Question about 2000 Ford Ranger SuperCab

1 Answer

I have a 2000 ford ranger xlt 4x4 w/ 4.0 engine.when i try to engage the 4 wheel drive the 4 wheel low and 4 wheel high light blinks back and forth for a couple of seconds.also it sounds like some kind of clicking noise coming from the switch.but it wont go into low or high. thanks for any help you can give. Thus problem started all at once before that 4x4 worked fine. Anything would be helpful Thanks- Kevin-

Posted by on

  • Anonymous Feb 22, 2009

    My 2000 Ford Ranger 3.0 Manual Trans will go into 4x4 high but not 4x4 low. It has had a problem in the past, returning to 4x4 high after being in 4x4 low. Now it will not go into 4x4 low. Any help will be appreciated. Thanks, Gary

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

You pretty much answered yourself here, the switch sounds like it is going bad.

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4x4 will shift to 4 high but will not go to 4 low


Ford Ranger Questions - 4 wheel drive relay clicking under ...

www.cargurus.com > Questions > Ford > Ranger
CarGurusJun 5, 2013 - 4 wheel drive relay clicking under dash - i put my truch in 4x4 the other day and ... and watch it move (or not move) while selecting 4x4 high, low and so forth.... MY 1999 Ford Ranger 4x4 will not go in 4 wheel drive 5 answers.

Sep 14, 2015 | 1999 Ford Ranger SuperCab

1 Answer

99 4.0 super cab ranger 4x4 xlt, 4wd high & low light flashing on console, won't engage .


check the rods are not bent at transfer case try putting it into gear with a shifter from underneath ,if no go must be internal also try backing up if possible.

Aug 26, 2014 | Ford Ranger Cars & Trucks

1 Answer

Will not go in 4 low 4x4 lights start blinking after trying . reset light by unhooking battery . then goes in 4 high normelly but not 4 low. i thlnk auto 4 is working 4 liter SOHC 1998


Normally 4 wheel drive HIGH is engaged on the fly or as you are moving more than 10 km per hour or 10 miles per hour but 4 wheel drive LOW is engaged at around 3 to 5 mph. no more or you could ruin the transfer case. Try going from 2 high to 4 high by switching back and forth and then try 2 high to 4 low when idling along. What usually happens is the mechanics under the car freeze up or rust up and you have to switch back and forth to free it up.

Nov 01, 2010 | 1998 Ford Explorer

3 Answers

Wont disengage out of 4 wheel drive 1998 ford ranger first time its stuck in 4 low we have backed up turned switch numerous times shut it off and restarted


Be sure to put the truck in neutral, while engine is running, while you disengage from 4 wheel drive (low) to 4 wheel drive (high) and then finally to 2 wheel drive. It is critical to shift transmission into neutral when switching out of 4WD Low, as indicated in your owner's manual. Hopefully, this will help to FixYa problem!

Oct 14, 2010 | 1998 Ford Ranger SuperCab

3 Answers

2000 Ford Ranger XLT electrical problem


Check your rear end to see if you have a sensor like in this video, if so it could solve some issues. The video describes items all going out around the same time. Its based on a 2 wheel drive but who knows you might have the same sensor in the same location. This is a shot in the dark, but who knows it might help or point you in the right direction.

Nov 04, 2009 | 2000 Ford Ranger SuperCab

1 Answer

2000 Ford Ranger XLT Automatic trans. 4X4 3.0L


Check your operator's manual. Make sure any and all fuses that have anything to do with the affected items are not blown and are working properly. If you can; check for loose fuse connections or wires. Hope this helps. God bless!

Nov 04, 2009 | 2000 Ford Ranger SuperCab

1 Answer

PUSH BUTTON FOUR WHEEL DRIVE FORD RANGER NOT WORKING


the transfer case is sticking from non use, change the lube in the case ( Ford ATF) and drive it for awhile it should be ok then.

Apr 07, 2009 | 1988 Ford Ranger

1 Answer

4x4 will not engage,lights just blink,and you can here clicking


The 4x4 system has a controller,or computer,called the Body Control Module and there will be stored trouble codes.To work on a system that's electronically controlled,you have to get the codes from the system.Every trouble code has a diagnostic route to follow to resolve the faulty component.I have read about Explorers having faulty door open/closed sensors.These set a code in the Body Control Module,and in the process,the BCM inhibits 4x4 operation,causing a no 4 wheel drive complaint.There is also an electric motor on the transfer case that can fail electrically or mechanically,along with speed sensors and fork position sensors that can give trouble.

Sep 02, 2008 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
2000 Ford Ranger SuperCab Logo

473 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...