Question about 1989 Chevrolet K1500

1 Answer

Rear signal light do not flash

The front turn signal light flash but the rear ones do not. They act like the bulbs are burned out but they are not. The emergency flashers work.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

THE PROBLEM PROBABLE IS IN THE TURN SIGNAL UNIT IN THE STEERING COLUMN, KIND OF DIFFICULT TO GET APART BUT WITH PATIENCE AND A LITTLE INGENUITY YOU CAN FIX IT.

Posted on Jan 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I have sourced out all fuses and bulbs, yet continue to have a rapid right turn signal. I don't know where else to look. help?


replace the right rear bulb. the quick flashing indicates a bad bulb. it could be a wiring problem to the rear for the signal light that you will have to check out starting at the socket and working forward.

Mar 29, 2015 | 2005 Chevrolet Uplander

1 Answer

When I turn on lights, the turn signal lights also on at the right side and turen signal doesn't act flash


Turn the parking light and compare the brightness on all lights. Next turn the flasher and compare the brightness on all light. Some time light bulb like 1157 will be insert the wrong way and short the light to signal. second open the light socket remove the bulb and inspect for burn mark and rust(replace the socket.
Behind the carpet is the ground point, clean and tight the ground.
and last is the combination switch for light and signals.
Good Luck

Jan 17, 2015 | 2000 Toyota Sienna

2 Answers

Right turn signal lights flash very fast


check to see if the front or rear bulb is burned out most of the time one bulb burns out causing a faster flash on that side.

Apr 18, 2013 | 1997 Dodge Neon

1 Answer

Grand prix front turn signals lights will not work but rears flash rapidly.


Definitely not the flasher, as long as it is flashing or blinking somewhere. Rapid flashing indicates a burned bulb, but since you already tried new bulbs in front, possibly bad bulb sockets, loose connectors, or a bad ground for the front bulbs. If you have a test light or voltmeter (multimeter), check for power at the socket when turns are on. If power then at the front, try new bulbs or trace the ground for those lights. If no power to the socket for turn signals, recheck wiring.

Apr 02, 2013 | 1995 Pontiac Grand Prix

2 Answers

Left blinker flash fast, hit brake left blinker goes out left taillight goes out but both backup lights come on


Usually a fast flashing signal is because one of the bulbs is burned out or shorted out. If the signal and brakes use the same light which many cars do then check the wiring to it and replace bulb. If burns out again then it has a short between the signal switch and the actual light or the brake wiring to it is shorted.

Sep 03, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Rear turn signal and hazard light don't flash (left side only)


The rear left turn signal bulb must be replaced immediatly before it melts the light socket, if it has'nt yet. Also please verify that the correct light bulb is being installed. because even though many bulbs look the same they are not identical. Installing the wrong bulb can be the begining of many, many problems in the particular circuit

Mar 26, 2010 | 2000 Ford Focus

1 Answer

Signal lights flash faster than normal, back signals work front ones do not, front lights work when head/parking lights turned on.


The fast signal flashing indicates that you have a burned bulb (or one of the bulb elements is burned).
Based on your saying it's the front one on the side your flasher control is set when the signal light flash faster

By a new bulb light and replace the faulty one
hope it will help

Dec 28, 2009 | Mazda B2200 Cars & Trucks

1 Answer

1998 wrangler turn signal/brake light short


your socket may not be grounded properly, I have seen this before, and the simplest way to fix is change the socket with a new one.Not another used one it may also be bad.

Jul 30, 2008 | 1988 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...