Question about 1993 Jeep Cherokee Country

1 Answer

Slave cinlinder where can i find diagrams showing my transmission and slave cinlinder.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 409 Answers

Http:// go to thi site.

Posted on Jan 02, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I just replaced my master clutch cylinderin my 2008 lancer a week ago,paid 400. Now they're saying its the slave cylinder and they have to pull the transmission out and get deep into it and...

You could have either an internal [concentric] clutch slave cylinder or an external slave cylinder depending on which transmission Mitsubishi used for your car. The problem is that automobile manufacturers all source parts from wherever they can and from each other.
The video shows an external and easy [relatively inexpensive to replace slave cylinder. An external slave cylinder shouldn't cost more than $40 in parts and less than one hour of labor to replace. A look under your car may save you lots of money. Also look for a reliable independent repair shop rather than the dealer to save money.
Then there is the centric slave cylinder that fits around the transmission input shaft [requiring transmission removal to replace].
If you have this type of slave cylinder, you are in for close to $100 in parts and 5 to 6 hours of labor.

Jan 31, 2015 | Cars & Trucks

1 Answer

Is the slave cylinder inside the transmission

The clutch slave cylinder is at the throwout bearing. Inside the transmission makes no sense

Aug 14, 2014 | Pontiac Sunfire Cars & Trucks

1 Answer

Finding a clutch slave cylinder on a 2005 ford focus

the slave cylinder is mounted inside the bell housing on the transmission, You will have to pull the transmission to replace. here is a diagram.


Aug 03, 2012 | 2005 Ford Focus

1 Answer

Do i have to drop the transmission to fix the leak on the slave cylindar

The Clutch Slave Cylinder is leaking on your car. The slave cylinder and the clutch release bearing are all one assembly (see picture below), so you must remove the transmission to replace the clutch Salve cylinder. All late model GM cars are this design.

Jan 26, 2012 | Pontiac GTO Cars & Trucks

2 Answers

Where is the 1999 Saturn SL2 slave cylinder located?

on a manual transmission the Clutch Slave Cylinder is located on the drivers side front of the transmission. You can locate it by first finding the clutch master cylinder on the drivers side of the firewall. Then fallow the plastic line to the front of the transmission.

To remove the slave you will first twist it then pull it out of the transmission.

The clutch slave and mater cylinder are replaced as an assembly.

Oct 07, 2011 | 1999 Saturn SL

2 Answers

Slave cylinder leaks

Remove the bolts holding the slave cylinder to the transmission. Disconnect the hydraulic hose. Reconnect hydraulic hose to new slave cylinder, and install the slave cylinder in it's original position.

Now proceed to bleed the line through the slave cylinder until a solid stream of fluid comes through, and the pedal pressure becomes firm.

Jul 10, 2010 | 1991 Jeep Wrangler

1 Answer

How do I change the slave cylinder on a 1999 mercury cougar? I'm 99.9% sure this is my problem but I don't know how to get to it. I've heard it can be down without having to drop the whole transmission but...

There;s no two way's about it you'll have to remove transmission, put car up on jack stand's, then remove driver shaft, remove linkage or stick shift and all elec. connection, remove line going to slave cylinder( you'll need a line disconnect tool napa has it part # 775-9086), remove starter assembly, remove all bolts around trans bell housing, pull trans away from engine, slave cylinder slide on input shaft of trans, remove slave 10mm bolt's and replace slave. after all reassemble bleed clutch system

Dec 07, 2009 | 1999 Mercury Cougar

1 Answer

Is there a diagram showing the location of the slave cylinder on a 1986 jeep cherokee / 2.5I4?

Follow the line from the clutch master to the slave. Its within a 3 foot distance.

Nov 06, 2009 | 1986 Jeep Cherokee

1 Answer

Need to replace slave cylinder clutch goes to floor without any pressure. Does the transmissin have to be taken out

Transmission stays in. Buy a Haynes manual for your model and it shows how to replace slave cylinder.

Sep 08, 2009 | 2002 Saturn VUE

1 Answer

Hydraulic clutch slave cylinder leaks needs replacement

you sure can replace it. I suggest checking out for a free online repair manual with step by step directions and diagrams

Mar 31, 2009 | 1986 Ford F 250

Not finding what you are looking for?
1993 Jeep Cherokee Country Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides