Question about 1995 Chevrolet Caprice Classic

3 Answers

Flasher or turn signal switch

The turn signals dont work but the emergency flasher does

Posted by on

  • 11 more comments 
  • daphatom Jan 20, 2009

    I have the same problem no lights came on but the hazard lights do work. I replaced the turn signal flasher and the turn signals now work, but now the flasher buzzes when the turn signal switch is off, but the buzzing stops when i turn the turn signal on (either left or right). I replaced the turn signal/hazard switch and it still buzzes. Any help would be greatly appreciated.

  • Anonymous Jan 22, 2009

    After spending several hours trying to find the problem with my turn signal problem I gave up and sat in the car frustrated. I started giggling the ing. key in the on position and all of a sudden the lights started to work. I haven't confirmed that it is the ing switch but maybe this could be the problem.

  • Anonymous Jan 23, 2009

    where is the flasher fuse locatedon a 95 buick skylark

  • captainspeed Jan 23, 2009

    where is the flasher fuse located on a 95 buick skylark
    mine stop working no noise

  • daphatom Jan 25, 2009

    So far i have checked the ground it's fine the problem was in the wire for the turn signal. It seems to be the only one causing the buzzing, the wire splits from the flasher to the turn switch and to a white box. I disconnected the wire to the switch and it still buzzes. i took out the white box(has a circuitboard in it) and the buzzing stopped with hazards and turn signals working fine. In the service manual this box is called the convenience center. since i unplugged it the interior lights, seat belt alarm, ignition/key alarm and headlight left on alarm, won't work. going to a junkyard today to try to find that part, can't find it in any parts store, PN number on the box doesn't show anything on ACDELCO site, and dealer would probably want an arm/leg and left ear for that part. any help or information on this part would help A LOT!! THANKS!

  • Anonymous Jan 30, 2009

    hazard flasher on always unless headlights but still hear clinking from dash

  • Anonymous Feb 09, 2009

    i have this same rpoblem in my 95 jeep cherokee the hazards work but not the turn signals, and i tried replacing the flasher with no avail

  • herb3171 Feb 12, 2009

    My left turn signal will light up (front & back) but will not flash. The right one is OK & works just fine. All of the lights work when the hazard switch is on.

  • Kerry
    Kerry Mar 04, 2009

    I have a 97 dodge avenger 2.0, the turn signals will NOT work, however when I put on my fourways/hazard lights- they work--sound and all lights. I went to change the fuse, using the same amp (10) only the drivers side light inside would work, and even in the off position, they continue to blink. I got a flasher/starter unit but cannot locate where it is. I tried following the blink sound but no luck. I went online, to find a diagram- however the flasher unit housing does not look anything like the unit I purchased. Is the unit inside the housing? reason I question, is I dont want to have to remove the heater/radio cover to access said unit and it not be it.
    Any assistance greatlty appreciated. PS. Is there a diagram online that shows all parts to this make/model of car so that I could have as a reference.

    thanks guys!

  • Carl Maxwell
    Carl Maxwell Apr 06, 2009

    I HAVE A 73' FORD MAVERICK,WHEN I TURN MY LIGHTS ON,THE GAS GUAGE GOES UP,AND BOTH TURN SIGNALS,COME ON BUT WON'T BLINK.

  • Anonymous Apr 18, 2009

    Turn lights do not blink, hazard lights does. It is a Ford Fiesta 1.4, does it use the same relay or not?

    Thanks.

  • vinces bride May 04, 2009

    My brake ligths and back signals do not work. Does any one know where the fuse box is located in a 2006 Ford Taurus?

  • sport321 May 10, 2009

    i have 2009 kia spectra that had remote door lock added now they do not work or turn signals,or flashers. fuses look good

×

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 227 Answers

When you select left or right do any of the bulbs come on? If you select left check front and back left side if one of the bulbs did not come on the flasher will not work. Change the bulb that is out. Same with the right. If the fuse for the turn signal is good (check fuse or replace do not use visual, some appear to be good but are not).
The emergency flasher is different from the turn signal flasher. Look at manual for location of turn signal flasher. If you manually lift and lower turn signal control you may hear a clicking under the dash to locate the flasher.

Posted on Jan 12, 2009

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 25 Answers

BOTH SIGNAL AND FLASHER ARE LOCATED ON DRIVER SIDE UNDER DASH ABOVE THE KICK PANEL MOUNTED AT THE BOTTOM OF CONVENIANCE PANEL

Posted on Feb 25, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Why does the electric slide door on my 95 transport shut and open never satying shut

Posted on May 20, 2009

6 Suggested Answers

  • 272 Answers

SOURCE: 1997 sonoma turn signal flasher

The flashers are located behind the instrument panel trim, roughly between the base of the steering wheel and the ashtray, just to the left of the car lighter. To access the flashers, you need to at least loosen the lower instrument panel trim. Just under the steering column there are two screws with star heads. One to the left of the column and one to the right. You need to remove both of these screws. You will need to remove your ashtray. On the upper left corner of the hole left by removing the ashtray is a 9/32 hex head screw. You need to remove it. Once these three screws are removed you should be able to pull down on this portion of trim under your instrument cluster. When you do this it may cause trim around your instrument cluster to loosen that you can just pop back into place with your hand. You won't need to pull down to far on this trim piece as there are still some screws holding the bottom. You should be able to pull it down far enough to see the flasher units behind and just to the left of the cigarette lighter. There are two flasher units and I found that the one on the right is for the turn signals.On the left the other is for the hazard flashers. It may be a hand scraping experience to replace the flasher but it beats paying someone to do it for you. They are easy to recognize because the are silver and round metallic plug ins. The flasher unit on the left is for the emergency flashers and the one on the right is for turn signals. You can place the emergency flasher unit into the slot the turn signal unit belongs until you get a replacement. These flasher units are pretty cheap.

Posted on Jun 02, 2009

  • 1168 Answers

SOURCE: Turn signals not working.All bulbs are good,no

The emergency flasher and the turn signal flasher are two separate items. You could have a defective T/S flasher.

Posted on Oct 30, 2009

  • 286 Answers

SOURCE: emergancy flashers work but turn signals dont

Check fuses , they operate on different circuits, ie ignition or battery dependant on switchwork. But unlikely to be a short in indicator circuit seen as 4way works fine but still may be a fault in a shared circuit . You may be down another electrical componant but are unaware at the moment ! Good luck

Posted on Apr 11, 2010

emissionwiz
  • 61203 Answers

SOURCE: 1997 sonoma turn signal flasher

it is inside, under dash, on left side is a plastic sound protector, mine had 3 screws holding it up, drop this down and straight in you will see a 1" round thing - this is the flasher, pull it out and replace with new one (there are two flat prongs that plug in). It appears this is a well guarded secret!

Posted on Aug 26, 2008

  • 1 Answer

SOURCE: Turn signal/ Emergency Flasher

yes happens all the time.  I've had to replace mine like many other vette owners.  Order it from gmpartsdirect.com and search vette forums for how to replace hazard switch.  You should find the directions on how to replace it without taking apart the whole dash.  Not very diffiecult.

Posted on Sep 19, 2008

  • 4 Answers

SOURCE: 1997 Chevy Tahoe both turn signals stopped working

Sounds like the flasher unit to me. Normally the emergency flasher and turn signal are separate.

Posted on Jul 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flashers work fine but turn signals dont work


Well the emergency flashers and turn signals are on two different circuits.
Have you checked the turn signal fuses and to see if you have power in and out of the turn signal switch ?

Jan 28, 2013 | 1995 Chevrolet Corsica

1 Answer

Turning signals dont work but hazzerds do


The turn signal flasher is separate from the emergency flasher. It could also be the turn signal fuse, burned out bulbs, dirty or corroded sockets and lastly the turn signal switch.

Mar 13, 2011 | Pontiac Firebird Cars & Trucks

1 Answer

Turn signals dont work. emergency flashers do work. bulbs ok .cant find turn signal spicific fuse .


there is no specific fuse for turn signals, you are looking at a switch or flasher

Nov 19, 2010 | Plymouth Voyager Cars & Trucks

1 Answer

I drive a 2000 mitsu. mirage. my turn signals just stopped working. i checked the bulbs the fuses they're good. the emergency flashers work im wondering if maybe its the turning module but i dont know...


The emergency flasher switch is also the turn signal flasher It pops out of the dash and can be replaced easy. do chaeck the fuses before going to this much troble. check all the fuses as some work backup circuits that you wouldn;t think would be important. Before replacing the flasher switch ( you may only be able to buy it from the dealer) work the switch several times and the flashers will come on cheak to see if allthe lights work thenturn the flashers off and see ( with the key on if the turn signals now work. Now if during the test with the four way flashers you see a bulb or more out you know that the turn signals wouldn't work, but the four ways will. they work on different fuses so chak the turnsignal fuse too. after cycling the switch try the turn signals again as the switch is likly to stick and sometimes cycling it will get the turn signals working again. Fooling around with the switch you may find a position that the turn signals work. if you can't get it to stay working then you'll have to change the flasher emergency switch.

Sep 30, 2010 | Mitsubishi Mirage Cars & Trucks

1 Answer

Turning signals will work only when emergency flasher switch is set to the on position /also the emergency flashers do not work at all/


Check the flasher unit, switch the emergency flasher with signal flasher see if emergency will work. Possibly they run off same "double flasher", probably replace it.

Sep 17, 2009 | 1996 Ford Thunderbird LX

1 Answer

Emergency flashers work but turn signals dont


Your signals work on a seperate system then your flashers. Sounds like your multifunction switch is busted.

Apr 07, 2009 | 2003 Jeep Grand Cherokee

3 Answers

Turning signals dont blink


Problem is the Turn Signal "FLASHER" unit, 1.Turn on Emergency FLASHERS 2. Go under Dash while they are on Listen -for Clicking sound then feel for it 3. Should Be a Silver Round Unit About as Big IN ROUND as Half dollar coin 4. ok now Look Around for the SAME EXACT Thing Clipped onto Something Under dash At Driver side Usually Between Steering wheel and Center HUMP in Floor, 5. once you find it Take OUT the first One you Found Emergency FLASHER) and 6. Put it In Place of Turn Signal Flasher, 7. Turn off Emergency Flashers- Turn Key in "ON" Position but don't start then Try Turn Signals. Yaaaa !!!! they work ?? LoL hopefully this Does the trick, if they work Buy new one and Replace Always Use NEW For TURN Signals as they are used Much More than Emergency Flashers. Hope this is Good Instructions For you and Helps you Solve The Problem, Please DONT Forget to RATE ME Thank you Rejakwilson@aol.com

Jan 18, 2009 | 1986 Oldsmobile Cutlass Supreme

1 Answer

Blinker dont work flasher and other lights work


The turn signals don't work, but the emergency flashers do? If that's the case, replace the flasher, you have 2 flashers, one for emergency (hazard) flasher, and one for the turn signals. It should be on the fuse block under the dash.

Oct 23, 2008 | 1995 Jeep Cherokee

6 Answers

Both turn signals do not work or works intermitantly


There is a recall on the alero for this issue. We had the same with our 01 alero and they fixed it under the recall.

Jul 26, 2008 | 2001 Oldsmobile Alero

Not finding what you are looking for?
1995 Chevrolet Caprice Classic Logo

12,440 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...