Question about Chrysler Sebring

Open Question

My 2004 chrysler seabring has no injector pulse fuse # 24 in the PDC has power for a second or two then it loses power . is it supose to ?

It has no injector pulse exsept for #1&6

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 740 Answers

SOURCE: 1993 honda accord 2.2,no injector pulse

This sounds like a main relay problem here is a diagram its located under the dash under steering column its the brownish -orange box in the picture. http://www.tegger.com/hondafaq/mainrelaylocation/7-main_relay_closeup.jpg Good luck and thanks for using FIX YA

Posted on May 15, 2009

Ad
redbeard00
  • 957 Answers

SOURCE: no power tp the fuel pump, injectors not pulsing, no fuel.

Check out your oil sending unit, fuel pump and relay, check for power (might be a fuse), the ignition control module (which if you remove it, can be tested for free at AUTO-ZONE), any related wiring, pick-up coil (inside the distributor), and possibly the ignition switch. If I can be any more help just as away.

Posted on Jun 06, 2009

dj_relly999
  • 4070 Answers

SOURCE: Describe your 2004 Chrysler Town &

u may try checking the wirings of the front blower, it may be corroded thats why its losing contact, hope this helps

Posted on Jul 03, 2009

  • 1 Answer

SOURCE: no injector pulse but power to injectors good fuel pressure good

did you disconnect the battery before you welded the exaust. other wise the ecu has had it

Posted on Aug 03, 2009

ZJLimited
  • 17970 Answers

SOURCE: how to install a power steering pump for a 1997

Chrysler Cirrus/Stratus/Sebring/Avenger/Breeze 1995-1998
Power Steering Pump - REMOVAL & INSTALLATION

Cirrus, Stratus, Sebring Convertible and Breeze
(see Figures 1, 2, 3 and 4)

  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with an insulator grommet, which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Siphon as much power steering fluid out of the reservoir as possible.
  3. Raise and safely support the vehicle.
  4. Remove the right front tire and wheel assembly.
  5. Remove the splash shield from the right front wheel well.
c901554.jpg

Fig. 1: Power steering pressure hose attachment to the pump-with Variable-Assist steering

8786c07.jpg

Fig. 2: Power steering pressure hose attachment to the pump-without Variable-Assist steering
  1. Disconnect the power steering pressure hose from the pump.
  2. Remove the hose connection on the power steering pump.
e7733b2.jpg

Fig. 3: Typical power steering pump front bracket attachment
  1. Remove the power steering adjusting bolt.
  2. Remove the power steering pump rear attaching bolt.
  3. If so equipped, remove the Anti-lock Brake System (ABS) hydraulic control unit heat shield.
  4. Remove the wheel speed sensor retainer bracket from the right inner fender.
  5. Remove the wheel speed sensor sealing grommet from the right inner fender.
  6. Disconnect the speed sensor wiring.
  7. Push the wiring through the hole in the inner fender.
If not equipped with anti-lock brakes, the hole will just have a sealing plug.
  1. Remove the bolt attaching the power steering front bracket to the mounting bracket. Access to the bolt is gained through the hole for the speed sensor wiring.
  2. Remove the power steering pump drive belt.
  3. Remove the power steering pump and the front bracket as an assembly.
To install:
  1. Install the power steering pump and bracket.
  2. Reinstall the bolt at the adjusting slot, but do not tighten.
  3. Reinstall the bolt mounting the power steering pump to the rear mounting bracket, but do not tighten.
  4. Reinstall the power steering pump top bolt, but do not tighten.
  5. Reconnect the power steering hoses.
b72b14a.jpg

Fig. 4: Install a new O-ring gasket on the hose fitting
Use a new O-ring when reinstalling the power steering pressure hose.
  1. Reinstall the drive belt.
  2. Adjust the drive belt and tighten the power steering pump bolts to 40 ft. lbs. (54 Nm).
  3. Reinstall the splash shield.
  4. Reinstall the tire and wheel assembly.
  5. Lower the vehicle.
  6. Reconnect the negative battery cable.
  7. Refill the reservoir and bleed the power steering system.


Sebring Coupe and Avenger
  1. Disconnect the negative battery cable.
  2. Remove (drain, suction pump, etc.) as much power steering fluid as possible.
  3. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.
Cover any components located underneath the power steering pump with a shop towel to protect them from damage due to power steering fluid spillage. For example, the A/C compressor or alternator, depending on vehicle and engine, is below the power steering pump, so cover the A/C compressor or alternator with a shop towel before removing any hoses.
  1. Loosen (but do not remove) the power steering pump mounting bolts and remove the drive belt.
  2. Remove the pressure switch connector from the side of the pump.
  3. Disconnect the pressure line.
  4. Unbolt and remove the pump from the mounting bracket.
To install:
  1. Clean all parts well. Inspect the pump pulley for cracks. Check the hoses carefully for cracks or signs of weakness.
  2. Install the pump, wrap the belt around the pulley and lightly tighten the mounting bolts.
  3. Replace the O-rings and connect the pressure line. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the fitting to 13 ft. lbs. (18 Nm).
  4. Connect the return line and secure with the clamp.
  5. Fasten the pressure switch connector.
  6. Adjust the power steering belt for proper tension and tighten the adjusting bolts.
Use only MOPAR ATF PLUS automatic transmission fluid type 7176, ATF+3 automatic transmission fluid, or equivalent, in the power steering system of Sebring coupe and Avenger models.
  1. Refill the reservoir and bleed the power steering system.

Hope this help to solve it (remember comment and rated this). TY for using Fixya.

Posted on May 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 sebring 24 no fire no codes new pcm


You have power to coil but do you have the pulse's needed for the spark

Jun 03, 2016 | 2004 Chrysler Sebring

1 Answer

Im looking for the ECU fuse on a 2006 jeep commander under dash what fuse is it?


the cars electrics are complex. as is the ECU (now called a PCM)
the PCM has up to 3 to 4 fuses.
typically 1 for spark, 1 for fuel and 1 for PCM and one more for the ecu memory fuse, that if pulled clears the PCM errors (DTC:)
all this is in the FSM.book (factory, serv. man)
btw if the PCM CEL lamp is dead, that be the PCM main fuse.
also part of MAIN relay on all cars with EFI and the ASD relay.
in 2007 jeep wiring changed radially, so.... something to consider and know that they some times do that gradually.
is this a gas engine,? there are 3 gas engines, (sizes)
the engines size also dictates which PCM you have.
sure wish i had just a clue as to a symptom so i dont have to read the full wiring tree..... 32 page in the fsm on fuse/spark alone.

JB fuse 24, to pCM. (jb means cab box
) PDC means engine bay. MIP box has power feed to PCM too on pin 12 (more later )

PDC fues 6. for ASD main.
PDC fuse 28 the injectors.
PDC fuse 16, coil spark.
i missed some, as i did not see the hot all the time fuse (mem)

ah, pdc fuse 20 is PCM memory. found it.
page 2 is missing on my source, so....

the PCM also does the job of TCM to shift some transmissions.
and that may have its own fuses too.

May 06, 2015 | 2006 Jeep Commander

1 Answer

Where do I find the downstream 02 sensor on a 2004 2.4l seabring


I have no specific model experience but the downstream or diagnostic O2 sensor is generally found screwed into the exhaust system just after the catalytic converter.

Feb 28, 2015 | 2004 Chrysler Sebring

1 Answer

Hello i have a 2004 chrysler seabring wippers and turn signals dont work fuse is ok


Replace the turn signal switch. Remove the column bezel. Screws on the bottom. A couple of screw to remove the switch. When replacing the switch, make sure you push in the horn button. before you screw it back in.

Feb 21, 2015 | 2004 Chrysler Sebring

1 Answer

No injector pulse on daewoo nubira i change computer box but still no pulse wot must i look for or replace


Check for an injector fuse in the fuse box under hood. Pull off one injector connector and use a testlight to check for a steady power signal on one of the two wires, with key on. Should have power on one wire. If not, pull all injector connectors off and check again-a shorted injector can shut down the injector drive circuit-if power now, reconnect injectors one at a time. If one connection causes power to be lost, that is a shorted injector. Replace it. If still no power and fuse is good, you will need a wiring diagram to check injector drive circuit.
If you have voltage at the injectors with key on, move the test light ground lead to the battery positive post, and put the test light probe on the injector wire that did not light the test light. Now have a helper crank the engine over-you should have a blinking light on this ground circuit. If no light, or light is not blinking, the ground circuit between injector and computer is bad. See? Steady power is available to injector anytime key is on. When the computer internally grounds the injector circuit for a split-second, the injector is energized, causing the pulse.

Mar 22, 2013 | Cars & Trucks

1 Answer

Draining fuel from 2004 crysler seabring.


Just go buy some fuel stabilizer and top off the tank and drive. Two years isnt that bad. Then on the next tank use some injector cleaner. I like chevron techron fuel injector cleaner added to a full tank of prem 91. This is just a prevenitve measure to clean any varnish that may accumulated on the injector nozzles.
Then use 87 octane if thats what you normally use.

Jan 12, 2010 | 2004 Chrysler Sebring

1 Answer

No electric pulse to injectors on 1994 ford f350 diesel turbo 7.3


Im confused how do you have a direct inject diesel in a truck made 3 years before ford had such a thing 94(suposed to ) has a indirect inject diesel there is no electric wires running to the injectors there's only a pipe with very high pressure fuel running thru it
are you sure your not confusing the glow plug wires ?
they only get power to them for like 30 seconds when first starting it

whats the real problem?

Oct 27, 2009 | 1994 Ford F350 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...