Question about 1991 Dodge Ram

2 Answers

How do I bleed the injectors on my 5.9 litre cummins. I have the fuel pump and filter replace and still not getting fire in the engine

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Crack each fuel rail line in the firing order which should be 152436 crank for 1-3 seconds on each or till fuel comes out. the easiest thing to do is change primary and secondary fuel filters

Posted on Feb 06, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 77 Answers

CHECK YOUR GLOW PLUGS, THEY WORK LIKE A SPARK BY WARMING SYSTEM FOR FIRING.

Posted on Jan 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you bleed a diesel pump jeep Cherokee turbo diesel 3.1 5 cylinder 2001


we dont have this engine here, USA.
but i have the WG jeep book,
starting page 12 , chapter 14


FUEL INJECTION PUMP BLEEDING
(1) If the fuel injection pump has been replaced,
air should be bled at the overflow valve before
attempting to start engine.
(a) Loosen the overflow valve (Fig. 18) at the
rear of the injection pump.
(b) Place a towel below the valve.
WARNING: WHEN CRANKING THE ENGINE TO
BLEED AIR FROM THE INJECTION PUMP, THE
ENGINE MAY START. PLACE THE TRANSMISSION
IN NEUTRAL OR PARK AND SET PARKING BRAKE
BEFORE ENGAGING THE STARTER MOTOR.
CAUTION: Do not engage the starter motor for
more than 30 seconds at a time. Allow 2 minutes
between cranking intervals.
(2) Crank the engine for 30 seconds at a time to
allow air trapped in the injection pump to vent out
the fuel injector drain tubes. Continue this procedure
until the engine starts. Observe the previous WARNING
and CAUTION.
(3) Tighten overflow valve.
HIGH-PRESSURE FUEL LINE BLEEDING
WARNING: THE INJECTION PUMP SUPPLIES HIGH-
-PRESSURE FUEL OF APPROXIMATELY 45,000 KPA
(6,526 PSI) TO EACH INDIVIDUAL INJECTOR
THROUGH THE HIGH-PRESSURE LINES. FUEL
UNDER THIS AMOUNT OF PRESSURE CAN PENETRATE
THE SKIN AND CAUSE PERSONAL INJURY.
WEAR SAFETY GOGGLES AND ADEQUATE PROTECTIVE
CLOTHING AND AVOID CONTACT WITH
FUEL SPRAY WHEN BLEEDING HIGH-PRESSURE
FUEL LINES.
WARNING: DO NOT BLEED AIR FROM THE FUEL
SYSTEM OF A HOT ENGINE. DO NOT ALLOW FUEL
TO SPRAY ONTO THE EXHAUST MANIFOLD WHEN
BLEEDING AIR FROM THE FUEL SYSTEM.
Bleed air from one injector at time.
(1) Loosen the high-pressure fuel line fitting at
the injector (Fig. 19).
(2) Crank the engine until all air has been bled
from the line. Do not operate the starter motor
for longer than 30 seconds. Wait 2 minutes
between cranking intervals.
(3) Start the engine and bleed one injector at a
time until the engine runs smoothly.

end quote.
pump timing is on next page
or tank filter line priming before. above.

Mar 22, 2016 | Jeep Cars & Trucks

1 Answer

How to bleed a diesel bus engine


there will be a small hand pump either on the diesel pump or on the filter. bleed the filter out first and then open the bleed screws on the pump and pump until you get straight fuel., The pump may requiring unscrewing the handle/knob first so that you can move it up and down to pump. When finished remember to re screw it back down. crack the injector lines and turn engine over until you get drips of fuel from the nuts. continue to turn over the engine while tightening the nuts and it should start before you have finished with the nuts.

Nov 10, 2013 | Cars & Trucks

2 Answers

My 5.9 dodge cummins diesel won't start, I've replaced the fuel lift pump, and the fuel filter, turns over. But will not start?


Most likely you just have air in the lines.Crack them open one at a time and bleed them with the fuel pump off and on till you get fuel.If it fires dont hit the throttle let it sit and idle and close the line.Does it fire up with a small whif of starting fluid?

Mar 17, 2013 | 1999 Dodge Ram

2 Answers

I ran a mixture of diesel and water thru my fuel system about three miles or so what do i do now


drain the fuel, change the filter, add fresh diesel. cycle the key several times and see if she fires up. you might have to crack the injector lines to help in bleeding the air out of the system. the good thing is the vp44 injection pump doesn't know what its pumping and 2001 24v cummins do not have electronic injectors, so you should be ok.

Mar 03, 2013 | 2001 Dodge Ram 2500 Truck

2 Answers

My golf 1.9 tdi is miss-firing


Check the fuel lines, fuel filter, what is the mileage? If it is high than it might a sign of injector pump or injectors.

Apr 08, 2010 | 2002 Volkswagen Golf

3 Answers

2001 Dodge Ram 2500 HO Cummins 6 Speed


TAKE IT TO A MECHANIC !!!!!!!!!!!!!!

May 31, 2009 | 2001 Dodge Ram 2500 Truck

5 Answers

Dodge cummins won't start, fuel reaching injector pump but no fuel coming out of injector pump.


You said you have fuel flowing from the inlet line of the injection pump? But not at the injector lines?

May 05, 2009 | 1999 Dodge Ram

2 Answers

WONT START


to dogy2003: 1995 Dodge Ram 2500's with Cummins Turbo Diesel do not have glow plugs

I agree with kious75, you need to get the air out of the injector lines. Has the truck ran AT ALL since the installation of the injector pump?

What type of additive did you put in the trucks fuel tank?

Have you replaced the fuel filter recently? Check the filter canister to see if fuel has been pumped in to it. (one way to check is to open the water/fuel seperator valve on the bottom of the fuel filter canister and see if there is any fuel or water in there)

I had a 1999 Dodge Ram 2500 with a 24V Cummins ISB engine and had trouble getting it to start. Had NO luck bleeding the injector lines. My truck was a 5-speed so I got it on dry level ground and had a friend pull me with his truck, I popped the clutch in 3rd gear and the truck cranked up beautifully. It is similar to the process you would go thru if you had an old 5-speed vehicle with a dead battery. The engine and fuel delivery system on my truck and your truck are different but similar. My problem was a bad "lift pump" which was about $150 to fix, but caused a $1500 injector pump failure. I was nervous about pull starting my truck but it worked... the truck always cranked up after that.

Jan 29, 2009 | 1995 Dodge Ram 2500

3 Answers

Truck wont start after draining fuel filter?


You may have gotten air in the fuel lines. Diesels cant deal with this as well as gas engines should be a purge / bleeder valve on the fuel lines to eliminate the air. may cough and sputter for a while

Jan 24, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...