Question about Cars & Trucks

Open Question

How to pull apart a 202 straight 6 holden motor

Posted by Anonymous on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 305 Answers

SOURCE: holden rodeo v6 1998 3.2L 4wd

the click is the solenoid hitting the bendix, try geting someone to turn the key,and as they do,tap the starter with a hammer, or heavy wrench, if it starts, then its the solenoid, and it can be stripped and replaced, if it doesnt start,then its the bendix, and you will need to replace the starter, ....which you can do yourself, .....takes about an hour or so

Posted on Jul 22, 2009

  • 220 Answers

SOURCE: location of engine number for holden 202 motor

Right engine mount side.

Posted on Oct 03, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Sump oil capacity holden 202 red moter

4.5 liters including oil filter

Feb 11, 2017 | Holden Cars & Trucks

1 Answer

Red 6 holden motor

you could if both engines have the same rear main seal, there was rope and neopreen rear main seals in blue motors
also would need to use same bearings as whats in the blue motor
marking on main bearings on the back eg STD, 010, 020
thats so you know what new main bearings you should then get & use, as well as the 2 thrust bearing peices
you should then check all clearance specs as you assemble crank into block with plasi gauge and your feeler gauges or the thrust bearings

Jan 26, 2014 | Holden Cars & Trucks

1 Answer

Can i fit a crank from a holden straight 6 red motor into a blue motor

measure the two cranks and if the bearings sizes match and the length is the same then it will only be the length of the stroke that will be a problem. Best way is to try it and see. Contact Holden car clubs as they will have members that will have tried this and will be able to give a better idea on the problems.

Jan 26, 2014 | Holden Cars & Trucks

1 Answer

I've got a 1999 VT commodore, have had injectors, plugs replaced but still have rough running in nuetral. Would it the plate where the leads plug into?

i just had this problem i had water coming into the motor via the inlet manifold . the only way is to pull it apart and look and replace $75 for Holden for inlet manifold gasket and they have to be done up by torque wrench to 8-12 nm or 6 fpound only or you crush them big job if you know how also clean throttle body


Mar 02, 2013 | 1998 Holden VT Commodore

1 Answer

Removing window motor

remove the door panel screws. there are 2. then remove the panel by pulling it straight back. start at 1 corner and work your way around. once loose, slide it off the door handle and unplug the window and door lock plugs and remove the panel. Pull the plastic back that is attached with a black urathine sealent from the lower left side and you will see the window moter. Unplug the motor. remove the motor spreding the 3 plastic clips apart and pull the motor straight back.

Feb 07, 2013 | 2000 Chevrolet Venture

1 Answer

What is the towing capacity of a Holden wb one tonner, with a 4 speed factory box and 202 motor ?

Check your owners manual on this, it is dependant on what towing gear the truck was ordered with from the dealer.

Jun 26, 2012 | Cars & Trucks

1 Answer

How do I remove the starter motor in my 1986 holden gemini RB. can only find one bolt

The other bolt is straight across from the one you pulled out you will need a 6 inch 3/8 drive extension and a wobble socket or a 3/8's swivel to get it out with. be sure to disconnect the positive battery cable at the battery before removing or trying to remove the opposite bolt or it will short and could cause the battery to explode. Rate if this was helpful. here is a picture of the starter so you can see it this is advance auto. 5841283_wrw_16884_thmb.jpg Worldwide Starter Part No. 16884
Reman; with Automatic Transmission; See Test Chart Page # S-4
Core Charge $10.00 ?

Sep 21, 2009 | 1986 Isuzu I-Mark

4 Answers

Torque wrench settings

please understand there are a lot of items on a car that require torque settings every thing from the lug nuts to every engine bolt, and transbolt. please be more specific

Jul 03, 2008 | 1999 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides