Question about 2006 Volkswagen GTI

1 Answer

06 polo headlamp (whole unit) bracket broken..???

Front left headlamp unit bracket on top is broken can it be repaired or do I have to change whole unit and how do i do it??

Posted by on

  • bigjas1uk Jan 04, 2009

    I havent done it yet and the entire unit is loose, so that tells me the only thing holding it in place is the 1 bracket on top, if it were bolted from below it wouldnt be loose....?



×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 345 Answers

Whole unit,remove front bumper to get to bottom bolts

Posted on Jan 02, 2009

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the headlight housing on my 1999 lumina


Raise the hood.
Lift the flap on the appropriate end of the radiator upper air deflector.
Separate the radiator side air baffle from the upper air deflector.
Remove the fastener retaining the upper edge of the front bumper fascia to the headlamp bracket.
Remove the two bolts retaining the headlamp assembly to the headlamp bracket.
Slide the headlamp assembly slightly inboard to release the outboard retaining tabs. Carefully pull the upper edge of the front bumper fascia away from the inboard edge of the headlamp assembly enough to aid in headlamp removal. Carefully remove the headlamp assembly from headlamp bracket.

Nov 22, 2014 | 1999 Chevrolet Lumina

1 Answer

How to replace polo 2011 headlights


hi. you need to remove the front bumper to accses the headlamps

Jan 08, 2014 | 2012 Volkswagen Polo

1 Answer

06 Cadillac CTS...driver side headlamp washer appears to be broken. Can I replace just the washer, or do I have to replace the entire assembly?


You will have to call a parts store in your area and ask them. Here in Texas you have to replace the whole unit. Thats if you dont want to goto a junk yard.

Mar 07, 2011 | 2006 Cadillac CTS

1 Answer

How do you change the headlamp on a 2008 mailbu?


dcramer531_8.gif Remove the front bumper fascia upper bracket. Refer to Front Bumper Fascia Bracket Replacement .
1
Headlamp Screw (Qty: 2)
Notice: Refer to Fastener Notice in the Preface section.
Tip
Secure the headlamp fasteners in sequence, as indicated.
Tighten
3 N·m (27 lb in)
2
Headlamp Assembly
Procedure
  1. <LI type=1>Pull forward on the outside edge of the headlamp in order to release the up and down locator tabs on the backside of the headlamp. <LI type=1>Pull forward on the top inside edge of the headlamp to release the inboard up/down locator. <LI type=1>Pull the headlamp assembly down. <LI type=1>Pull the headlamp assembly forward far enough to access the electrical connection. <LI type=1>Disconnect the headlamp electrical connector from the forward lamp harness connector. <LI type=1>Remove the headlamp assembly.
  2. Aim the headlamps after installation. Refer to Headlamp Aiming .

Jan 07, 2011 | Chevrolet Malibu Cars & Trucks

1 Answer

2006 jeep grand cherokee front headlight removal blue print


  1. Disconnect and isolate the battery negative cable.
  2. Remove the cover from over the top of the front lamp unit
  3. Remove the grille from the front of the vehicle.
  4. If the front lamp being serviced is on the same side of the vehicle as the engine fresh air intake tube, unsnap the air intake tube from the air cleaner housing and remove it from between the lamp and the radiator yoke.
  5. Remove the three screws (3) that secure the two lower and the upper inboard lamp mounting brackets to the front end sheet metal.
  6. If equipped, remove the push pin fastener (2) that secures the upper outboard lamp mounting bracket to the top of the radiator yoke
  7. The lower inboard lamp mounting bracket is captured between a metal mounting bracket on the top of the front frame cross-member and a tab of the plastic front fascia reinforcement. Push the tab of the front fascia reinforcement forward far enough for lamp mounting bracket clearance while maneuvering the lamp unit inboard during removal.
  8. Pull the lamp away from the front of the vehicle far enough to access and disconnect the headlamp and dash wire harness connector (5) from the pigtail connector on the back of the lamp housing.
  9. Remove the lamp unit from the vehicle.
  10. 56fe516.gif

Oct 16, 2010 | 2006 Jeep Grand Cherokee

1 Answer

How do I remove the headlamp unit on a Jaguar S type 2001 I can only see two nuts one top centre and one to the left and three or four inches lower slightly to the right of the main beam looking from the...


Front bumper requires removal to gain acsess to the lower 10mm bolts. Bumper comes off by removing the 2 10mm bolts on the top of the bumper then unscrew the 2 T30 screws in the front wheel arch liner (bumper side) and then you will be able to see a 10mm bolt reversed into a bracket at the top of the bumper from a inside veiw, remove and repeat for the other side. Then its 3 10mm bolts that secure the front under tray (if yours has one). Then there will be another 10mm bolt to the wing side of the headlamp from a above veiw. Bumper should then just pull off and watch for the connector for the fog lamp harness.

Just the 2 lower headlamp bolts andit should pull from its housing

Mar 04, 2010 | 2001 Jaguar S-Type

1 Answer

How to change left front headlamp on 06 grand caravan?


open hood and you need to remove the 3 screws on top of the headlight , this allows you to remove the head light assembly and then gives you access to the back to put in a new bulb.

Oct 27, 2009 | 2006 Dodge Grand Caravan

1 Answer

Need to get the headlamp assembly off a 2006 jeep grand cherokee how do I get it off?


1. Disconnect and isolate the battery negative cable. 2. Remove the cover from over the top of the front lamp unit (1). (Refer to 08 - Electrical/8L - Lamps and Lighting/Lamps/Lighting - Exterior/UNIT, Front Lamp - Removal) . 3. Remove the grille from the front of the vehicle. (Refer to 23 - Body/Exterior/GRILLE - Removal) . 4. If the front lamp being serviced is on the same side of the vehicle as the engine fresh air intake tube, unsnap the air intake tube from the air cleaner housing and remove it from between the lamp and the radiator yoke hydroform. 5. Remove the three screws (3) that secure the two lower and the upper inboard lamp mounting brackets to the front end sheet metal. 6. If equipped, remove the push pin fastener (2) that secures the upper outboard lamp mounting bracket to the top of the radiator yoke hydroform. 7. The lower inboard lamp mounting bracket is captured between a metal mounting bracket on the top of the front frame crossmember and a tab of the plastic front fascia reinforcement. Push the tab of the front fascia reinforcement forward far enough for lamp mounting bracket clearance while maneuvering the lamp unit inboard during removal. 8. Pull the lamp away from the front of the vehicle far enough to access and disconnect the headlamp and dash wire harness connector (5) from the pigtail connector on the back of the lamp housing. 9. Remove the lamp unit from the vehicle.

Jul 17, 2009 | 2006 Jeep Grand Cherokee

1 Answer

1998 Mercury Villager front park light replacement


You remove the screw located at top near the corner of headlamp then gently pry the park lamp from the fender.

Mar 05, 2009 | 1998 Mercury Villager

3 Answers

How do I remove my front headlight assembly.


Solution #2 above is a rectal tonsillectomy, and it doesn't get you to the side marker lamp located in the headlamp assembly. The answer, including a good disassembled illustration is at:
http://www.justanswer.com/questions/1p6yy-how-do-you-change-a-2008-gmc-yukon-h13-headlight
The key is to remove the six bolts that attach the facia top to the hood latch bracket, and partially remove the headlamp to get access. Don't forget to loosen but not completely remove the bottom outboard bolt, accessed by partially removing the inner fender.

Nov 06, 2008 | 2007 GMC Yukon Denali

Not finding what you are looking for?
2006 Volkswagen GTI Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...