cruiser quit running driving down highway

I HAD THE SAME PROBLEM, I BROKE A TIMING BELT.   HAD TO REPLACE THE ENGINE.

Posted on Mar 22, 2009

BCAS1298
  • 3092 Answers

SOURCE: replacing a starter in a PT. Cruiser 2001

Remove battery and battery support you'll be able to undo starter bolt's trough there and slip starter out.

Posted on Dec 08, 2009

Testimonial: "This didn't help, because you had to remove the engine structural collar under the starter to get at the starter bolt. It was more complicated."

  • 2309 Answers

SOURCE: 2007 PT Cruiser basic RAD fan battery relay feed replacement

grt one at any parts store, it should be in the fuse or electrical box, look in the owners manual, pull out the the ole and plug in the new

Posted on May 08, 2010

  • 5 Answers

SOURCE: 2001 PT Cruiser: How too remove crankshaft pulley 2001 PT Cruiser...

GET A 3 SPOKE PULLEY EXTRACTOR AND SCREW IN THE BOLT BUT IN THE CRANKSHAFT HOLE PUT A MUCH SMALLER SCEW SO YOU WOUNT MESS THE INSIDE UP

Posted on May 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2006 pt cruiser shut off while driving and won't restart?


Possibly the ignition switch. I had weird issues happiness with mine like that. I took it to the dealer and they quickly determined that the electrical part of the ignition switch had failed. They told me that thus is not uncommon in pt cruisers. They replaced it and all was well in the world.

Oct 15, 2014 | 2006 Chrysler PT Cruiser

1 Answer

Pt cruiser cranks but won't start


Did you check to see if there is a neutral safety switch on the transmission?

Feb 02, 2014 | 2006 Chrysler PT Cruiser

1 Answer

How to replace clutch ignition lock switch


Clutch ignition switch?? Not sure what you are referring to please clarify. Do you mean clutch safety switch?

Aug 18, 2012 | 2006 Chrysler PT Cruiser

2 Answers

2006 PT Cruiser. All dash light indicators flash on and off and all gauge needles fluctuate simultaneously. Sometimes when this happens the car stalls. The dealership can't find the problem. Does


I just had the same problem happening with my 2006 PT Touring. Took it to the dealership. The issue was the electric parts of the ignition switch. They replaced it and all is well in the world again.

Jun 18, 2012 | 2006 Chrysler PT Cruiser

1 Answer

Where is fuel reset switch or fuel relay on 2006 pt cruiser located


Relieving Fuel System Pressure

Print

CAUTION Relieve the fuel system pressure before servicing any components of the fuel system. Service vehicles in well ventilated areas and avoid ignition sources. NEVER smoke while servicing the vehicle!

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the fuel pump relay from the Power Distribution Center (PDC).
  3. Start and run the engine until it stalls.
  4. Turn the ignition key to the OFF position

May 08, 2012 | 2006 Chrysler PT Cruiser

1 Answer

My low light dosn't work in pt cruiser 2006


You will need to replace the headlight dimmer switch.

Apr 06, 2012 | 2006 Chrysler PT Cruiser

1 Answer

What is the code B212F for pt cruiser 06.


B212F - Ignition RUN/ACC control circuit low
The controller of the cruise control is defective and must be replaced.

Sep 27, 2010 | 2006 Chrysler PT Cruiser

1 Answer

I need information on replacing the windsheild wiper switch on my 2006 Chrysler PT Cruiser


it is actually called the multifunction switch

fairly simple...
  • disconnect battery, but make sure you have your radio code or have installed a memory saver
  • remove shroud around steering column
  • disconnect multifunction switch
  • unbolt switch
  • replace switch
  • reverse to install

3b150c5.gif



Jun 03, 2010 | 2006 Chrysler PT Cruiser

Not finding what you are looking for?
2006 Chrysler PT Cruiser Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...