Question about 2000 Jaguar S-Type

1 Answer

S Type Jag 2000 Back windows fallen inside doors. How to take door panel off?? Thanks

Posted by on

  • sue_seymour Jan 02, 2009

    Thanks very much. This is much appreciated

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Inside thr rear pull handle pickout the black rubber cover there vare screws under that. the other screws are obviuos. You will need a new window regulator to fix your problem get one in advance. you will also need a very large rivet gun or take the car to a glass shop.

Posted on Jan 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix fallen window in car door


Go to You Tube Video & see how to remove the inner door panel,
so you can see the problem

Have to replace a broken window regulator inside the door

Mar 26, 2013 | 2000 Ford Focus

1 Answer

Door will not open 2002 x type jaguar


The cable that goes to the inside door handle has fallen off, you have to remove the inner panel and look at the back of the handle, you should see a cable, most likely the cable fell off the retaining slot. Just push it back on until it bottoms out and replace the panel. This is common with door slamming, on x-types.

May 25, 2012 | 2002 Jaguar X-Type

1 Answer

X-Type Jag 2002 off side rear passenger door will not unlock. Cant open from inside or out.


Your rear door lock lever rod seems to have come off and is therefore not releasing the lock. You will have to open the inner door opener lever and try to somehow reach the place from where our lever rod has come off, manually release it, open the door, its inner door panel and put the rod back in its proper place.

Apr 07, 2012 | Cars & Trucks

1 Answer

How do you remove a back door panel on a 2000 Pontiac Grand Prix GT to fix a window that has fallen off the track?


remove the door handle screws, and possibly the armrest has some screws hidden under dimples. then remove door handles from metal linkage and use a small putty knife or flat screwdriver and gently pop the door panel loose from the door. there are little press in plastic tabs that are connected to the door panels that just pop out of the holes on the doors , if you be careful and wedge away from the door with the screwdriver

Jul 31, 2010 | 2000 Pontiac Grand Prix

2 Answers

Front passenger window has fallen down into door


The window either came unattached from the window regulator or your power window motor's gears inside are stripped, either way you need to take the door panel off to diagnose the problem.

May 26, 2010 | 2000 GMC Yukon XL

1 Answer

The front driver side door's outside handle on my 1996 Ford Explorer became very loose. It still works but I wanted to know how to take off the door panel to look inside to see how I can fix it. Thanks


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Pull back the weather seal and you'll be able to get to everything. Either the bolts holding the outer handle on has broken or fallen out, or the handle anchor (plastic) has broken

Sep 18, 2009 | 1996 Ford Explorer

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

The front drivers door window has fallen off its track and fallen inside the door panel. My car is a 1995 mercury marque. I'm trying to take off the door panel. PS I'm a female so this is new for me . It's...


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Dec 12, 2008 | 1995 Mercury Grand Marquis

1 Answer

Door Panel


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Jul 29, 2008 | 2000 Jaguar S-Type

4 Answers

Door window on 2000 jaguar s type


take off inner door panel, lower track and put the window back in. If parts on track are broken buy new ones. Use urathain to reinstall window.

Jul 28, 2008 | 2000 Jaguar S-Type

Not finding what you are looking for?
2000 Jaguar S-Type Logo

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Raygin
Raygin

Level 2 Expert

322 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...