Question about 1999 Chrysler Town & Country

1 Answer

Where is the Body Control Module located?

1999 Chrysler Town & Country - Limited

Posted by on

  • 1 more comment 
  • Anonymous Mar 20, 2014

    head light out I was told I needed a front control module and now a brake light is out can it be related

  • Anonymous Mar 21, 2014

    location of the tcm and the ecm 2007 chrysler 300

  • Anonymous Mar 29, 2014

    Can you tell me where it is located

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 152 Answers

It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the bcm.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the bcm to the jb. Slide the bcm downward to disengage guide studs on jb from channels on bcm mounting bracket
Remove bcm from jb.

Posted on Jan 02, 2009

  • reknon Jan 30, 2011

    Very important!!...there are three screws holding the bcm to the jb. You'll see the first two on one side of the bcm in plain sight. The third screw is hiding way up on the opposite side towards the back of the bcm. If you look up the length of the bcm from the "two plugs" end towards the rear of the bcm, you should see it. You may need to lie on your back with a flashlight and look up to even see it and will need a longer screw driver. This third screw eluded me and caused me to eventually "rip" the bcm out and off the junction block.

×

1 Suggested Answer

emissionwiz
  • 60867 Answers

SOURCE: where is the body control module located on a 1997 town & country

It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the BCM.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the BCM to the junction block. Slide the BCM downward to disengage guide studs on jb from channels on BCM mounting bracket

Posted on Mar 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Blinkers don't work at all. Where can I find the fuse or relay? I'm very frustrated. I need help.


Chris, fuse could be down under the dash to the left kind of near where your left knee would be when you are driving or under hood (engine compartment) in the fuse/relay center.
It could also be faulty flasher, wiring, etc
I will post some trouble shooting links for you.
Press the helpful button.
1996 2000 Chrysler Town and Country Interior Fuse Check 2000 Chrysler Town...

How To Install Replace Taillight and Bulb Chrysler Town Country 04 07...

Fuse Box Location in 1999 Plymouth Grand Voyager Van

Quick Tip Signs of blown IOD Fuse on Chrysler Dodge Jeep Fiat or Ram...


Feb 15, 2016 | 2002 Chrysler Town & Country

1 Answer

Where is the location of xenon control module on a 2006 chrysler 300c


Part of the integrated power module includes the front control module. Low beam driver output from the module closes the high intensity discharge lamp relay contacts and, if 50A FUSE 23 is OK, applies power through 20A FUSE 1 to the left high intensity discharge lamp and through 20A FUSE 2 to the right high intensity discharge lamp.

May 18, 2014 | 1999 Chrysler Town & Country

1 Answer

Body control module location 99


UNDER DRIVERS SIDE FRONT DASH LEFT OF STEERING COLUMN

Jan 01, 2014 | 1999 Chrysler Town & Country

2 Answers

1999 Chrysler T&C Limited - Driving lights/Fog Lights


The fuses that protect your headlamp circuits are Fuse Numbers [4] (Left High Beam), [5] (Right High Beam) [6] (Left Low Beam) and [7] (Right Low Beam).
Fuse 4 is a 10 Amp fuse
Fuse 5 is a 10 Amp fuse
Fuse 6 is a 20 Amp fuse
Fuse 7 is a 15 Amp fuse
All are located in the Power Distribution Center in the engine compartment.

The difference between a 1999 Chrysler Town & Country with DRL and WITHOUT DRL is that one has a DRL module and the other does not. The headlmps themselves are wired exactly the same.

To make yours work, you would have to add the DRL module and reprogram your Body Control Module (BCM) to accept the DRL module. Doing it any other way would probably result in the BCM setting fault codes and possibly even causing malfunctions in other non-headlamp-related circuits.

Apr 22, 2012 | 1999 Chrysler Town & Country

1 Answer

I lose power to the door locks on my and car wont start 1999 chrysler town county


possible cause would be broken door wires in the harness between the door and the body on the driver side , also another problem could be the bcm ( body control module ) some times these can be flashed or reprogramed at the dealer with new software .

Apr 09, 2010 | 2001 Chrysler Town & Country

3 Answers

The power locks have stopped working, what can do to fix it?


I had the same problem with my 2005 Town & Country Limited, and the dealer didn't have a clue what was causing it. After doing some research, I found the fuse (20 amp) that's associated with the door locks and unplugged it for about 10 seconds, and then plugged it back in. The fuse was not bad, but seamed to reset the system. Give it a try. It's simple and free. Good luck.

Mar 19, 2010 | 2005 Chrysler Town & Country

1 Answer

I have a 2002 town & Country and think the BCM is bad


Check all fuses under dash & under hood in fuse/relay box first.

Jun 24, 2009 | 1999 Chrysler Town & Country

1 Answer

Where is the body control module located on a 1997 town & country


It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the BCM.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the BCM to the junction block. Slide the BCM downward to disengage guide studs on jb from channels on BCM mounting bracket

Mar 23, 2009 | 1999 Chrysler Town & Country

Not finding what you are looking for?
1999 Chrysler Town & Country Logo

6,430 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...