Question about Nissan Cars & Trucks

Open Question

Stop lights not working on nissan interstar van

The lights were working fine and now stopped the fuse seems to be ok any ideas????

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
leetamara
  • 702 Answers

SOURCE: The gauges have stopped working ? Fuse under dash seems to be OK ?

Behind the dash is what they call a constant voltage regulator. It controls the guages. It's small and located behind the dash near speedo.

Posted on Jun 19, 2008

Ad
  • 1 Answer

SOURCE: low beam headlights not working on 2004 Pontiac Montana extended

You headlight lamp have a diffuser mechanism which allows it to flip between the hight beam and low beam feature of the bulb. In fact, you high beam will function even if the low beam is not working.

I would recommend the purchase of the new headlight lamp. It would cost you you any where from $15.00 per unit to get a replacement lamp

Posted on Jan 06, 2009

  • 109 Answers

SOURCE: 2002 Nissan Quest speedometer - not working

Its most likely related. Vehicle speed sensor is bad

Posted on May 06, 2009

  • 85 Answers

SOURCE: 98 Chevy pickup brake lights just stopped working

have you tried to find the brake pedal switch? follow the brake pedal under the dash and there should be a switch that the brake pedal presses to activate the lights when you push it in . if everything else has been checked then I suspect that the switch has moved enough to not work or it may be just bad. let me know if this was it.... hope this works

Posted on Jun 17, 2009

  • 5 Answers

SOURCE: 2002 Nissan Quest speedometer not working

Take the VSS unit out as described. Need two people. Have the unit out of transmission but hook up the electrical wire. Turn the ignition ON but do not start the engine. Turn the gear while someone watches the speedometer. If you get a response then just replace the gear and try it. The gear may not look worn or broken but just a little wear and it looses contact with the transmission worm gear. This may cost you about $6 instead of over $60.

Posted on Jul 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Horn has stopped working on my 2006 Ford Explorer. The fuse seems to be fine. What could be the problem?


I would suspect an underhood fuse, the steering wheel clock spring, or a wiring problem. It's cheap to triple check all the fuses. The other two will require some troubleshooting to figure out. Since the horn works with the keyless entry, the relay, the horn, and its control wiring seem to be ok.

Sep 20, 2014 | 2006 Ford Explorer

1 Answer

Nissan terstar dci 120 not starting flashing red stop light


no year, now that makes for a long story, huh?
what is a terstar?
you ment , INTERSTAR (so says google.)??????
a VAN.
ouch wiki is only in German....
2003-10 (transated)
Analogous to the revision of the Renault Master II / Opel Movano I also received the Interstar 2003 a revision of the body, engines and interior. Since then, an automated manual transmission (Interstar X70) was for the revised model now available and optional ESP (vehicle dynamics control) available. Also belonged from now a Brake Assist besides the previously installed anti-lock braking system standard on all models. Since then, the Interstar has been delivered as a minibus with up to 16 seats. 2010, the Interstar was replaced by the Nissan NV400.

NO START.
but to start any DIESEL engine,
IT MUST Crank first. does it?
if NOT, the the battery is dead, or bad. (or discharged)
DOes jumper cables used, (donor car) crank engine now?
if it DOES, crank, and robustly, then Id bet the glow plugs are bad.
if not glow plugs, lack of FUEL , ever change the filters per schedule>?

open glove box, extract the operators guide, I PROMISE
it tells you what the RED lamp means..
if lost , get one. from NISSAN , they are free.

Jul 04, 2014 | Cars & Trucks

1 Answer

No head & frog light.


Check the main light header fuse.

Mar 12, 2014 | Toyota Camry Cars & Trucks

1 Answer

Air bag light stays on, on nissan interstar 2004 panal van


usually bad connections under the seats ... need a diagnostic code to help more

Nov 22, 2013 | Cars & Trucks

1 Answer

Nissan Xterra Brake Light Fuse Location


It's 15A FUSE 39 in the fuse & fusible link box

Mar 25, 2017 | Nissan Xterra Cars & Trucks

1 Answer

My nissan interstar van wont start like battery dead and its charged fully


Battery with a dead cell can still show 12.5-13.8 volts but when any draw is put on it will drop voltage like a rock such as cutting on the headlights. They may look ok to begin with but will dim very quickly. I would start here by having the battery load tested.

Jan 12, 2013 | Cars & Trucks

1 Answer

My break light fuse keeps blowing in my 97 suburban any ideas why


Assuming it's a K1500, 15A STOP/HAZ fuse 1 in the instrument panel fuse block is the source of power. If the stop lamp switch checks OK, and the center high mount stop lamp is OK, the cruise control system gets input at this point and may be defective. Fuse 1 also feeds power through the turn/hazard switch to the stop filaments of the tail/stop/turn lamps and these presumably are OK

Sep 22, 2012 | 1997 Chevrolet Suburban

1 Answer

No brake lights, blubs and fuses ok. center brake light DOES work


Usually when the third brake light works but the regular lights don't the problem is in the turn signal switch.
I would check for voltage there.

Jul 19, 2012 | 2004 Jeep Grand Cherokee

1 Answer

Need a free manual for nissan interstar van


Go to www.busytrade.com,believe you come back with fruitful results!

Apr 28, 2012 | 2004 Nissan Nissan almera tino

1 Answer

Mazda Protege 2000 - low beams stopped working, high beams are fine, I replaced bulb and the fuses seem to be OK too? Any ideas? Thanks a lot!


turn signal switch needs changing, it only has 1 or 2 screws that hold it in there. the dimmer is bad

Sep 10, 2011 | 2000 Mazda Protege

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...