Question about 2005 Jeep Liberty

1 Answer

Procedure to change drive belt on 2005 jeep liberty

Any special tools for release? Can another tool be used?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 152 Answers

Im assuming your speaking of a serpintine belt that has a automatic tensenior pully. yes, you can use a 1/2 inch rachet and there will be a place somewhere on the pulley to put it. now you wont have as much leverage as the tool you buy at a part store because it is smaller. hope this help. there should be a diagram right above the belt

Posted on Jan 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Do I need special tools to change water pump on 2005 cadillac cts


  1. You'll need a tool to release the tension on the serpentine belt and when you need to put the belt back on. Regular standard socket wrenches will suffice for the rest.

Oct 02, 2016 | 2005 Cadillac CTS

1 Answer

How do you remove the crankshaft dumper pully?


Published: 11-May-2011
Engine - V8 4.4L Petrol - Crankshaft Pulley
In-vehicle Repair
Special Tool(s)

Holding Tool Crankshaft Pulley
303-893(LRT-12-080)
Adapter
303-191-03
Bolts and spacers
303-191-04
Remover, crankshaft pulley
303-588
Remover, crankshaft seal
303-D121
Installer, crankshaft seal
303-1100
Adapter - Crankshaft seal installer
303-1100-01 Removal
  1. Disconnect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).
  1. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle.
  1. Remove the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).

  1. Remove the cooling fan shroud.
    • Release 2 clips from the cooling fan lower shroud.
    • Release and remove the cooling fan lower shroud from the cooling pack.

  1. Using the special tools, retain the crankshaft pulley.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. NOTE: The crankshaft pulley retaining bolt will be very tight.
    Remove the crankshaft pulley retaining bolt.
    • Discard the bolt.
  1. Remove the special tools.

  1. Using the special tools, remove the crankshaft pulley.
    • Collect the locking ring.
  1. Remove the special tools from the crankshaft pulley.

  1. Using the special tool, remove the crankshaft front seal.
    • Remove the outer section of the seal.
    • Repeat the process to remove the inner section of seal.
  1. Check the crankshaft damper pulley and locking ring for damage.
Installation
  1. Clean all the crankshaft pulley mating faces.

  1. Using the special tools, install the crankshaft front seal.
    • Lubricate the seal with clean engine oil.
    • Use the discarded crankshaft bolt with the service tool.
  1. Install the crankshaft pulley.
    • Lubricate the seal with clean engine oil.
  1. Install the crankshaft pulley locking ring.
  1. CAUTION: The screw thread in the crankshaft pulley must be cleaned out before installing a new crankshaft pulley bolt. Install, but do not tighten, the new crankshaft pulley bolt.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. Using the special tools, retain the crankshaft pulley.
    • Tighten the crankshaft pulley bolt to 380 Nm (280 lb.ft).
  1. Remove the special tools.
  1. Install the cooling fan lower shroud.
  1. Install the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).
  1. Connect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).

Jan 27, 2016 | 2006 Land Rover Range Rover Sport

1 Answer

How To Drain Fuel Tank On 2005 Jeep Liberty Gas Tank


here is the Cherokee page.
read chapter, 14, page 19 on..
shows all way there, and is not easy.
why do this.
is pressure low
pump dead
is there 12vdc to pump cranking, (no? then dont do this)

http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

i have the KJ pages here. (line # messed up)
Two different procedures may be used to drain fuel
tank: through the fuel fill fitting on tank, or using a
scan tool.
The quickest draining procedure involves removing
the rubber fuel fill hose (7) (Fig. 25) from fuel tank
fitting.
As an alternative procedure, the electric fuel pump
may be activated allowing tank to be drained at fuel
rail connection. Refer to DRB scan tool for fuel pump
activation procedures. Before disconnecting fuel line
at fuel rail, release fuel pressure. Refer to the Fuel
System Pressure Release Procedure for procedures.
Attach end of special test hose tool number 6541,
6539, 6631 or 6923 at fuel rail disconnection (tool
number will depend on model and/or engine application).
Position opposite end of this hose tool to an
approved gasoline draining station. Activate fuel
pump and drain tank until empty.
If electric fuel pump is not operating, fuel must be
drained through fuel fill fitting at tank. Refer to following
procedures.
(1) Release fuel system pressure.
(2) Raise vehicle.
(3) If equipped, remove fuel tank skid plate.
(4) Thoroughly clean area around fuel fill fitting
(6) (Fig. 26) and rubber fuel fill hose (1) at side of
fuel tank. After cleaning, loosen fuel fill hose clamp
(2) at tank.
(5) Before removing rubber hose (1) (Fig. 26) from
fitting, note hose orientation while referring to marks
(3) and (4).
6) Disconnect rubber fuel fill hose at fuel tank fitting
(2) (Fig. 27). Using an approved gas holding
tank, drain fuel tank through this fitting.
Tank Removal
(1) If equipped, remove fuel tank skid plate and
tow hooks. Certain equipment packages will also
require removal of the trailer hitch. Refer to Tow
Hooks, Trailer Hitch or Skid Plate in 23, Body for
removal/installation procedures.
(2) Disconnect and separate fresh air tube (6) (Fig.
28) quick-connect fitting.
(3) Disconnect air tubes at front of NVLD pump
(9) (Fig. 28).
(4) Disconnect NVLD pump (9) (Fig. 28) electrical
connector.
(5) Disconnect fuel pump module electrical connector
jumper. This is located near front of fuel tank.
(6) Support tank with a hydraulic jack.
(7) Remove 4 fuel tank strap bolts (10) (Fig. 28) (2
at front of tank; 2 at rear of tank), and remove both
tank support straps.
(8) Carefully lower tank a few inches.
(9) Continue lowering tank while guiding remaining
hoses and lines through plastic isolator sleeve (3)
(Fig. 29).
(10) If fuel tank is to be replaced, remove NVLD
pump and fuel pump module from tank. Refer to
Fuel Pump Module Removal/Installation procedures.
end , tank out.

why not login to alldata.com and read
or buy the FSM,, and get all pages of chapter 14, end to end.

Oct 19, 2015 | 2005 Jeep Liberty

1 Answer

Change timing belt


timing belt? on a Jeep? 05 wrangler
what engine is this>?
ah the 2.4L
front cover
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the crankshaft vibration damper.
  3. Remove the generator drive belt tensioner assembly.
  4. Remove the timing belt front cover bolts, and remove the covers.


rear cover
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the front covers.
  3. Remove the timing belt.
  4. Hold the camshaft sprocket with Special Tool 6847, or equivalent, while removing the center bolt.
  5. Remove the timing belt idler pulley.
  6. Remove the rear cover fasteners and remove the cover from engine.

Apr 04, 2014 | 2005 Jeep Wrangler

1 Answer

Jeep won't go in drive or reverse


bad tranny
check fuses
check tranny level using the operators guide instructions do not guess
do not over fill a tranny

Feb 15, 2014 | 2005 Jeep Liberty Sport

1 Answer

How do I remove the clutch fan on a 2005 jeep liberty?


takes a special tool if ya beat it off can mess up water pump

Sep 08, 2013 | 2005 Jeep Liberty

1 Answer

Can I replace the front diff isolator bushes on my uk 2004 cherokee sport 2.8crd without dropping the front axle?


No-- I doubt you would have room & without seeing what
your referring to ,I think you need special tools to press
them out.

No one,absolutely no one would buy those tools

Maybe a dealer has something the manufacturer
requires a dealership to have

Nov 20, 2012 | 2004 Jeep Liberty

2 Answers

I need to fully remove the front seat in 2005 liberty. I have unbolted the seat but there is a plug under it,(seat belt or air bag) How do i disconnect that plug?


it has either a harness that you have to 'open' a tab to clear a notch, or you need to squeeze it on 2 sides to get ti to slop out of the connector. Use a flashlight to look at it, it will be self-explanatory.

Jan 30, 2011 | 2005 Jeep Liberty

1 Answer

Change timing belt galant 04 mivec 2.4


49885ff.gif
Timing belt “B” (balancer belt) and related components—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


  1. Disconnect the negative battery cable. Remove the engine under cover.
  2. Remove the crankshaft damper pulley.
  3. Disconnect the control wiring harness connector, battery wiring harness connector and connector bracket to engine mounting insulator.
  4. Remove the harness bracket. Remove the upper timing belt cover. Remove the water pump pulley. Remove the idler pulley.
  5. Remove the auto tensioner. Remove the lower timing belt cover.
  6. Turn the crankshaft clockwise and align each timing mark to set the number one piston to TDC of its compression stroke.
  7. Remove the timing belt under cover rubber plug and then install special tool MD998738. Screw the special tool until it contacts the timing belt tensioner arm.

    NOTE The special tool must be screwed in gradually at the rate of a 30 degree turn per second. If it is screwed in all at once, the timing belt tensioner adjuster rod will not easily retract and the tool may bend.

  8. Gradually screw in the special tool and then align the timing belt tensioner adjuster rod set hole “A” with the timing belt tensioner adjuster cylinder set hole “B”.
  9. Insert a wire or pin in the set holes to lock the assembly in place. After removing the special tool, loosen the timing belt tensioner pulley mounting bolts and remove the timing belt. If the belt is being reused be sure to mark the direction of rotation (clockwise) on the belt.
  10. Remove the timing belt tensioner pulley, tensioner arm and adjuster.
  11. Remove the timing belt idler pulley. Remove the timing belt lower cover bracket. Remove the crankshaft position sensor.
  12. Remove the crankshaft pulley center bolt and washer. Remove the drive sprocket. Remove the crankshaft angle sensing blade.
  13. Remove the balancer timing belt tensioner. Remove the timing belt “B” (balancer belt) from its mounting.


284eb62.gif
Timing belt tensioner adjuster rod set hole “A” and cylinder set hole “B”—2004–2005 Galant and 2004–2005 Lancer 2.4L engine

To install:


78b2d67.gif
Belt tension checking—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


b8fcecc.gif
Cylinder block plug location—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


bad1ef9.gif
Timing belt sprocket alignment—2002–2004–2005 Galant and 2004–2005 Lancer 2.4L engine

Feb 27, 2010 | 2004 Mitsubishi Galant

Not finding what you are looking for?
2005 Jeep Liberty Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...