Question about 1995 Ford F250

1 Answer

How do I pull the right side stub shaft from the #4600 front axle in my 95 f250.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

I CAN GIVE U A NUM TO SOMEONE WHO CAN TELL U

Posted on Jan 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you pull a 1979 gmc jimmy 4x4 rear right axle


QU40221 19 Spline Outer Axle Shaft for 1977 to 1991 Chevy, GMC Corporate GM 10 Bolt Front Axle is a genuine original equipment outer axle stub shaft for all GM 10 Bolt front axles in 1977 to 1991 Chevy Blazers, GMC Jimmys, and Suburbans, plus Chevy, GMC 4x4 1/2 ton and 3/4 ton Pickups. The splined end on these new axle shafts has three snap ring grooves in three places so they are compatible with all types of automatic and manual lockout hubs plus all full-time solid splined drive gears.

Also available while supplies last: QU40221U Used Outer Axle Shaft with 3 snap ring grooves and QU40660UUsed Inner Axle Shafts with 2 snap ring grooves (QU40660U is not compatible with automatic locking hubs)



see this vdio

Apr 01, 2015 | GMC Jimmy Cars & Trucks

1 Answer

How do I replace my inner axle on the passenger side of my 2002 Dodge Ram 4x4 4.7L. I lent my truck out and the C clip let go of the CV axle. The intermediate axle spline is stripped and I need to change...


Lift and support front end on suitable jack stands preferably on frame. Remove right front cv axle, stub shaft, and seal. You will need to pull the right front brake caliper assembly loose and place to the side. Then remove bolts from shock and upper control arm and hub nut to do this. Next, remove axle lock actuator on passenger side of front axle. Place a drain pan underneath front diff cover and remove cover and drain axle. In the center of differential there will be an 8 mm head bolt holding spider gear cross-shaft. Remove bolt and cross-shaft only! Push inner axle in until clip clears inside of passenger spider gear. Set clip aside and push/pull axle shaft straight out to passenger side.

Feb 09, 2015 | Dodge Cars & Trucks

1 Answer

Im replacin the cv joints on passanger side and driver side how do i get the axle out of the transmission casing is ther a key behind the plate with the 4 bolts? my truck is a 99 isuzu rodeo LS 4wd


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Apr 20, 2011 | 1999 Isuzu Rodeo

1 Answer

The rubber cover on the left side axel is tore. I need to replace the joint I think. How do I do this?


You will need to remove the front wheel. Unbolt the caliper and move aside. Remove the rotor. Remove the axle nut. Unbolt the 3 hub/ bearing bolts and remove hub assembly. Pull the axle shaft out through the opening left by the hub bearing. Cut off the old boot and clamps. Hold axle shaft and tap joint and axle stub off of shaft with a hammer. Install new boot on shaft and reverse steps for assembly.

Feb 06, 2011 | 2000 Jeep Grand Cherokee

1 Answer

Front axle removal


remove the axle stub retaining nut, disconnect the lower ball joint, disconnect the tie rod end, pull the spindle out and away from the axle stub tapping on the end of the stub if necessary with a hammer (just be careful) to pull the bearing hub loose from the axle stub. after separating the outside slide under vehicle (make sure the car is on jack stands and the rear wheels are blocked from rolling and very secure before crawling under any vehicle) look at where the inside axle stub goes into the transmission. you'll need a good sized pry bar to pop the axle out of the transmission. work the pry bar in between the inside axle stub and a good thick part of the transmission and pry the axle away from the trans., there is a snap ring on the inside axle stub that internally retains the axle you have to pry hard enough to compress the snap ring into the axle groove which will release the axle for removal. it's not a bad idea to replace the axle seal in the transmission while you're there but if it's not leaking and you don't damage it in the removal of the axle it's not necessary. measure and compare the new axle to the old one, it may have some differences in the shaft like missing vibration dampeners but if it's the same length and both axle stubs match the old ones in size and number of teeth you should be good. when you install the new axle line it up by hand and slide it in as far as possible manually then tap it in with a wooden or rubber mallet. if you don't have a mallet use a scrap of wood to protect the new axle stub threads and tap it in with a hammer. after you feel the snap ring collapse and the axle slide in tap on it gently to make sure it's fully seated then grab the inner axle stub and tug on it to insure the snap ring is in place. then reassemble in reverse order of removal making sure all nuts and bolts are tightened properly and all retainers are in place. good luck

Jan 06, 2011 | 1997 Chrysler Concorde

1 Answer

How to remove front axle on a 2002 dodge intrepid


raise you vehicle on jackstands. remove front wheel and tire.remove front caliper from steering knuckle assembly, remove rotor from hub by pulling it staright off. remove speed sensor bracket from strut assembly. remove hub and bearing to stub axle retaining nut. dislodge inner CV stub shaft retaining ringon transaxle assembly. insert small pry bar between transaxle case and inner CV joint by prying on it.remove strut assembly to steering knuckle bolts remove top of steering knuckle from strut assembly, then rotate CV assembly out of vehicle. Remove inner shaft from transaxle stub shaft grasp inner CV joint and interconnecting shaft and pull both pieces out at the same time. good luck!

Oct 30, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

How to replace front cv shafts ?


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Aug 01, 2009 | 1997 Isuzu Rodeo

1 Answer

Grinding noise when in 4x4


check RF axle where it meets shaft coming out of front diff..cv axle splines and stub shaft splines may be stripped..have seen this before

Feb 21, 2009 | 2004 Dodge Ram 2500

1 Answer

95 f-250 right front stub shaft removal


I think if you put a pry bar behind the knuckle and give it a quick bump it will just pop out it has a ring on the inside that holds it in. Just uses pressure to keep it in place I will look in a few but I am sure that is what to do.

Jan 02, 2009 | 1995 Ford F250

1 Answer

Adjusting the rear bakes on a 95 F250 4X4


I think you pull the wrench down.

Dec 03, 2008 | 1995 Ford F250

Not finding what you are looking for?
1995 Ford F250 Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...