Question about 2008 GMC Yukon

1 Answer

How do you change the headlamp bulbs on a 2008 yukon?

The manual only refers to a dealer and I am trying to upgrade the H-13 Bulbs. Thanks

Posted by on

  • Anonymous Feb 13, 2009

    I have the same issue with a 2008 Yukon Denali.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

They are replaced from inside the engine compartment.... look inside at the back of where the headlights are. you may have to remove the battery to change the one on that side. if it has dual batteries ... you will probably have to remove them both.

Robert

Posted on Jan 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chrysler Sebring 2008 headlight assembly removal


some times headlamp units have a plastic retaining clip on the underside of headlamp, does the headlight move from side to side? try to pull the headlight back from the top of unit then lift up the headlamp unit, if not it could be the headlamp adjusters holding unit in place.

Dec 06, 2013 | 2008 Chrysler Sebring

2 Answers

Replacing front right turn signal bulb


what are the ways u tried....
open the bonnet, nw u can find an access to the front right lighting assembly.... u can change the bulb nw 

reply back

Jun 15, 2008 | 2007 GMC Yukon Denali

2 Answers

I cant seem to take out the headlight to change the turn signal after taking out the to bolts on top i cant seem to find or see a thrid or fourth bolt? o and my car is a 2008 ford focus se.


Please rate if this helps you.

Removal and Installation
  1. Remove the radiator grille. For additional information, refer to Section 501-08.
  1. NOTE: There is a blind metal snap located on the lower outboard side of the headlamp assembly that is disengaged by pulling upwards on the headlamp assembly.
    Remove the 3 bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
  1. To install, reverse the removal procedure.
    • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.
Headlamp Assembly adobe.gif Printable View (174 KB) n0077642.jpg
Item Part Number Description 1 W707594 Headlamp assembly bolts (3 required) 2 13008 Headlamp assembly 3 - Headlamp assembly electrical connectors (part of 14290)

Jan 19, 2011 | 2008 Ford Focus SE Sedan

1 Answer

How do I replace the driver's side headlamp?


Lift the hood and remove the bulb from the inside rear of the headlamp. The bulb assembly has ears on it that you use to unscrew the bulb. Look at the autozone link below to see the bulb. Installation is reverse of removal. Note: DO NOT TOUCH THE NEW BULB GLASS WITH YOUR FINGERS!! They are halogen bulbs and will burnout.



http://www.autozone.com/autozone/parts/Silver-Star-Headlight/2008-GMC-Yukon-2WD/_/N-js79yZ9ci8c?counter=0&itemIdentifier=862293_0_7179_

Sep 23, 2010 | 2008 GMC Yukon

1 Answer

How to change the headlight bulb on 2009 gmc sierra driver side


1. Loosen only, do not remove, the lower outside hidden headlamp bolt (2). 2. Depress the housing support tab with a flat-bladed tool downward in order to release the headlamp assembly from the support. 3. Pull the lamp assembly slightly forward to access the electrical connection. 4. Disconnect the forward lamp harness main electrical connector from the headlamp harness.
Headlamp Screws (Qty: 2)
1 Caution: Refer to Fastener Caution .
6 Nm (53 lb in)
O Headlamp Screw (Hidden)
6 Nm (53 lb in)
3 Headlamp Housing Support


Preliminary Procedure Remove Healamp
Remove either the LF or RF headlamp assembly. Refer to Headlamp Replacement (Chevrolet) Headlamp Replacement (GMC HD)
Headlamp Replacement (HD Diesel).
Headlamp Bulb (Hi)
Warning: Refer to Haiogen Bulb Warning .
Tip: Rotate the bulb socket a quarter turn counterclockwise and remove the bulb from the headlamp.
Headlamp Bulb (Lo)
Tip: Rotate the bulb socket a quarter turn counterclockwise and remove the bulb from the headlamp.

Need more come to https://www.autorepairhelp.us


change-headlight-bulb-2009-gmc-1pzbcmqursjjtd0qcfo11o2t-2-0.png change-headlight-bulb-2009-gmc-1pzbcmqursjjtd0qcfo11o2t-2-1.png

Aug 14, 2010 | 2008 GMC Sierra 2500HD 2WD

1 Answer

I have 2008 yukon. i have replaced 7 headlamps


Check the plug ins. Than check the light bulbs and see if they are melted If that is the case than you have to find the bad wires eather way it has something to do with your wires

Apr 20, 2010 | 2001 GMC Yukon Denali

1 Answer

What are the best bulbs to put into my 2002 ford escape xls


Which bulbs are you refering to?
Headlights? I went with Sylvania SilverStar H4 bulbs. I was really impressed with the brightness. The bad news... I seem to have to replace them more often; like, 1 or 2 per year.

Another alternative is to upgrade to the 2005-2006 headlamp assemblies. Rumor says they will fit. They use a different bulb.

Apr 10, 2010 | 2002 Ford Escape

1 Answer

How do I change the headlight bulb in a 2008 Chevrolet HHR?


Access to change the headlamp bulbs is through the wheel well. The recommended method is to remove the front tire and then the plastic inner fender liner. Once removed, you'll have easy (more or less) access to the rear of the headlamp housing.

Dec 19, 2009 | 2008 Chevrolet Hhr

1 Answer

Replace headlamps 2007 GMC Yukon


It should be pretty easy, thats why there no "directions" Lift up the hood, now at the headlights there should be 2 rods, lift these rods and the lights should lift out, to access the bulbs.

Nov 06, 2009 | 2007 GMC Yukon

Not finding what you are looking for?
2008 GMC Yukon Logo

542 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

63577 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...