Question about 1994 Oldsmobile Achieva Special Edition

1 Answer

Rear lights don't work nor license plate light

The turn signal and the brake lights work but the rear lights don't come on when the headlights are on.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 25 Answers

Start with checking or replacing the bulbs, if you had an electrical problem, nothing would be lighting up in the back.

Let me know, Pierre ( Montreal)

Posted on Jan 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My license plate lights are not working. I have voltage at the trunk light (11.48 VDC), but not from the two license plate sockets when I turn the headlights on. I uncliped and removed the sockets in order...


could have poor ground wire use 12 volt test light check probe socket positive wire could be grey green wires and touch ground if test light works you have bad ground to license plate lights.and license plates lights have fuse control circuit.

Oct 22, 2013 | 2001 Jaguar S-Type

1 Answer

1995 saab 900 convertible turn signals and brake lights not working


Check your fuses, even fuses not associated with lighting. If all ok it is probably the muti-funtion switch on the steering column, It is the switch that your turn signal lever connects to.

Oct 03, 2012 | 1995 Saab 900

1 Answer

I have a 1999 gmc suburban 4x4. All rear lights and license plate lights are not working. All fuses are good as well as all light bulbs. Any ideas what the problem could be?


Sounds like a faulty signal switch.Here's a way to check it,hold the brake pedal down while pushing down on and wiggling the hazard switch.If the brake lights come then replace the signal switch.

Apr 30, 2012 | Nissan Sentra Cars & Trucks

1 Answer

Fuses panel described in English


Hope this helps your out. I know the diagram and locator is a bit blurry but hopefully it gets what you need.
Drivers kick panel:
Front wiper 20A - Front wiper system Cigar 15A- Cigarette lighter Audio 10A- Audio, remote control mirror Air Bag 10A -Air bag diagnostics Stop lights- 15A -Rear brake light, high mounted stop light ECU B+ 10A - Shift lock actuator, transaxle controle module, radio, engine control module Room 10A - Interior light, clock, ignition key reminder, rear cargo area light switch ABS 10A- Anti lock brake system control unit ECU IG1 10A - Transaxle control module, shift lock actuator, ABS control unit, DRL unit Meter 10A - Instrument panel, back-up switch, electronics time control module, inhibit switch Turn signal 10A- Hazard switch ,front and rear turn lights, turn indicator IGN1 20A - Ignition switch ABS 30A- ABS pump motor TNS 30A- Tail light, license plate light COOL/FAN 30A- Cooling fan Cond/Fan 20A- A/C condenser fan Starter 15A- Start signal , Fuel pump Blower 25A- Blower Motor SR/ACC 10A - Ignition switch Hazard 15A - Hazard and turn signal light D/Lock 25A- Door locks ABS 30A - Anti lock brake system control P/W RH 20A- Power window motor right hand P/W LH 20A- Power window motor left hand IGN2 25A- Ignition Switch
Engine compartment :
Head 25A- headlights IG 2 30A- Ignition switch IG coil 15A -Ignition coil, condenser,generator IC regulator, diagnostic connector. O2 down 10A- Rear O2 sensor O2 up 10A- Front O2 sensor Fuel pump 10A -Fuel pump unit Injector 10A -Fuel injector ,camshaft positioning sensor, purge solenoid valve, EVAP, IAC actuator, Mass Airflow sensor, EGR stepper motor. fuel pump relay coil, vehicle speed sensor. A/Con 10A - A/C compressor controls, cooling fan BTN 30A- Brake light , high mounted stop light. Tail light LH 10A- License plate light, tail light , rear combo light, instrument panel illumination Tail light RH 10A-License plate light, tail light , rear combo light, instrument panel illumination Head low 15A- Headlight Head Hi 15A-Headlight Horn 15A- Horn jlmacman.png jlmacman_0.png

Inside kick panel jlmacman_1.png

Mar 07, 2011 | 1995 Kia Sephia

1 Answer

My license plate lights are out...what kind of bulbs do i need??


Check this reference guide...

2002 Hyundai Accent Car Lightbulb Size Guide
Low Beam Headlight Bulb Size: 9003/HB2
High Beam Headlamp Light Bulb Size: 9003/HB2
Parking Light Bulb Size: 2357A
Front Turn Signal Light Bulb Size: 2357A
Rear Turn Signal Light Bulb Size: 1156
Tail Light Bulb Size: 1157
Stop Light Bulb Size: 1157
High Mount Stop Light Bulb Size: 921
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 1156
Front Side Marker Light Bulb Size: 2357A
Rear Sidemarker Light Bulb Size: 168
Map Light Bulb Size: DE3175
Dome Light Bulb Size: DE3175
Step/Courtesy Light Bulb Size: DE3022
Trunk/Cargo Area Light Bulb Size: DE3022

From Sylvania Lamp Replacement Guide
License plate
168
168LL Long Life Upgrade: Up to twice the life of the standard lamp.


I hope help you with this. Good luck (remember rated this help).


Sep 09, 2009 | 2002 Hyundai Accent

1 Answer

1965 ford mustang...rear turn signals, rear emerg flashers & brake lights not working.


Are the rear bulbs OK?
Is the ground good at the rear?are the sockets good?
Are there tail lights and a license plate light?then the ground is OK.
All the things that you say do not work go through the signal light switch....it may need replacing.
First make sure the bulbs and fuses are OK and power is getting to the signal light switch and to the brake light switch.
Nice car!

Aug 31, 2009 | 1965 Ford Mustang

1 Answer

How do i change rear turn signal bulb on 89 corvette, notmine???


Rear Turn Signal, Brake and Parking Lights 1984–89 VEHICLES
  1. If removing an inner bulb, remove the license plate. For outer bulb replacement, reach from under the vehicle.
  2. To remove the inner rear brake light, you must reach behind the license place and under the vehicle to access the bulb and socket
  3. Remove the socket from the lens by releasing the locking tab and twisting
  4. Once the bulb and socket are pulled from the rear of the lens, grasp it from behind the license plate opening
  5. Then, pull it out of the side and replace the bulb
  6. Remove the bulb from the socket and replace.
  7. Installation is the reverse of the removal procedure.

Apr 05, 2009 | 1989 Chevrolet Corvette

1 Answer

1993 Toyota Camry - Tail lights don't work / brake lights do?


Dude the wires at the trunk inside break from opening and closing. you must peel back the wires covering to expose and fix these wires.

Mar 24, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
1994 Oldsmobile Achieva Special Edition Logo

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...