Question about 1996 Dodge Intrepid

1 Answer

I think my pcv valve needs changing. Car seems to be missing, changed plugs. don't know where PCV valve is located on engine.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

It will be mounted with a rubber gromet on one of the valve covers

Robert

Posted on Jan 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Trying to replace PCV valve on 4.6 L 2001 Crown Vic. Believe it is located on valve cover on driver side, but not positive. I tied to pull it out to replace and it was so stuck I was afraid to use pliers...


PCV valves are usualy in the valve cover like you say. they only need to be changed if they quit working. If you pull it out of the gromet it is pushed into, just shake it. If the check valve inside makes noise then the valve is good. In 35+ yrs of working on cars I haven't seen a PCV valve fail. Here is a picture of it so you know what your looking at:

chuckster57_46.jpg

Jun 11, 2011 | Ford Crown Victoria Cars & Trucks

1 Answer

Were is the pcv valve on a 2005 ford freestar


pcv valve is located on the valve cover of the engine. you will see a line running close to the middle of the valve cover gently pull the line out of the valve cover, the pcv valve will be on the end of the line. take out the pcv shake it, if it rattles it is okay, if you don`t hear a rattle it needs to be replaced. Also I personally would change the pcv valve every 25,000 to 30,000 miles because they are usually inexpensive.

Feb 12, 2011 | 2005 Ford Freestar

1 Answer

04 jeep grand cherokee 4.7 v8. I changed 7 spark plugs with ngk plugs could not get to the 8th passenger side firewall plug. engine seems to missfire upon startup for 30 seconds or less then runs smooth...


Change the pcv valve this will cause problems. You can get the eighth plug, put the socket on the plug and use a wrench that fits the socket to get it loose or out. It's a pain but necessary.
Randy

Nov 10, 2010 | 2004 Jeep Grand Cherokee

2 Answers

MY SUZUKI GET TOO MUCH WHITE SMOKE,BUT I HAVE PUT ENGIN FLUSH, CHANGE THE OIL AND THE OIL FILTER,ADD ANTISMOKE TO FUEL BUT NO CHANGES PLEASE!!!


There has been an issue of Suzuki engines smoking due to the PCV. valve or the baffles under the valve cover. One method of curing this is to place an oil separator between the vacuum line from the intake and the PCV. This will make for the need to keep an eye on it as it will fill up with oil eventually thus negating the purpose of placing it there in the first place. I think the big fix would be to remove the valve cover and check the oil baffles and filter therein. The problem is that oil builds up at the location of the PCV and is getting sucked into the intake via the vacuum hose to the intake. The quick fix? unplug the PCV and plug up the vacuum hose to the intake. This will get you by until you can get it to a mechanic. Anyway, That what I know. hope it helps

Aug 23, 2010 | 1999 Suzuki Grand Vitara

3 Answers

2003 ford taurus idle problems had trouble codes


A code P0174 may mean that one or more of the following has happened:
  • The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filters can cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.
  • There could be a vacuum leak downstream of the MAF sensor. and your solutions are.
    • In the vast majority of cases, simply cleaning the MAF sensor does the trick. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner . Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstalling
    • Inspect all vacuum and PCV hoses, replace if necessary
    • Check for a dirty fuel filter and proper fuel pressure

Oct 24, 2009 | 2003 Ford Taurus

4 Answers

How to replace a PCV valve on my 1997 dodge neon? I travel over 60 miles a day and when at stop lights i have a light rough idle. Just replaced the plugs and wires 15k miles ago and the air filter 500...


Once you have the new PCV valve locate the old one on your engine. It will sit on the middle of one of your valve covers (most likely passenger side) and will have a line that connects to the top of the valve. Simply pull the old one out and put the new one in snapping that line on the new one. Should only take about a minute to do. Hope this helps, let me know if it does.

May 05, 2009 | 1998 Dodge Neon

1 Answer

Location for pcv valve on 2002 Toyota Camry 4cyl


Daeler Mechanic told me there is no PCV valve on my particular model.

Apr 08, 2009 | 2002 Toyota Camry

1 Answer

Where is the pcv valve located on a 2000 zetec engine?


try Google.com [2000 focus pcv valve] somebody should show you where it is.good luck, John

Nov 02, 2008 | 2000 Ford Focus

2 Answers

PCV valve location


if i know what you are asking, look at where you put your oil in. on the valve cover to the top right should be a plug with a tubeing runs to your air clear tube where the air mass sensor and carb is located. i think that is what you are looking for.

Sep 05, 2008 | 2002 Ford Taurus

Not finding what you are looking for?
1996 Dodge Intrepid Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...