Question about 2002 Chrysler Sebring

1 Answer

98 sebring lxi

My 98 sebring lxi when i trun left of right the flasher works fine but when driving the flasher will not stop ticking as if i had a brunt out lightbut goes normal when i make the trun can you help me

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

This may have something to do with the 4 way flasher fuse. Do a check of your 4 ways and if needed change out the fuse. back square fuse in most cars
Check you steering aswell turn the wheel to where the signal stops chicking see if there is a point to where it will stop

Posted on Jan 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I get a constant clinking from turn signal flasher when I am not using the left,right or 4-way switch


constant clinking James, change the flasher may fix the problem, if not the problem could be in the multi switch itself.

Mar 30, 2016 | 1999 Chrysler Sebring LXi

1 Answer

LXI. how do I replace flasher?


The Flasher is located: Behind A/C and heater control panel, in center console.

Flashers

Print
REPLACEMENT

Flashers are located either on the bottom of the fuse block or on a module under the dashboard. They are replaced by simply pulling them straight out. Note that the prongs are arranged in such a way that the flasher must be properly oriented before attempting to install it. Turn the flasher until the orientation of the prongs is correct and simply push it firmly in until the prongs are fully engaged.clink on link to see what flasher look's like.
http://www.autozone.com/electrical-and-lighting/turn-signal-flasher/novita-turn-signal-flasher/chrysler/sebring/1998/4-cylinders-y-2-0l-mfi-dohc/193143_0_7283

Aug 15, 2015 | 1997 Chrysler Sebring

1 Answer

1998 crysler sebring lxi repair manual


98 cry sebring lxi trying to find the coil on the car?

Oct 06, 2010 | Chrysler Sebring Cars & Trucks

2 Answers

98 Sebring JXI turn signals work right/left and


Change the flasher which is located up by fuse block under dash

Jul 29, 2009 | Chrysler Sebring Cars & Trucks

1 Answer

98 lumina brake lights and rear turn signals stopped working.


A flasher would not cause this problem, It's in the trun signal switch, it needs to be replaced

May 30, 2009 | 1997 Chevrolet Lumina

3 Answers

Blinker stopped working, but the hazard lights still work - I think it's a blown fuse but how and where do I fix the fuse


There is 2 different flashers. One flasher for the turn signals and one flasher for the hazards. If you turn on the turn signals and the turn indicator on the dash lights up but doesn't blink, then most likely it is the turn signal flasher that is bad. Good luck.

May 29, 2009 | 1998 Chrysler Sebring

1 Answer

1999 Nissan Altima GXE Turn signal problem


you have a busted bulb, your hazard may be working fine but the bulb is double contact so one part is working and the other is not. just check which bulb is busted.

Apr 20, 2009 | 1999 Nissan Altima

2 Answers

Replacing headlight bulbs on a 2006 chrysler sebring


Behind the headlight you should see a eletrical wires running to the headlight section. There will be a 2 inch round plastic ring. You grap the back of the bulb and turn it to the right which will release the bulb and the socket. You pull out the bulb and replace it the same way. If this doesnt help then get back to me.

Feb 06, 2009 | 2006 Chrysler Sebring

3 Answers

Blinkers stopped working


Your F--150 has 2 flashers, emergency and turn signal. Both are mounted on the fuse block under the dash. The turn signal flasher is mounted on the front of the fuse panel, the emergency flasher is mounted on the rear of the fuse panel. so replace the turn signal flasher should solve the problem. Let me know how it goes.

Oct 20, 2008 | 1996 Ford F150 Regular Cab

Not finding what you are looking for?
2002 Chrysler Sebring Logo

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...