Question about 1995 Isuzu Pickup

1 Answer

Can't get motor in time

Motor got out of time, can't get cam, crank,and distributor in time, need help

Posted by on

  • 3 more comments 
  • stanleymayla Jan 18, 2009

    i dont understand what you mean remove the fixya to see it

  • stanleymayla Jan 18, 2009

    i didnt mean to rate it solved I am not any closer now than before

  • stanleymayla Jan 18, 2009

    No, sorry for all the trouble.

  • stanleymayla Jan 18, 2009

    No, sorry for all the trouble.

  • stanleymayla Jan 18, 2009

    No, sorry for all the trouble.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

I have provided a solution for your premium question... i suspect you will need to remove the fixya to see it.

Posted on Jan 18, 2009

  • Roberta Smith
    Roberta Smith Jan 18, 2009

    you asked a premuim question regarding an oil filter ... i answered it with the likely solution... i'm not sure you can see the answer as you have already rated it as solved...



    Robert

  • Roberta Smith
    Roberta Smith Jan 18, 2009

    I may be incorrect ... but i believe you can change the rating... have you seen my solution ?



    Robert

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i put motor and distributor shaft in corret timing postion


have to get Piston #1 up at TDC then point distributo rotor to #1 Plug wire. Very hard on these newer cars since they have a Cam Sensor and Crank Sensor that look at each other.

Nov 20, 2012 | 1991 Chevrolet C1500

2 Answers

Reset timing on chain for 85 olds cutlass


I used to have one of these...there are 2 top dead centre positions you have to watch for. Top Dead Centre "Compression" and Top Dead Centre "Exhaust".

With the distributor cap on, you will know where number 1 is on the distributer, remove the distributor cap and then turn the motor using the crank...keep turning until you see the rotor pointing to number 1. If the number 1 piston is at TDC then you are good to go with it being at TDC Compression- rotor at 1.
If your rotor is at number 1 but your number 1 piston is down then you need to remove the distributor from the rotor 180 degrees then slide the distributor back into the block carefully...remembering to be careful because your oil pump is run by a shaft which snaps onto the bottom of the distributor.

Jul 04, 2012 | Cars & Trucks

2 Answers

How to time a distributor 305 a96 gmc sirrera truck 4x4 z71


u cant electricaly time it-no more points--mite hav a bad ignition module or the distributer cap cud be corroded inside---------if the distributer was taken out u need a repair manual to line it up with piston # 1

May 27, 2012 | Cars & Trucks

1 Answer

I have a 95 dodge ram 1500 318 just did a rebuild on the motor and i am am having problems timing it I have put it in timing but it seems it keeps getting out of timing.. it have a new timing chain and...


Number one piston all the way up. Your crank pully should line up "zero" or TDC with the line on the pulley.
The rotor should be pointing to the #1 spot on the distributor cap. (If it's off, it will be facing 180 degrees off, then turn the crank one revolution.) If this doesnt jive, your distributor may be off a tooth.
Also, ...are you sure the cam was positioned correctly? (With the crank pulley at the TDC mark, the dot on the lower gear straight up, and the cam gear mark straight up.)

Sep 07, 2011 | Dodge Ram 1500 Cars & Trucks

2 Answers

Where are the cam & crank position sensors for a 1999 chevy suburbon 5.7?


THE crank sensor is located at bottom of timing cover on front of engine if you look under engine below crank pulley around oil pan timing cover you will see it. the cam sensor is in the distributor.

Dec 22, 2010 | 1999 Chevrolet K1500

1 Answer

1994 honda accord distributor not turning


you mean to say the distributor rotor doesnt turn? if thats the case you either have a broken camshaft, broken timing belt or broken distributor drive, better pull out the distributor and see if the cam turns when you crank the motor...

Jun 22, 2009 | 1994 Honda Accord

2 Answers

2000 isuzu trooper 3.2 v-6 dohc camshaft timing marks pulled camshafts to do valve job and need to align marks on drive gear and cams


It's more to it than aligning the marks since the cam pulleys turn about three times or more to one turn of the camshaft on this engine. You need to find someone that is experienced on this vehicle.

May 12, 2009 | 2000 Isuzu Trooper

1 Answer

96 gmc 1500 4x4 with vortec motor


Timing is not adjustable. You do however need to turn the distributor to set the cam/crank correlation to keep the check engine light off. Although you need to hook it to a scanner to be able to set this.

Mar 06, 2009 | 1996 Chevrolet K1500

1 Answer

Need to know how to set timing on 1995 honda del sol d15


position of distributor = ignition timing
position of cam in relation to crank = cam timing

You should be able to from before to past the red mark while the distributor is within the the limits of travel the bolts that hold it on allow. If you cant -- then the most likely reason is that your cam timing is off by a tooth.

before you can set ignition timing, you need to have the correct cam timing.
no amount of ignition timing can compensate for incorrect cam timing.
You need to make sure that when the cam is at TDC, so is the crank.
until you have this resolved the marks on you crank pulley are meaningless, in other words you will not be able to set the ignition timing.
sorry this is hard to explain

Jan 14, 2009 | 1995 Honda Civic del sol

Not finding what you are looking for?
1995 Isuzu Pickup Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...