Question about 1989 Ford Ranger

Open Question

Code p1444 1998 ford ranger

Ford ranger code p1444 diagnostics

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: I have a ford ranger and the diagnostic code

Ok.. The code P1400. Is. Related with the E.G.R system.
" Exaust Gas Recirculation"
The code P1400 is Exactly.
Sensor DPFEGR low voltage.
This code can set for.
Leaking up-strim pressure hose.
DPFEGR sensor Short to ground or signal return circuit.
VREF selenoid shorted to ground or signal return circuit.
Faulty DPFEGR .
or In the last case faulty PCM.

Ok.. The DPFEGR is a little box Located at the intake manifold.
to identificate See the Exaust Manifold Gasket you will see.
2 Little hoses Goin at the little box. When you found.
Check the hoses for cracked or damaged repair as need.
Check the connector.
The VREF. to locate follow the Little vaccum hose GREEN.
Goin to the EGR attached at the Intake manifold .
and check the connection.
If everything is OK. I recomend to replace the DPFEGR.

NOTE. If you don't have enought Expertise on vehicles.
I recomed to consult with your mechanic. and maybe give this information.
But if you can do your self go ahead.

I hope this help on your question. THANK YOU FOR USE FIXYA..

Posted on Dec 02, 2009

  • 67 Answers

SOURCE: how do I reset diagnostic

The easiest thing to try if you don't have a code reader that can erase codes is to remove both negative and positive battery terminals and hold them together for about a minute, this should drain all power from the battery and cause it to erase those trouble codes. If that doesn't work either buy a cheap code reader for $50-$100 that can erase codes.

Posted on Mar 27, 2011

  • 2006 Answers

SOURCE: diagnostic code for 96 ford

Evaporative Emission Control System Control Valve Which usually means the Canister Purge Assembly. This assembly connects the intake manifold to the charcoal canister and the assembly is made up of hoses, a valve and a sensor.

F57Z-9C987-AB Canister Purge Solenoid/Flow Sensor
Assembly - 2.3L F57Z-9C987-CA Canister Purge Solenoid/Flow Sensor
Assembly - 3.0L F57Z-9C87-BA Canister Purge Solenoid/Flow Sensor
Assembly - 4.0L

But double check for the right part number since my part catalog is for a 1997 and not a 1996.

Posted on Jun 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my ford ranger not shift automatically.it will shift fine if i start in first then second then drive but if i try to start in drive no go


Timothy, Open circuit in electrical system, failed PCM/TCM, faulty or stuck shift solenoid, failed speed sensor. Have checked for diagnostic codes to aide in diagnosing and a good transmission tech. give estimate on repair.
Solving Transmission Problems

Apr 22, 2016 | 1999 Ford Ranger SuperCab

1 Answer

Ive got a 93 ford ranger.after it gets warm & u cut it off for about 5 mins,& start it back its like it floods


Ford Check Engine light Codes - FreeAutoMechanic

www.freeautomechanic.com/diagnostictroblecodes7.html
Full list of OBD I Diagnostic Trouble Codes for your Ford Vehicle. If your Check engine light is on you may have a serious problem. Scan your codes and follow ...

EEC-IV 2 and 3 digit trouble codes. - Ford Explorer and Ranger ...

www.explorerforum.com > ... > EEC IV
Feb 6, 2007 - Serious Explorations Ford Explorer and Ranger Message Board .... 3.8L AXOD - Message center data link circuit fault - See code 70 73 (O) Is FORD DEALER the only place who can read out ABS error ...
Dec 5, 2011
Error codes 186 & 539.
Aug 15, 2009
OBD-II Diagnostic Trouble Codes (DTCs)
Nov 8, 2008
Have a Code? OBD II Trouble Codes Here
Jan 19, 2006
More results from www.explorerforum.com

EEC-IV Diagnostic Trouble Codes - Diagnose problems in


Dec 19, 2015 | 1988 Ford Ranger

1 Answer

Please help me 2013 ford ranger XLT giving problem trouble code po 366 air condition not working but when clear the code by diagnostic ac working after restart again I am facing same problem pls help me...


In my diagnostic book of codes p0366 refers to camshaft position sensor B bank 2 circuit range/performance unless there is a number missing in the code you quoted

Oct 31, 2013 | Cars & Trucks

1 Answer

FORD RANGER P0452 & P0453 DIAGNOSTIC CODES


Go here to look up these codes and the possible solutions to repairing them.

Feb 12, 2013 | Ford Cars & Trucks

1 Answer

On-Board Diagnostic II (OBD II) Diagnostic Link Connector (DLC) Location in 1999 ford Ranger


the ecc diagnostic plug is what ford used b 4 going to the obd 2 system check with ur local ford dealer for checking codes

Jan 08, 2013 | Cars & Trucks

1 Answer

Ford ranger airbag code 12


Code 12
Lost Battery Feed 9 (Dead battery or battery disconnected) The Airbag diagnostic module must be reset.
9_7_2012_10_32_25_pm.jpg9_7_2012_10_32_48_pm.jpg

Sep 06, 2012 | Ford Cars & Trucks

1 Answer

Need to know location for the fuse controlling the


disconnect the battery for 30 seconds, that will clear codes. if it comes back on then it isnt fixed

Jun 09, 2010 | 2004 Ford Ranger

1 Answer

2002 Ford Ranger check engine light indicating misfire


Code P0301
Ignition Coil Pack
Ignition Cable
Spark plug
Clog or dirty fuel injector
Evap canister purge valve
Engine Compression
fuel pressure

you have 3 type of engine for your truck
2.3L 4 cylinder
3.0L 6 Cylinder
4.0L 6 Cylinder

need to know that type Engine

The reason why the service light come on because it is a hard code
not a soft code.

Let me know

Sep 20, 2009 | 2002 Ford Ranger Regular Cab

1 Answer

O reading for O2 sensors on 98 Ranger XLT


Yes the 98 ranger has 3 02 sensors,they are located in the exhaust system under vehicle,2 of them
are in front of the cataletic converter and 1 behind it.I replaced mine ,reset the codes and the check
engine light still comes on?

Jan 16, 2009 | 2004 Ford Ranger

1 Answer

Diagnostic code


all the codes are here

quick guide part1 here
and part2 here

Jun 16, 2008 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...