Head gasketrepair i need the head bolt pattern & torque for a 86 ford escort 4 door sedan

Head bolt pattern 4.0 - Jeep Cherokee Forum

https://www.cherokeeforum.com > head-bolt-pattern-4-...
Apr 12, 2017 - step 4...tighten all bolts except #11 to 110ft/lbs, then tighten #11 to 100ft/lbs... JeepingDan's Avatar.
Torque specs. for 4.0 cylinder head 2002 - Jeep Cherokee ...
Jun 23, 2017
cylinder head torque specs on 94 4.0 - Jeep Cherokee Forum
Sept 2, 2015
4.0 torque specs - Jeep Cherokee Forum
Apr 12, 2017
Cylinder Head Bolts & Torque - Jeep Cherokee Forum
Oct 1, 2019
More results from www.cherokeeforum.com

Videos as well.

https://www.google.com/search?q=torque+sequence+of+the+head+bolts+on+a+1999+Jeep+Cherokee+4.0

..

Here are the torque settings for a Ford Fiesta 1.4 2010 for the main bearings, head bolts, and big ends:
Main bearings

• Main bearing caps: 1st stage - 7 Nm, 2nd stage - 16 Nm
• Main bearing bolts: 45 Nm + 90°

Head bolts

• Cylinders 1-3: 2nd stage - 30 Nm + 90°, 3rd stage - 80 Nm + 180°
• Cylinder 4: 2nd stage - 25 Nm + 90°, 3rd stage - 60 Nm + 180°

Big ends

• Connecting rod cap nuts: 1st stage - 22 Nm, 2nd stage - 40 Nm + 90°

Please note that these are just the general torque settings. The exact torque settings may vary depending on the specific engine and vehicle. It is always best to consult your vehicle's service manual for the correct torque settings.
Here are some additional tips for tightening the torque settings:

• Use a torque wrench to ensure that the bolts are tightened to the correct torque.
• Tighten the bolts in a star pattern, working your way from the center out.
• Do not overtighten the bolts, as this can damage the engine.

On the scale of engine repairs - changing a head gasket is a precise job.

A torque wrench is required to put the right amount of tension to the bolts when refitting the head. Sometimes the cylinder head won't come of that easily - an engine hoist is a big help to get the head of evenly at every side.

Then removing the old gasket can take sometime since it can't be scraped of by force. When rebolting the head - the order in which bolts are fixed is very important - you need the bolt pattern from a service manual.

The rest of the job is rather straight forward - best to do inside.

TORQUE IS 13 - 20 FT LBS. TIGHTEN BOLTS GRADUALLY IN A CRISS CROSS PATTERN.

head bolt torque about 120lbs

Torque new cylinder head bolts in sequence to 44 ft lb. Loosen bolts approximately two turns, then torque bolts in sequence to 44 ft lb. Turn bolts an additional 90 degrees in sequence, then an additional 90 degrees

Torque sequence
9 3 1 5 7
8 6 2 4 10

call your local parts store-they can get it for you (I know Auto Zone can)

Always use new head bolts.
1)tighten to 40ft/lbs
2)back off 1/2 turn
3)tighten back to 40ft/lbs
4)tighten an additional 90 degrees
5)tighten an additional 90 degrees.

2lt overhead cam with them horrible tappet adjusters,cast iron head but valves dont hit the head if the timing belt breaks ,but it does on the 1600 .called a pinto in america .Remember the assembly line well ,have many a fond memory of working on it and the staff canteen on night shift ,what lovely grub we got.Head bolt torque is about 80lbs because i used to pull them down to check them after the machine had tightened them up

torque the bolts to 45 ft/lb then tighten each bolt 90 degrees and then 90 degrees again